Instrument Panel Cluster (IPC)

WARNING: This page is about a different car, the 2011 Jaguar XKR, 2011 Jaguar XK, 2010 Jaguar XKR, and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle

CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00

NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component

NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer approved diagnostic system)

NOTE: When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account

NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests

NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion

NOTE: If DTCs are recorded and, after performing the pinpoint tests a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals

NOTE: Where an 'on demand self-test' is referred to, this can be accessed via the 'DTC Monitor' tab on the manufacturers approved diagnostic system

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the instrument panel cluster, for additional diagnosis and testing information refer to the relevant diagnosis and testing. For additional information, refer to: INSTRUMENT CLUSTER .

DTC	Description	Possible Cause	Action
B1008-11	Wiper mode switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the wiper switch circuits for short to ground. Clear diagnostic trouble code and retest Repair wiring harness or replace switch as required. Clear diagnostic trouble code and retest
B1008-15	Wiper mode switch - circuit short to power or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the wiper switch circuits for short circuit to power, open circuit, high resistance. Clear diagnostic trouble code and retest Repair wiring harness or replace switch as required. Clear diagnostic trouble code and retest
B1009-51	Ignition authorisation - not programmed	Faulty instrument cluster Re-synchronisation error following programming CAN fault	Refer to the electrical circuit diagrams and check the ignition, power and ground connections to central junction box and instrument cluster Re-synchronise ID by re-configuring the instrument cluster as a new module. Clear diagnostic trouble code and retest Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the instrument cluster and the central junction box
B1009-62	Ignition authorisation - signal compare failure	Central junction box fault Instrument cluster fault Low speed CAN fault Incorrect module installed (central junction box/instrument cluster) Re-synchronisation error following re-programming Noise/electromagnetic compatibility related error	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster Confirm correct central junction box/instrument cluster module is installed Re-synchronise ID by re-configuring the instrument cluster as a new module. Clear diagnostic trouble code and retest Check CAN network for interference/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B1009-87	Ignition authorisation - missing message	Central junction box fault Instrument cluster fault Low battery voltage < 9 volts Low speed CAN fault	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Check battery is fully charged and in serviceable condition, refer to the battery care manual Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest
B100A-62	Fuel pump authorisation - signal compare failure	Central junction box fault Instrument cluster fault Low speed CAN fault Incorrect module installed (central junction box/instrument cluster) Module ID synchronisation error following re-programming Noise/electromagnetic compatibility related error	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster Confirm correct central junction box/instrument cluster module installed Re-synchronise ID by re-configuring the central junction box as a new module Check CAN network for interference/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B100A-64	Fuel Pump authorisation - signal plausibility failure	Module ID synchronisation error following re-programming Central junction box fault Low speed CAN fault Low speed CAN fault	Re-synchronise ID by re-configuring the central junction box as a new module Refer to the electrical circuit diagrams and check the ignition, power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster
B100A-87	Fuel pump authorisation - missing message	Central junction box fault Instrument cluster fault Low battery voltage < 9 volts Low speed CAN fault	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Check battery is fully charged and in serviceable condition, refer to the battery care manual Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest
B100B-67	Column lock ground authorisation - signal incorrect after event	Central junction box fault Instrument cluster fault Low speed CAN fault Vehicle speed present when attempting to power steering column lock Engine speed present when attempting to power steering column lock Power mode status > 4 when attempting to perform lock action	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest Check ABS module, engine control module and central junction box for diagnostic trouble codes and refer to the relevant diagnostic trouble code index
B100B-87	Column lock ground authorisation - missing message	Central junction box fault Instrument cluster fault Low speed CAN fault	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest
B100C-67	Column lock supply authorisation - signal incorrect after event	Central junction box fault Instrument cluster fault Low speed CAN fault Vehicle speed present when attempting to power steering column lock Engine speed present when attempting to power steering column lock Power mode status > 4 when attempting to perform lock action	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest Check ABS module, engine control module and central junction box for diagnostic trouble codes and refer to the relevant diagnostic trouble code index
