LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> Suspension >> Wheels & Tire System >> Wheels & Tires -- XK/X150 >> Wheels And Tires >> Tire Pressure Monitoring System >> Diagnosis And Testing >> Pinpoint Tests >> Pinpoint Test E: Right Rear Low Frequency Initiator Circuit

Pinpoint Test E: Right Rear Low Frequency Initiator Circuit

  1. E1: CHECK THE INITIATOR CIRCUIT FOR SHORT CIRCUIT TO GROUND 
    1. Ignition off.
    2. Disconnect the right hand rear low-frequency initiator electrical connector, C4MC43.
    3. Measure the resistance between:
    G11504227
    C4MC43, HARNESS SIDE BATTERY
    Pin 2 Negative terminal

    Is the resistance less than 10, 000 Ohms?

    • Yes  : GO to  E5.
    • No  : GO to  E2.
  2. E2: CHECK THE INITIATOR CIRCUIT FOR SHORT CIRCUIT TO POWER 
    1. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 2 Positive terminal

    Is the resistance less than 10, 000 Ohms?

    • Yes  : GO to  E6.
    • No  : GO to  E3.
  3. E3: CHECK THE INITIATOR CIRCUIT FOR SHORT CIRCUIT TO GROUND 
    1. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 1 Negative terminal

    Is the resistance less than 10, 000 Ohms?

    • Yes  : GO to  E7.
    • No  : GO to  E4.
  4. E4: CHECK THE INITIATOR CIRCUIT FOR SHORT CIRCUIT TO POWER 
    1. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 1 Positive terminal

    Is the resistance less than 10, 000 Ohms?

    • Yes  : GO to  E8.
    • No  : GO to  E9.
  5. E5: CHECK WHETHER THE SHORT CIRCUIT IS IN THE HARNESS OR THE MODULE 
    1. Disconnect the Tire Pressure Monitoring System module connector, C3MC39A.
    2. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 2 Negative terminal
      G11504228

    Is the resistance less than 10, 000 Ohms?

    • Yes  : REPAIR the short circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No  : INSTALL a new Tire Pressure Monitoring System module. Refer to:

      Tire Pressure Monitoring System Module - Convertible  (Removal and Installation),

      Tire Pressure Monitoring System Module - 2-Door  (Removal and Installation).

  6. E6: CHECK WHETHER THE SHORT CIRCUIT IS IN THE HARNESS OR THE MODULE 
    1. Disconnect the Tire Pressure Monitoring System module connector, C3MC39A.
    2. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 2 Positive terminal
    G11504228

    Is the resistance less than 10, 000 Ohms?

    • Yes  : REPAIR the short circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No  : INSTALL a new Tire Pressure Monitoring System module. Refer to:

      Tire Pressure Monitoring System Module - Convertible  (Removal and Installation),

      Tire Pressure Monitoring System Module - 2-Door  (Removal and Installation).

  7. E7: CHECK WHETHER THE SHORT CIRCUIT IS IN THE HARNESS OR THE MODULE 
    1. Disconnect the Tire Pressure Monitoring System module connector, C3MC39A.
    2. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 1 Negative terminal
      G11504228

    Is the resistance less than 10, 000 Ohms?

    • Yes  : REPAIR the short circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No  : INSTALL a new Tire Pressure Monitoring System module. Refer to:

      Tire Pressure Monitoring System Module - Convertible  (Removal and Installation),

      Tire Pressure Monitoring System Module - 2-Door  (Removal and Installation).

  8. E8: CHECK WHETHER THE SHORT CIRCUIT IS IN THE HARNESS OR THE MODULE 
    1. Disconnect the Tire Pressure Monitoring System module connector, C3MC39A.
    2. Measure the resistance between:
      C4MC43, HARNESS SIDE BATTERY
      Pin 1 Positive terminal
      G11504228

    Is the resistance less than 10, 000 Ohms?

    • Yes  : REPAIR the short circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No  : INSTALL a new Tire Pressure Monitoring System module. Refer to:

      Tire Pressure Monitoring System Module - Convertible  (Removal and Installation),

      Tire Pressure Monitoring System Module - 2-Door  (Removal and Installation).

  9. E9: CHECK THE INITIATOR CIRCUIT FOR HIGH RESISTANCE 
    1. Measure the resistance between:
      C3MC39A, HARNESS SIDE C4MC43, HARNESS SIDE
      Pin 8 Pin 2

    Is the resistance greater than 5 Ohms?

    • Yes  : REPAIR the high resistance circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No: GO to  E10.
  10. E10: CHECK THE INITIATOR CIRCUIT FOR HIGH RESISTANCE 
    1. Measure the resistance between:
      C3MC39A, HARNESS SIDE C4MC43, HARNESS SIDE
      Pin 7 Pin 1

    Is the resistance greater than 5 Ohms?

    • Yes  : REPAIR the high resistance circuit. This circuit contains intermediate connector, C44-Y. For additional information, refer to the wiring diagram. Clear the DTC and run an On Demand Self Test (ODST) using the manufacturer approved diagnostic system to confirm rectification.
    • No  : INSTALL a new rear right hand low-frequency initiator. Refer to: Tire Pressure Monitoring System Rear Antenna .