LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2017 >> XJR L >> Repair and Diagnosis >> External Pages >> Different car >> Section 1 (Fuel Charging & Controls - V6 S/C 3.0L Petrol -- XJ/X351) >> Fuel Charging And Controls - V6 S/C 3.0 L Petrol >> Removal And Installation >> Fuel Rail LH (G1557477) >> Installation

Fuel Rail LH (G1557477): Installation

WARNING: This page is about a different car, the 2017 Jaguar XJ, 2016 Jaguar XJ, 2015 Jaguar XJ, 2014 Jaguar XJ, and 2013 Jaguar XJ. However, it is still accessible from the selected car via links, so may be relevant.
  1. G11288044
  2. G11288046

    Special Tool(s):  310-198

  3. G11288047

    Special Tool(s):  310-199

  4. CAUTION: If the original fuel injector is being installed, the original fuel injector clamp must installed with the fuel injector it was removed with.
    G11288042
  5. CAUTION: If a new cylinder head has been installed then the special tool 310-200-02 without the thread must be used to install the fuel rail.
    G11293419

    Special Tool(s):  310-200-01

  6. CAUTION:
    • Make sure that the area around the open fuel injector ports are clean and free of foreign material and lubricant prior to installing the fuel injector.
    • When installing the fuel injector(s), make sure that the Teflon seal is clean and free of foreign material and lubricant.
    G11293420
  7. CAUTION:
    • If new fuel injectors are installed, a new injector clamp must be installed.
    • Make sure that the fuel injector is aligned and installed into the fuel rail correctly, as noted in the removal step.
    • Tighten the fuel rail retaining bolts a turn at a time until the correct torque is achieved.
    NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.
    G11293421

    Torque Specification: 20 Nm 

  8. G11293422

    Special Tool(s):  310-200-01

  9. G11293423

    Torque Specification: 20 Nm 

  10. G11293424

    Special Tool(s):  310-200-01

  11. G11293425

    Torque Specification: 20 Nm 

  12. NOTE: Tighten the bolts in the indicated sequence.
    G11293426
    • Torque Specifications: 

      Bolt 2 30 Nm 

      Bolt 3 30 Nm 

      Bolt 1 30 Nm 

  13. G11293409

    Special Tool(s):  303-1450

    Torque Specification: 20 Nm 

  14. G11293408

    Torque Specification: 7 Nm 

  15. G11293407
  16. CAUTION: Lubricate only the union threads with clean engine oil.
    NOTE:
    • Do not tighten at this stage.
    • Remove and discard the blanking caps.
    G11286716
  17. G11286716
    • Torque Specifications: 

      Unions 21 Nm 

      Bolts 8 Nm 

  18. G11286769
    • Torque Specification: 21 Nm 
  19. G11288198
  20. G11288197
  21. CAUTION: Be prepared to collect escaping fluids.
    G11288196
  22. G11288195
  23. G11288194
  24. Refer to: Secondary Bulkhead Panel LH .
  25. Refer to: ENGINE COVER - V6 S/C 3.0L PETROL .
  26. Refer to: Battery Disconnect and Connect (General Procedures).
scientia non olet · About LEMON Manuals