B100C-87	Column lock supply authorisation - missing message	Central junction box fault Instrument cluster fault Low speed CAN fault	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and instrument cluster. Clear diagnostic trouble code and retest
B100D-62	Column lock authorisation - signal compare failure	Steering column lock fault Instrument cluster fault CAN fault Incorrect module installed (Steering column lock/instrument cluster) Target ID synchronisation error following re-programming Noise/electromagnetic compatibility related error	Refer to the electrical circuit diagrams and check the power and ground connections to the steering column lock and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the steering column lock and instrument cluster. Clear diagnostic trouble code and retest Confirm the correct steering column lock/instrument cluster modules are installed Re-synchronize ID by re-configuring the steering column lock as new Check CAN network for interference/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B100D-64	Column lock authorisation - signal plausibility failure	Steering column lock fault Instrument cluster fault CAN fault	Refer to the electrical circuit diagrams and check the power and ground connections to the steering column lock and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the steering column lock and instrument cluster. Clear diagnostic trouble code and retest
B100D-87	Column Lock Authorisation - Missing message	Missing message CAN fault No response from electric steering column lock control module, instrument cluster, central junction box Battery voltage at electric steering column lock control module too low Electric steering column lock control module, instrument cluster, central junction box fault	Clear DTC, repeatedly lock and unlock car using the key fob and retest. Check for related DTCs and refer to the relevant DTC index If the fault is cleared, notify the customer that the steering column lock may fail to unlock if the vehicle is parked with a high steering angle or with the road wheel against a curb. If the column lock is failing to disengage, the customer may be able to rectify this by rotating the steering wheel while pressing the engine start button If fault persists, complete a CAN network integrity test using the manufacturers approved diagnostic system. Alternatively, refer to the electrical circuit diagrams and check CAN circuits between the central junction box, the instrument cluster and the electronic steering column lock. Refer to the electrical circuit diagrams and check the central junction box, the instrument cluster and the electronic steering column lock power and ground supply circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit(s) as required. Clear DTC, perform an on demand self-test and retest If fault persists, check that the vehicle battery supply voltage is between 9-16 volts. Rectify as required
B100D-96	Column Lock Authorisation - Component internal failure	Battery voltage at electric steering column lock control module too low Torque load on steering column CAN fault Electric steering column lock control module - Internal failure	Clear DTC, repeatedly lock and unlock car using the key fob and retest If fault persists, check that the vehicle battery supply voltage is between 9-16 volts. Rectify as required Ensure the column lock bolt movement is not obstructed or restricted (the parked position of the road wheels may be exerting a turning force through the steering column, preventing the lock from releasing. The steering wheel may need to be held against the force to allow the column lock to release). Clear DTC, repeatedly lock and unlock car using the key fob and retest If fault persists, complete a CAN network integrity test using the manufacturers approved diagnostic system. Alternatively, refer to the electrical circuit diagrams and check CAN circuits between the central junction box, the instrument cluster and the electronic steering column lock. Refer to the electrical circuit diagrams and check the central junction box, the instrument cluster and the electronic steering column lock power and ground supply circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit(s) as required. Clear DTC, perform an on demand self-test and retest If fault persists, check and install a new electric steering column lock control module as required
B1024-87	Start Control Unit - missing message	Loss of LIN communication with start control unit Start control unit failure	Refer to the electrical circuit diagrams and check the power and ground connections to the start control unit. Refer to circuit diagrams and check LIN bus circuits. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new start control unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1048-11	Brake Fluid Level Switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the brake fluid level switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B10A0-11	Wiper/washer switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the wiper/washer switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B10A0-15	Wiper/washer switch - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the wiper/washer switch circuits for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B10A6-11	Main light switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the main light switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B10A6-15	Main light switch - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the main light switch circuits for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B10AC-87	Cruise control switch - missing message	Loss of LIN communication with speed control module Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Switch fault Internal module fault	Refer to the electrical circuit diagrams and check the power and ground connections to the speed control module. Using the manufacturer approved diagnostic system, complete a LIN network integrity test Refer to the electrical circuit diagrams and check the LIN network between the speed control module and instrument panel cluster control module If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest If diagnostic trouble code persists, check and install new speed control module. