LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2017 >> XJR L >> Repair and Diagnosis >> External Pages >> Different car >> Section 7 (Engine - V8 N/A 5.0L Petrol -- XJ/X351) >> Engine - V8 5.0L Petrol >> General Procedures >> Engine Oil Draining And Filling (G1280231) >> Filling

Engine Oil Draining And Filling (G1280231): Filling

WARNING: This page is about a different car, the 2013 Jaguar XJ, 2012 Jaguar XJ, 2011 Jaguar XJ, and 2010 Jaguar XJ. However, it is still accessible from the selected car via links, so may be relevant.
    CAUTION: Make sure that the area around the component is clean and free of foreign material.
    NOTE: Install a new sealing washer.
  1. Torque Specifications: 24 Nm 
    G11284816
  2. Refer to: Air Deflector .
    3. NOTE: Install new O-ring seals.
  3. Lubricate the oil filter element O-ring seal with clean engine oil.
    G11284817
    4. CAUTION: Tighten the component finger tight first.
  4. Torque Specifications: 25 Nm 
    G11284818
    5. CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and that the engine oil level is reading at least minimum (by following Steps  9- 16), before starting the engine.
    • Fill the engine with oil - for filling values on vehicles without supercharger:

      Refer to: Capacities .

    • Fill the engine with oil - for filling values on vehicles with supercharger:

      Refer to: CAPACITIES .

    • Clean any residual engine oil from the oil filler cap area.
  6. G11284819
    7. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with oil.
  7. Follow the Steps  9- 16 before starting the engine.
    • Start the engine and allow to run for 10 minutes, stop the engine.
    • Check for leaks.
  9. CAUTION:
    • Make sure that the selector lever and the gearshift mechanism are in the park (P) position.
    • Make sure that the hood is open.
    • Turn the ignition on.
  10. G11284820
    • Press the right-hand directional button to access the instrument cluster menu.
  11. G11284821
    • Press the right-hand OK button.
  12. G11284822
    • Press the right-hand directional button to access the Oil Level Display.
  13. G11284823
    • Press the right-hand OK button and follow the instructions.
  14. G11284824
    • Press the cruise control cancel button twice within 2 seconds.
  15. G11284825
    • The message center display will revert to the normal display in the trip computer.
    • Press the right-hand OK button and follow the instructions.
    • Check that the oil level display shows an oil level reading.
    • Only after having started and run the engine for 10 minutes (as indicated in Step  8), switch off the engine, then stabilizing for 10 minutes, take a reading from the oil level display and, if necessary top up with engine oil.
  16. NOTE: If instructed to follow Steps  9- 16 in a previous step, return to Step  8 and continue the procedure.

    Turn the ignition off.

  17. Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top up.
  18. NOTE: The following steps are to update the average oil level value.
    G11284824
    • Turn the ignition on.
    • Press and hold the cruise control cancel button for more than 2 seconds.
    • The message center display will revert to the normal display in the trip computer.
  20. Turn the ignition off.
  21. Turn the ignition on.
  22. G11284820
    • Press the right-hand directional button to access the instrument cluster menu.
  23. G11284821
    • Press the right-hand OK button.
  24. G11284822
    • Press the right-hand directional button to access the Oil Level Display.
  25. G11284825
    • Press the right-hand OK button and follow the instructions.
    • Make sure that the average oil level value has now been updated.
  26. Refer to: ENGINE COVER - V8 5.0L PETROL/V8 S/C 5.0L PETROL .
scientia non olet · About LEMON Manuals