LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2016 >> XJR L >> Repair and Diagnosis >> External Pages >> Different car >> Section 21 (Engine - V6 S/C 3.0L Petrol -- XJ/X351) >> Engine - V6 S/C 3.0L Petrol >> Lower Timing Cover (G1779456) >> Removal And Installation >> Installation

Removal And Installation: Installation

WARNING: This page is about a different car, the 2017 Jaguar XJ, 2016 Jaguar XJ, 2015 Jaguar XJ, 2014 Jaguar XJ, and 2013 Jaguar XJ. However, it is still accessible from the selected car via links, so may be relevant.
  1. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    G11287008

    Apply RTV sealant (Loctite 5901G or Loctite 5900) to the areas shown, and tighten the bolts within 7 minutes.

  2. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    G11285178

    Install the bolts, but do not tighten fully at this stage.

    Special Tool(s):  303-1433

  3. NOTE: Tighten the bolts in the indicated sequence.
    G11287010

    Torque Specifications: 12 Nm 

  4. G11287011

    Torque Specifications: 12 Nm 

  5. Refer to: BRAKE VACUUM PUMP - V6 S/C 3.0L PETROL .
  6. NOTE: Install the bolt finger tight before final tightening.
    G11287006

    Torque Specifications: 40 Nm 

  7. G11285498

    Torque Specifications: 25 Nm 

  8. G11285500

    Torque Specifications: 40 Nm 

  9. G11287003
  10. Refer to: CRANKSHAFT PULLEY (G1851000) .
  11. Connect the battery ground cable.

    Refer to: BATTERY DISCONNECT AND CONNECT .

  12. CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and that the engine oil level is reading at least minimum (by following Steps 9 - 16), before starting the engine.
    • Fill the engine with oil:

      Refer to: Capacities .

    • Clean any residual engine oil from the oil filler cap area.
  13. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with oil.

    Follow the Steps  9- 16 before starting the engine.

    • Start the engine and allow to run for 10 minutes, stop the engine.
    • Check for leaks.
  15. CAUTION:
    • Make sure that the selector lever and the gearshift mechanism are in the park (P) position.
    • Make sure that the hood is open.
    • Turn the ignition on.
  16. G11284820
    • Press the right-hand directional button to access the instrument cluster menu.
  17. G11284821
    • Press the right-hand OK button.
  18. G11284822
    • Press the right-hand directional button to access the Oil Level Display.
  19. G11284823
    • Press the right-hand OK button and follow the instructions.
  20. G11284824
    • Press the cruise control cancel button twice within 2 seconds.
  21. G11284825
    • The message center display will revert to the normal display in the trip computer.
    • Press the right-hand OK button and follow the instructions.
    • Check that the oil level display shows an oil level reading.
    • Only after having started and run the engine for 10 minutes (as indicated in Step  8), switch off the engine, then stabilizing for 10 minutes, take a reading from the oil level display and, if necessary top up with engine oil.
  22. NOTE: If instructed to follow Steps  9- 16 in a previous step, return to Step  8 and continue the procedure.

    Turn the ignition off.

  23. Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top up.
  24. NOTE: The following steps are to update the average oil level value.
    G11284824
    • Turn the ignition on.
    • Press and hold the cruise control cancel button for more than 2 seconds.
    • The message center display will revert to the normal display in the trip computer.
  26. Turn the ignition off.
  27. Turn the ignition on.
  28. G11284820
    • Press the right-hand directional button to access the instrument cluster menu.
  29. G11284821
    • Press the right-hand OK button.
  30. G11284822
    • Press the right-hand directional button to access the Oil Level Display.
  31. G11284825
    • Press the right-hand OK button and follow the instructions.
    • Make sure that the average oil level value has now been updated.
scientia non olet · About LEMON Manuals