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B112B-87	Steering Wheel Module - missing message	Loss of LIN communication with steering wheel module Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Switch fault Internal module fault	Refer to the electrical circuit diagrams and check the power and ground connections to the steering wheel module. Using the manufacturer approved diagnostic system, complete a LIN network integrity test Refer to the electrical circuit diagrams and check the LIN network between the steering wheel module and instrument panel cluster control module If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest If diagnostic trouble code persists, check and install new steering wheel module. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B115C-7A	Transfer fuel pump - fluid leak or seal failure	Fluid leak or seal failure	Check transfer fuel pump for leak/seal failure
B1A85-11	Ambient light sensor - circuit short to ground	Wiring harness fault - short circuit to ground Sensor fault	Refer to electrical circuit diagrams and check the sunlight sensor circuit for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest Check and install new sensor as required. Clear diagnostic trouble code and retest
B1A85-15	Ambient light sensor - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Sensor fault	Refer to electrical circuit diagrams and check the sunlight sensor circuit for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest Check and install new sensor as required. Clear diagnostic trouble code and retest
B1B01-00	Key transponder - number of keys stored below minimum number required	Operator only cycles one key during programming Instrument cluster, start control unit or key loses power or circuit failure during programming Faulty key Unable to programme key due to noise/electromagnetic compatibility related issues	Ensure all keys to be programmed are available Check power and ground supplies to instrument cluster, start control unit. Clear diagnostic trouble code and retest Check and replace faulty key as required Check CAN network for noise/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B1B01-05	Key transponder - system programming failures	Error following start control unit replacement Start control unit fault Instrument cluster fault LIN fault	Re-synchronize ID by re-configuring the start control unit as a new module Refer to the electrical circuit diagrams and check the power and ground connections to the start control unit and instrument cluster Refer to the electrical circuit diagrams and check the LIN network between the start control unit and instrument cluster
B1B01-51	Key transponder - not programmed	Instrument cluster fault Start control unit fault LIN fault Faulty key Attempted to programme a non-default key	Refer to the electrical circuit diagrams and check the power and ground connections to the start control unit and the instrument cluster Refer to the electrical circuit diagrams and check the LIN network between the start control unit and instrument cluster. Clear diagnostic trouble code and retest Ensure new keys are from a known good source
B1B01-55	Key transponder - not configured	Un-programmed key inserted in start control unit Non-default key inserted during key programming	Confirm correct keys are being used
B1B01-62	Key transponder - signal compare failure	Instrument cluster fault Start control unit fault Incorrect module installed (instrument cluster/start control unit) Error during or following the module ID check routine Noise/electromagnetic compatibility related issues	Refer to the electrical circuit diagrams and check the power and ground connections to the start control unit and the instrument cluster Check correct instrument cluster/start control unit modules are installed Re-synchronize ID by re-configuring the start control unit as a new module Check CAN network for interference/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B1B01-64	Key transponder - signal plausibility failure	Instrument cluster fault Start control unit fault LIN fault Key fault Error occurred during key programming	Refer to the electrical circuit diagrams and check the power and ground connections to the start control unit and the instrument cluster Refer to the electrical circuit diagrams and check the LIN network between the start control unit and instrument cluster. Clear diagnostic trouble code and retest Confirm correct key operation Re-run key programming
B1B01-67	Key transponder - signal incorrect after event	Instrument cluster fault Key fault Start control unit fault LIN fault Another key in close proximity Attempted to programme a non default key Instrument panel cluster cold initialisation whilst in ignition-on state, without key being present in the start control unit Race condition caused by closing driver door and pressing start button within a small time window Passive key search function from last door closed and key inserted in the start control unit	Refer to the electrical circuit diagrams and check the ignition, power and ground connections to the start control unit and the instrument cluster Refer to the electrical circuit diagrams and check the LIN network between the start control unit and instrument cluster. Clear diagnostic trouble code and retest Confirm single key operation Confirm correct key operation Ensure new keys are from a known good source Check for intermittent power and ground at instrument cluster If no wiring, electrical or key fault evident, determine customer transponder key usage and advise customer of correct starting sequence
