General Procedures: Filling

1. NOTE: Take care not to restrict coolant flow within the coolant hoses.
   • Remove the coolant expansion tank retaining bolt.
   • Raise and support the coolant expansion tank in a horizontal position above the radiator bleed screw.

2. Open the bleed screw.

3. Open the bleed screw.

4. Open the bleed screw.

5. Open the bleed screw.

6. Release the front finisher and position to one side.

7. Open the bleed screw.

8. Disconnect the right side auxiliary radiator inlet hose.

9. CAUTION: Record the volume of coolant added to the coolant expansion tank.
   • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
   • If coolant is visible from the outlet, close the bleeding point.

   Torque Specification: 2 Nm 

10. CAUTION: Record the volume of coolant added to the coolant expansion tank.
    • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
    • If coolant is visible from the outlet, close the bleeding point.

    Torque Specification: 2 Nm 

11. CAUTION: Record the volume of coolant added to the coolant expansion tank.
    • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
    • If coolant is visible from the outlet, close the bleeding point.

    Torque Specification: 2 Nm 

12. CAUTION: Record the volume of coolant added to the coolant expansion tank.
    • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
    • If coolant is visible from the outlet, close the bleeding point.

    Torque Specification: 2 Nm 

13. CAUTION: Record the volume of coolant added to the coolant expansion tank.
    • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
    • Connect the auxiliary radiator feed hose.
14. CAUTION: Record the volume of coolant added to the coolant expansion tank.
    • Fill the coolant expansion tank to the maximum mark and continue until coolant is visible from the outlet or the coolant expansion tank remains full.
    • If coolant is visible from the outlet, close the bleeding point.

    Torque Specification: 2 Nm 

15. Connect exhaust extraction hoses to the tail pipes.
16. CAUTION:

    • Do not accelerate the engine above idle speed.
    • Observe the engine temperature warning indicator. If the warning indicator is displayed, switch off immediately and allow to cool. Failure to follow this instruction may cause damage to the vehicle.
    • Select dynamic driving mode.
    • Set the heating system to 'MAX' heat, the blower motor to 'MAX' speed and the air distribution to the instrument panel vents.
    • Start and run the engine at idle until warm.
17. CAUTION:

    • Observe the engine temperature warning indicator. If the warning indicator is displayed, switch off immediately and allow to cool. Failure to follow this instruction may cause damage to the vehicle.
    • Record the volume of coolant added to the coolant expansion tank.
    • Maintain the coolant level at the maximum mark of the coolant expansion tank.
    • Observe the remaining open bleeding points.
    • Once coolant is visible from each bleeding point, close the bleeding point.
18. CAUTION: Observe the engine temperature warning indicator. If the warning indicator is displayed, switch off immediately and allow to cool. Failure to follow this instruction may cause damage to the vehicle.
    • Once all the bleeding points are closed, increase the engine speed between 2500 rpm and 3500 rpm.
    • Run the engine until the thermostat opens and hot air is emitted from the heater vents.
19. CAUTION: Record the volume of coolant added to the coolant expansion tank.

    Maintain the coolant level in the coolant expansion tank at the maximum mark using a 50% mixture of Jaguar Premium Cooling System Fluid or equivalent, meeting Jaguar specification WSS-M97B44-D and 50% water.

20. CAUTION: Record the volume of coolant added to the coolant expansion tank.

    Continue running the engine until the coolant level in the coolant expansion tank has stabilized.

21. CAUTION: If the volume of coolant added to the vehicle is less than the volume of coolant drained from the vehicle, the bleeding procedure must be repeated. Failure to follow this instruction may cause damage to the vehicle.

    Compare the volume of coolant added to the vehicle with the volume of coolant drained from the vehicle.

22. CAUTION: Switch off the engine and allow the coolant temperature to go cold.

    Switch the engine off and allow to cool.

23. Install the coolant expansion tank into the correct position and tighten the retaining bolt.

    Torque Specification: 7 Nm 

24. If required, top up the coolant level to the maximum mark of the coolant expansion tank.
25. CAUTION: Correct installation of the coolant expansion tank cap can be obtained by tightening the cap until an audible click is heard.

    Install the coolant expansion tank cap.

26. • Reposition the front finisher in the correct location.
    • Install the retaining nut and the 4 retaining bolts and tighten to the correct torque.

    Torque Specification: 9 Nm 

27. Install the air deflector.

    Refer to: Air Deflector .

28. Install the radiator splash shield.

    Refer to: Radiator Splash Shield .

29. Install the engine cover.

Refer to: Engine Cover - Ingenium I4 2.0L Petrol .