Timing Chain TENSIONER - Engine Set (G1841712): Installation

1. CAUTION:

   • Use only a plastic scraper when removing the sealing material.
   • Make sure that the mating faces are clean and free of foreign material.
   • Make sure that the Land Rover approved cleaning fluid (Loctite 7063) is used to clean the mating faces.

   Apply RTV sealant (Loctite 5901G) to the areas shown.

2. CAUTION: Make sure that a new component is installed.
   NOTE: Tighten the retaining bolts in the indicated sequence.
   Fig 1: Lower Timing Cover Bolts Tightening Sequence

   Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

   Tighten the lower timing cover bolts within 7 minutes.

   Torque Specifications: 12 Nm 

3. Tighten the lower timing cover bolts within 7 minutes.

   Torque Specifications: 12 Nm 

4. NOTE: Lubricate the O-ring seal with clean engine oil.

   Torque Specifications: 12 Nm 

5. CAUTION:

   • Use only a plastic scraper when removing the sealing material.
   • Make sure that the mating faces are clean and free of foreign material.
   • Make sure that the Land Rover approved cleaning fluid (Loctite 7063) is used to clean the mating faces.

6. Apply RTV sealant (Loctite 5901G) to the areas shown, install the component, and tighten the bolts within 7 minutes.

7. CAUTION: Take extra care not to damage the seal when installing the component.
8. NOTE: Tighten the retaining bolts in the indicated sequence.
   Fig 2: Timing Cover Retaining Bolts Tightening Sequence

   Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

   Torque Specifications: 12 Nm 

9. Torque Specifications: 12 Nm 

10. Torque Specifications: 10 Nm 

11. CAUTION: Using a suitable tool, lock the component.

    Torque Specifications: 25 Nm 

12. CAUTION:

    • Use only a plastic scraper when removing the sealing material.
    • Make sure that the mating faces are clean and free of foreign material.
    • Make sure that the Land Rover approved cleaning fluid (Loctite 7063) is used to clean the mating faces.

13. Apply RTV sealant (Loctite 5901G) to the areas shown, install the component, and tighten the bolts within 7 minutes.

14. CAUTION: Take extra care not to damage the seal when installing the component.
15. NOTE: Tighten the retaining bolts in the indicated sequence.
    Fig 3: Timing Cover Retaining Bolts Tightening Sequence

    Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    13

    Torque Specifications: 12 Nm 

16. Torque Specifications: 12 Nm 

17. Torque Specifications: 10 Nm 

18. NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

19. Torque Specifications: 10 Nm 

21. CAUTION:

    • Lubricate only the union threads with clean engine oil.
    • Only tighten the bolts finger-tight at this stage.
    NOTE: Remove and discard the blanking caps.
22. Fig 4: Fuel Supply Lines Bolts Tightening Sequence

    Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Torque Specifications: 

    Unions (1) 21 Nm 

    M6 (2) 11 Nm 

    M8 (3) 25 Nm 

23. Torque Specifications: 48 Nm 

25. Torque Specifications: 12 Nm 

27. Torque Specifications: 25 Nm 

29. Refer to: Air Deflector .
30. WARNING: The wheel and tire assembly will be heavy.
    CAUTION: Apply a small amount of grease to the hub and wheel mating surfaces before installation. Make sure the grease does not come into contact with the vehicles braking components and the wheel stud threads. Failure to follow these instructions may result in personal injury.

    Install the RH front wheel and tire.

    Torque Specifications: 125 Nm 

31. Install the FEAD belt.

    Torque Specifications: 25 Nm 

32. Torque Specifications: 48 Nm 

33. Torque Specifications: 48 Nm 

34. Refer to: CRANKSHAFT PULLEY (G1785731) .
35. NOTE: Remove and discard the blanking caps.

    Torque Specifications: 

    Unions 21 Nm 

    M5 nut 6 Nm 

36. CAUTION:

    • Remove and discard the blanking caps.
    • Only tighten the bolts finger-tight at this stage.
    • This fuel pipe can be re-used, inspect for signs of damage. Renew if necessary.

37. Torque Specifications: 

    Unions 21 Nm 

    Bolts 8 Nm 

42. Refer to: AIR CLEANER OUTLET PIPE T-CONNECTOR - V8 5.0L PETROL (G1269170) .
43. Refer to: COOLING SYSTEM PARTIAL DRAINING, FILLING AND BLEEDING - V8 5.0L PETROL (G1447430) .
44. Connect the battery ground cable.

Refer to: BATTERY DISCONNECT AND CONNECT .