B1B01-87	Key transponder - missing message	Instrument cluster fault Start control unit fault LIN fault	Refer to the electrical circuit diagrams and check the ignition, power and ground connections to the start control unit and the instrument cluster Refer to the electrical circuit diagrams and check the LIN network between the start control unit and instrument cluster. Clear diagnostic trouble code and retest
B1B33-05	Target I.D. transfer - system programming failures	Engine control module fault Instrument cluster fault CAN fault Engine control module or instrument cluster incorrectly configured	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and instrument cluster. Clear diagnostic trouble code and retest Re-synchronise ID by re-configuring the instrument cluster as a new module
B1B33-62	Target I.D. transfer - signal compare failure	Engine control module fault Instrument cluster fault CAN fault Incorrect module installed (Engine control module/instrument cluster) Module ID synchronisation error following re-programming Noise/electromagnetic compatibility related error	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and instrument cluster. Clear diagnostic trouble code and retest Check correct engine control module and instrument cluster installed Re-synchronise module ID by reconfiguring the instrument cluster as a new module Check CAN network for interference/electromagnetic compatibility related issues. Ensure that the vehicle is away from sources of electromagnetic interference prior to clearing diagnostic trouble codes and retesting
B1B33-64	Target I.D. transfer - signal plausibility failure	Engine control module fault Instrument cluster fault CAN fault Steering column lock status incomplete Race condition caused by closing driver door and pressing start button within a small time window	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and instrument cluster. Clear diagnostic trouble code and retest Check steering column lock operation If no wiring or electrical fault evident, advise customer of correct starting sequence
B1B33-87	Target I.D. transfer - missing message	Engine control module fault Instrument cluster fault CAN fault Low battery voltage	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module and instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and instrument cluster. Clear diagnostic trouble code and retest Check battery is in fully charged and serviceable condition, refer to the battery care manual
B1C32-77	Steering column tilt solenoid - commanded position not reachable	Tilt motion mechanical fault Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Switch fault	Check mechanical functions of steering column and solenoid pin Refer to electrical circuit diagrams and check the tilt solenoid and switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C32-94	Steering column tilt solenoid - unexpected operation	Tilt motion mechanical fault Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Switch fault	Check mechanical functions of steering column and solenoid pin Refer to electrical circuit diagrams and check the tilt solenoid and switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C33-12	Steering column tilt feedback signal - circuit shorted to battery	Wiring harness fault - short circuit to power	Refer to electrical circuit diagrams and check the tilt feedback circuits for short circuit to power. Repair wiring harness as required. Clear diagnostic trouble code and retest
B1C33-14	Steering column tilt feedback signal - circuit short to ground or open	Wiring harness fault - short circuit to ground, open circuit, high resistance	Refer to electrical circuit diagrams and check the tilt feedback circuits for short circuit to ground, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest
B1C34-77	Steering column telescope solenoid - commanded position not reachable	Telescope motion mechanical fault Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Solenoid fault Switch fault	Check mechanical functions of column and solenoid pin Refer to electrical circuit diagrams and check the telescope solenoid and switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new solenoid or switch as required. Clear diagnostic trouble code and retest
B1C34-94	Steering column telescope solenoid - unexpected operation	Telescope motion mechanical fault Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance Solenoid fault Switch fault	Check mechanical functions of column and solenoid pin Refer to electrical circuit diagrams and check the telescope solenoid and switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new solenoid or switch as required. Clear diagnostic trouble code and retest
B1C35-12	Steering column telescope feedback signal - circuit shorted to battery	Wiring harness fault - short circuit to power	Refer to electrical circuit diagrams and check the telescope feedback circuits for short circuit to power. Repair wiring harness as required. Clear diagnostic trouble code and retest
B1C35-14	Steering column telescope feedback signal - circuit short to ground or open	Wiring harness fault - short circuit to ground, open circuit, high resistance	Refer to electrical circuit diagrams and check the telescope feedback circuits for short circuit to ground, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest
