LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2017 >> F-Pace First Edition >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> Fuel Charging And Controls - V6 S/C 3.0L Petrol - F-Pace >> Fuel Charging And Controls - V6 S/C 3.0L Petrol >> Left Fuel Rail >> Removal And Installation >> Installation

Removal And Installation: Installation

  1. G11288044

    Install a new seal.

    Renew Part: Fuel injector O-ring seals. 

  2. G11288046

    Using the special tool, install a new fuel injector seal.

    Special Tool(s):  310-198

    Renew Part: Fuel injector seal. 

  3. G11288047

    Using the special tool, correctly located the seal.

    Special Tool(s):  310-199

  4. G11288042

    Install a new fuel injector clamp.

    Renew Part: Fuel Injector replacement kits. 

  5. CAUTION: If a new cylinder head has been installed then the special tool 310-200-02 without the thread must be used to install the fuel rail.
    G11293419

    Insert the special tools.

    Special Tool(s):  310-200-01, 310-200-02

  6. CAUTION: When installing the fuel injector(s), make sure that the Teflon seal is clean and free of foreign material and lubricant.
    G11293420

    Install the fuel left side injectors.

  7. CAUTION:
    • If new fuel injectors are installed, a new injector clamp must be installed.
    • Make sure that the fuel injector is aligned and installed into the fuel rail correctly, as noted in the removal step.
    NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.
    G11293421

    Install the left side fuel rail.

    Torque Specification: 20 Nm 

  8. G11293422

    Remove the special tool.

    Special Tool(s):  310-200-01, 310-200-02

  9. G11293423

    Install the bolt.

    Torque Specification: 20 Nm 

  10. G11293424

    Remove the special tool.

    Special Tool(s):  310-200-01, 310-200-02

  11. G11293425

    Install the bolt.

    Torque Specification: 20 Nm 

  12. Fig 1: Left Side Fuel Rail Bolts Tightening Sequence
    G11293426Courtesy of ABLE BODY CORP.

    Tighten the bolts in the indicated sequence.

    Torque Specifications: 

    Bolt 2 30 Nm 

    Bolt 3 30 Nm 

    Bolt 1 30 Nm 

  13. Install the left side spark plugs.

    Special Tool(s):  303-1450

    Torque Specification: 20 Nm 

  14. CAUTION: Make sure that the spark plugs are aligned correctly.
    G11310570

    Check that the vertical section of the T mark located on top of the spark plug, is aligned to no more than 45 degrees either side from the adjoining fuel injector.

  15. Install the left side ignition coils.

    Torque Specification: 7 Nm 

  16. Connect the left side fuel injectors and ignition coils wiring harness.
  17. CAUTION: Fuel tubes may be used a maximum of 4 times, paint mark the fuel tube after each full tightening sequence.
    G11307650
    1. Install the high pressure fuel crossover pipe hand tight.
    2. Fully tighten the fuel crossover pipe unions.

      Torque Specification: 21 Nm 

    3. Fully tighten the fuel crossover pipe retaining bolts.

      Torque Specification: 11 Nm 

    4. Wait for 30 seconds.
    5. Check the fuel crossover pipe unions for the correct torque.

    Torque Specification: 21 Nm 

  18. Install the right side breather.
  19. Install the right side engine Noise, Vibration and Harshness (NVH) material.
  20. Connect and secure the brake vacuum pipe.
  21. Connect the right side coolant pipes.
  22. Install the purge valve.

    Refer to: Evaporative Emission Canister Purge Valve

  23. Install the engine cover.

    Refer to: Engine Cover - V6 S/C 3.0L Petrol

  24. Connect the startup battery ground cable.

    Refer to: Battery Disconnect And Connect

  25. Fill the cooling system.

    Refer to: Cooling System Partial Draining, Filling And Bleeding

scientia non olet · About LEMON Manuals