LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2017 >> F-Pace First Edition >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> Fuel Charging And Controls - V6 S/C 3.0L Petrol - F-Pace >> Fuel Charging And Controls - V6 S/C 3.0L Petrol >> High Pressure Fuel Pump 1 >> Removal And Installation >> Removal

Removal And Installation: Removal

WARNING: This procedure involves fuel handling. Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure to follow these instructions may result in personal injury.
CAUTION:
  • Do not allow the unions to hit the olive ends of the high-pressure fuel supply line as this may damage the ends of the high-pressure fuel supply line and allow foreign matter to enter the fuel injection system.
  • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
NOTE: Removal steps in this procedure may contain installation details.
  1. WARNING: Make sure to support the vehicle with axle stands.

    Raise and support the vehicle.

  2. Refer to: Petrol And Petrol-Ethanol Fuel Systems Health And Safety Precautions
  3. Refer to: Fuel System Pressure Release
  4. Disconnect the battery ground cable.

    Refer to: Battery Disconnect And Connect

  5. Refer to: Engine COVER - V6 S/C 3.0L PETROL
  6. Refer to: Right Air Cleaner Outlet Pipe
  7. Refer to: Air Deflector
  8. CAUTION:
    • Be prepared to collect escaping coolant.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G11286148
  9. G11286149
  10. G11286151
  11. CAUTION:
    • Be prepared to collect escaping coolant.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G11286152
  12. G11286153
  13. G11286154
  14. G11285398
  15. Refer to: Fuel Injection Component Cleaning 
  16. CAUTION:
    • Be prepared to collect escaping fuel.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    • This fuel pipe can be re-used, inspect for signs of damage.

    Renew if necessary.

    G11299812
  17. CAUTION:
    • Be prepared to collect escaping fuel.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G11285400
  18. G11309755
  19. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.

    Raise and support the vehicle.

  20. Refer to: Engine Oil Draining And Filling
  21. If equipped.

    Refer to: Halfshaft Support Bracket

  22. Refer to: Generator
  23. G11299688
  24. CAUTION: Use a wooden block to protect the oil pan when supporting the engine.
    G11309757

    Support the engine.

  25. G11307702
  26. G11307699
  27. NOTE: Wiring harnesses shown removed for clarity.
    G11309761
  28. G11299947
  29. G11299815
  30. G11299816
  31. G11299950
  32. G11299951
  33. CAUTION:
    • Make sure that the area around the component is clean and free of foreign material.
    • Be prepared to collect escaping fuel.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G11299953
  34. G11299821
  35. CAUTION:
    • Make sure that the area around the component is clean and free of foreign material.
    • Be prepared to collect escaping fuel.
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    • Remove and discard the high-pressure fuel supply lines.
    G11285412

    Renew Part: Fuel rail LH supply pipe. 

    Renew Part: Fuel rail RH supply pipe. 

  36. G11301727
  37. CAUTION: Be prepared to collect escaping oil.
    G11301728

    Loosen the Torx screws a turn each at a time.

  38. G11301729
scientia non olet · About LEMON Manuals