LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2015 >> XFR-S >> Repair and Diagnosis >> External Pages >> Different car >> Section 79 (Engine - V6 S/C 3.0L Petrol -- XF/X250) >> Engine - V6 S/C 3.0L Petrol >> Right Cylinder Head (G1557017) >> Removal And Installation >> Installation

Removal And Installation: Installation

WARNING: This page is about a different car, the 2015 Jaguar XF, 2014 Jaguar XF, and 2013 Jaguar XF. However, it is still accessible from the selected car via links, so may be relevant.
  1. CAUTION: An acceptable flatness of the cylinder head is 0.1mm.

    Check cylinder head face for distortion, across the center and from corner to corner.

  2. WARNING: Make sure care is taken when handling the cylinder head gasket.
    CAUTION:
    • The head gasket must be installed over the cylinder block dowels.
    • Make sure that the mating faces are clean and free of foreign material.
    NOTE: Install a new cylinder head gasket.
    G11415616
  3. CAUTION: Make sure that new cylinder head bolts are installed.
    NOTE: Tighten the bolts in the indicated sequence.
    G11415617

    Torque Specification: 20 Nm 

  4. NOTE: Tighten the bolts in the indicated sequence.
    G11415618

    Torque Specification: 35 Nm 

  5. NOTE: Slacken the bolts in the indicated sequence.
    G11415619
  6. NOTE: Tighten the bolts in the indicated sequence.
    G11415620

    Torque Specification: 35 Nm 

  7. NOTE: Tighten the bolts in the indicated sequence.
    G11415621

    Tighten the bolts 1 to 8, a further 90 degrees.

  8. NOTE: Tighten the bolts in the indicated sequence.
    G11415622

    Tighten the bolts 1 to 8, a further 120 degrees.

  9. G11415623

    Torque Specification: 25 Nm 

  10. NOTE: Tighten the bolts in the indicated sequence.
    G11415624

    Torque Specification: 12 Nm 

  11. CAUTION:
    • If a new cylinder head has been installed then new tappets must be installed.
    • If the cylinder head is being removed without a new component being installed, the tappets must be installed in their original positions.
    NOTE:
    • Some variation in the illustrations may occur, but the essential information is always correct.
    • Left-hand shown, right-hand similar.
    G11415625

    Lubricate the valve tappets with clean engine oil.

  12. NOTE: Install a new gasket.
    G11415626

    Torque Specification: 12 Nm 

  13. CAUTION: A new O-ring seal is to be installed.
    NOTE: Install a new engine oil filter.
    G11415627
  14. G11415628

    Torque Specification: 25 Nm 

  15. G11415629

    Torque Specification: 10 Nm 

  16. CAUTION: Install the new seals.
    G11415630

    Torque Specification: 10 Nm 

  17. G11415631
  18. G11415632

    Torque Specification: 20 Nm 

  19. Refer to: Right Camshaft  (Engine - V6 S/C 3.0L Petrol, Removal and Installation).
  20. Refer to: Right Exhaust Manifold  (Engine - V6 S/C 3.0L Petrol, Removal and Installation).

  21. Refer to: Secondary Bulkhead Right Panel - TDV6 3.0L Diesel/V6 S/C 3.0L Petrol/V8 S/C 5.0L Petrol (Front End Body Panels, Removal and Installation).

  22. Refer to: Battery Disconnect and Connect (Battery, Mounting and Cables, General Procedures).
scientia non olet · About LEMON Manuals