B1C36-11	Steering column tilt/telescope switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the steering column tilt/telescope switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C48-11	Flash to pass switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the flash to pass switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C48-15	Flash to pass switch - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the flash to pass switch circuits for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C53-11	Front wiper intermittent data - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the intermittent wiper switch circuit for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1C53-15	Front wiper intermittent data - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the intermittent wiper switch circuit for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1D36-11	Turn indicator switch - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the turn switch circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1D36-15	Turn indicator switch - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the turn switch circuits for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1D37-11	Wiper switch connection circuit - circuit short to ground	Wiring harness fault - short circuit to ground Switch fault	Refer to electrical circuit diagrams and check the flick wiper switch connection circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
B1D37-15	Wiper switch connection circuit - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch fault	Refer to electrical circuit diagrams and check the flick wiper switch connection circuits for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch as required. Clear diagnostic trouble code and retest
C004A-11	Brake Lining Wear Sensor - circuit short to ground	Wiring harness fault - short circuit to ground Brake pad wear sensor fault	Refer to electrical circuit diagrams and check the brake pad wear sensor circuit for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new sensor as required. Clear diagnostic trouble code and retest
C004A-15	Brake Lining Wear Sensor - circuit short to battery or open	Wiring harness fault - short circuit to power, open circuit, high resistance Brake pad wear sensor fault	Refer to electrical wiring diagrams and check the brake pad wear sensor circuit for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new sensor as required. Clear diagnostic trouble code and retest
C1110-64	Power steering calibration data - signal plausibility failure	Invalid variable assistance power steering calibration loaded	Using the manufacturer approved diagnostic system, re-configure the instrument cluster as new. Reload variable assistance power steering calibration data
P0610-55	Control Module Vehicle Options Error - not configured	Central junction box incorrectly configured	Configure the central junction box using the manufacturer's approved diagnostic system
P0635-11	Power steering control circuit - circuit short to ground	Wiring harness fault - short circuit to ground Variable assistance power steering actuator fault	Refer to electrical circuit diagrams and check the variable assistance power steering control circuits for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new variable assistance power steering actuator as required. Clear diagnostic trouble code and retest
P0635-12	Power steering control circuit - circuit short to battery	Wiring harness fault - short circuit to power Variable assistance power steering actuator fault	Refer to electrical circuit diagrams and check the variable assistance power steering control circuits for short circuit to power. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new variable assistance power steering actuator as required. Clear diagnostic trouble code and retest
P0635-13	Power steering control circuit - circuit open	Wiring harness fault - open circuit, high resistance Variable assistance power steering actuator fault	Refer to electrical circuit diagrams and check the variable assistance power steering control circuits for open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new variable assistance power steering actuator as required. Clear diagnostic trouble code and retest
P0635-22	Power steering control circuit - signal amplitude > maximum	Wiring harness fault - short circuit to ground, short circuit to power, open circuit, high resistance CAN fault Internal fault within instrument cluster	Refer to electrical circuit diagrams and check the variable assistance power steering actuator control circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest Refer to the electrical circuit diagrams and check the power and ground connections to the instrument cluster. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Clear diagnostic trouble code and retest If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0635-44	Power steering control circuit - data memory failure	Internal fault within instrument cluster module	Refer to the electrical circuit diagrams and check for intermittent faults on the power and ground connections to the instrument cluster. Repair wiring harness as required. Clear diagnostic trouble code and retest If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U0001-88	High speed CAN communication Bus - bus off	High speed CAN failure - bus off	Refer to the electrical circuit diagrams and check the high speed CAN bus for short circuit to ground, short circuit to power, open circuit, high resistance
U0010-88	Medium speed CAN communication Bus - bus off	Medium speed CAN failure - bus off	Refer to the electrical circuit diagrams and check the medium speed CAN bus for short circuit to ground, short circuit to power, open circuit, high resistance
