| The engine does not crank (starter motor does not turn) |
- Battery/charging system fault
- Engine system fault
- Transmission fault
- Transmission control switch not set to Park or Neutral
- Smart key not present/recognised
- Starter relay fault
- Starter motor ground circuit open circuit, high resistance
- Starter motor solenoid power circuit short circuit to ground, open circuit, high resistance
- Starter motor power circuit short circuit to ground, open circuit, high resistance
- Engine seized
|
- Refer to the relevant service information and check the battery and charging system. Rectify as necessary
- Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index
- Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control module for related DTCs and refer to the relevant DTC index
- Set the transmission control switch to Park or Neutral and retest
- Check that the smart key is present and recognised
- Check the operation of the starter relay. Rectify as necessary
- Refer to the applicable SYSTEM WIRING DIAGRAMs and check the starter motor ground circuit for open circuit, high resistance. Repair the wiring harness as necessary
- Refer to the applicable SYSTEM WIRING DIAGRAMs and check the starter motor solenoid power circuit for short circuit to ground, open circuit, high resistance. Repair the wiring harness or install a new starter motor solenoid as necessary
- Refer to the applicable SYSTEM WIRING DIAGRAMs and check the starter motor power circuit for short circuit to ground, open circuit, high resistance. Repair the wiring harness or install a new starter motor as necessary
- Check that the engine turns freely. Rectify as necessary
|
| The engine does not crank (starter motor does turn) |
- Starter motor incorrectly installed
- Starter motor internal failure
- Flywheel/drive plate ring gear damaged
|
- Check the installation of the starter motor. Rectify as necessary
- Check the operation of the starter motor. Rectify as necessary
- Check the flywheel/drive plate ring gear teeth for damage, foreign objects, etc. Rectify as necessary
|
| Engine cranks too slowly |
- Battery/charging system fault
- Starter motor ground circuit open circuit, high resistance
- Starter motor power circuit open circuit, high resistance
- Starter motor internal failure
- Engine oil grade incorrect
|
- Refer to the relevant service information and check the battery and charging system. Rectify as necessary
- Refer to the applicable SYSTEM WIRING DIAGRAMs and check the starter motor ground circuit for open circuit, high resistance. Repair the wiring harness as necessary
- Refer to the applicable SYSTEM WIRING DIAGRAMs and check the starter motor power circuit for open circuit, high resistance. Repair the wiring harness as necessary
- Check the operation of the starter motor. Rectify as necessary
- Check the engine oil grade. Rectify as necessary
|
| Engine cranks too fast |
- Timing chain failure
- Engine cylinder compressions too low
|
- Check the integrity of the timing chain. Rectify as necessary
- Refer to the relevant service information and check the engine cylinder compressions. Rectify as necessary
|
| Starter motor excessively noisy |
- Starter motor incorrectly installed Starter motor internal failure
- Flywheel/drive plate ring gear damaged
|
- Check the installation of the starter motor. Rectify as necessary Check the operation of the starter motor. Rectify as necessary
- Check the flywheel/drive plate ring gear teeth for damage, foreign objects, etc. Rectify as necessary
|
| Auto stop/start system inoperative |
- Auto stop/start system inhibited
- Driver error/expectation
- Recent DTC clear
- System fault
- Auto stop/start system fault
|
NOTE:
'AUTO STOP/START FAULT' will be displayed in the instrument cluster message centre when the system is inoperative due to a fault.
- Refer to the AUTO STOP/START SYSTEM INHIBITS table for possible inhibit conditions.
- Auto stop/start system inhibited due to driver error/expectation: Explain/demonstrate the auto stop/start system to the driver
- Auto stop/start system inhibited due to a recent DTC clear (and a drive cycle not completed): Road test the vehicle at a speed of 48 to 80 km/h (30 to 50 mph) for 2 to 3 minutes, allow the engine to idle, auto stop/start will now activate
- Auto stop/start system inhibited due to battery condition: Using the Jaguar Land Rover approved diagnostic equipment, perform routine - Power Supply Service Mode Diagnostic Routine
- Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index
|