U0100-00	Lost communication with ECM/PCM A - missing message	Loss of CAN communication with engine control module	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and the instrument cluster Check the engine control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0101-00	Lost communication with TCM - missing message	Loss of CAN communication with transmission control module	Refer to the electrical circuit diagrams and check the power and ground connections to the transmission control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the transmission control module and the instrument cluster Check the transmission control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0103-00	Lost communication with Gear Shift Module - missing message	Loss of CAN communication with transmission shift module	Refer to the electrical circuit diagrams and check the power and ground connections to the transmission shift module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the transmission shift module and the instrument cluster Check the transmission shift module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0104-00	Lost communication with cruise control module - missing message	Loss of CAN communication with speed control module	Refer to the electrical circuit diagrams and check the power and ground connections to the speed control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the speed control module and the instrument cluster Check the speed control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0121-00	Lost communication with Anti-lock Brake System (ABS) control module - missing message	Loss of CAN communication with ABS control module	Refer to the electrical circuit diagrams and check the power and ground connections to the ABS control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the ABS control module and the instrument cluster Check the ABS control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0126-00	Lost Communication With Steering Angle Sensor Module - missing message	Loss of CAN communication with steering angle sensor module	Refer to the electrical circuit diagrams and check the power and ground connections to the steering angle sensor module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the steering angle sensor module and the instrument cluster Check the steering angle sensor module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0127-00	Lost communication with Tire Pressure Monitor Module - missing message	Loss of CAN communication with tire pressure monitor module	Refer to the electrical circuit diagrams and check the power and ground connections to the tire pressure monitor module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the tire pressure monitor module and the instrument cluster Check the tire pressure monitor module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0128-00	Lost communication with Park Brake control module - missing message	Loss of CAN communication with the park brake control module	Refer to the electrical circuit diagrams and check the power and ground connections to the park brake control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the park brake control module and the instrument cluster Check the park brake control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0139-00	Lost communication with Adaptive Damping Control Module - missing message	Loss of communication with continuously variable damping module	Refer to the electrical circuit diagrams and check the power and ground connections to the continuously variable damping module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the continuously variable damping module and the instrument cluster Check the continuously variable damping module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0140-00	Lost communication with Body Control Module - missing message	Loss of CAN communication with central junction box	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and the instrument cluster Check the central junction box for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0142-00	Lost communication with Body Control Module B - missing message	Loss of CAN communication with auxiliary junction box	Refer to the electrical circuit diagrams and check the power and ground connections to the auxiliary junction box Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the auxiliary junction box and the instrument cluster Check the auxiliary junction box for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0151-00	Lost communication with Restraints Control Module - missing message	Loss of CAN communication with restraints control module	Refer to the electrical circuit diagrams and check the power and ground connections to the restraints control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the restraints control module and the instrument cluster Check the restraints control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0156-00	Lost communication with Infotainment Control Module - missing message	Loss of CAN communication with information and entertainment control module	Refer to the electrical circuit diagrams and check the power and ground connections to the information and entertainment control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the information and entertainment control module and the instrument cluster Check the information and entertainment control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0164-00	Lost communication with HVAC - missing message	Loss of CAN communication with climate control module	Refer to the electrical circuit diagrams and check the power and ground connections to the climate control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the climate control module and the instrument cluster Check the climate control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U017E-00	Lost communication with Seatbelt Pretensioner module A - missing message	Loss of CAN communication with driver seatbelt pretensioner module	Refer to the electrical circuit diagrams and check the power and ground connections to the driver seatbelt pretensioner module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the driver seatbelt pretensioner module and the instrument cluster Check the driver seatbelt pretensioner module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U017F-00	Lost communication with Seatbelt Pretensioner module B - missing message	Loss of CAN communication with passenger seatbelt pretensioner module	Refer to the electrical circuit diagrams and check the power and ground connections to the passenger seatbelt pretensioner module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the passenger seatbelt pretensioner module and the instrument cluster Check the passenger seatbelt pretensioner module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0199-00	Lost communication with Driver Door Module - missing message	Loss of CAN communication with driver door module	Refer to the electrical circuit diagrams and check the power and ground connections to the driver door module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the driver door module and the instrument cluster Check the driver door module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0200-00	Lost communication with Passengers Door Module - missing message	Loss of CAN communication with passenger door module	Refer to the electrical circuit diagrams and check the power and ground connections to the passenger door module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the passenger door module and the instrument cluster Check the passenger door module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0206-00	Lost communication with Folding Top Control Module - missing message	Loss of CAN communication with convertible top module	Refer to the electrical circuit diagrams and check the power and ground connections to the convertible top module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the convertible top module and the instrument cluster Check the convertible top module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0208-00	Lost communication with Driver Seat Module - missing message	Loss of CAN communication with driver seat module	Refer to the electrical circuit diagrams and check the power and ground connections to the driver seat module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the driver seat module and the instrument cluster Check the driver seat module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0209-00	Lost communication with Passenger Seat Module (PSM) Control Module - missing message	Loss of CAN communication with passenger seat module	Refer to the electrical circuit diagrams and check the power and ground connections to the passenger seat module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the passenger seat module and the instrument cluster Check the passenger seat module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0214-00	Lost communication with Keyless Vehcile Module - missing message	Loss of CAN communication with keyless vehicle module	Refer to the electrical circuit diagrams and check the power and ground connections to the keyless vehicle module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the keyless vehicle module and the instrument cluster Check the keyless vehicle module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0241-00	Lost communication with Headlamp Control Module 'A' - missing message	Loss of CAN communication with headlamp control module	Refer to the electrical circuit diagrams and check the power and ground connections to the headlamp control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the headlamp control module and the instrument cluster Check the headlamp control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0250-00	Lost communication with PIE - missing message	Loss of CAN communication with pedestrian protection module	Refer to the electrical circuit diagrams and check the power and ground connections to the pedestrian protection module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the pedestrian protection module and the instrument cluster Check the pedestrian protection module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0256-00	Lost communication with Integrated Control Panel - missing message	Loss of CAN communication with integrated control panel	Refer to the electrical circuit diagrams and check the power and ground connections to the integrated control panel Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the integrated control panel and the instrument cluster Check the integrated control panel for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U0300-00	Internal Control Module software incompatibility - no sub type information	Central junction box car configuration data is not compatible with the instrument cluster	Re-configure the central junction box using the manufacturer approved diagnostic system. Clear diagnostic trouble codes and re-test If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U0402-68	Invalid data received from TCM - algorithm based failures/events information	Invalid data received from transmission control module	Check the transmission control module for related diagnostic trouble codes and refer to the relevant diagnostic trouble code index
U2004-11	Auxiliary switch pack - circuit short to ground	Wiring harness fault - short circuit to ground Switch pack fault	Refer to electrical circuit diagrams and check the auxiliary switch pack signal circuit for short circuit to ground. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch pack as required. Clear diagnostic trouble code and retest
U2004-15	Auxiliary switch pack - circuit short to power or open	Wiring harness fault - short circuit to power, open circuit, high resistance Switch pack fault	Refer to electrical circuit diagrams and check the auxiliary switch pack signal circuit for short circuit to power, open circuit, high resistance. Repair wiring harness as required. Clear diagnostic trouble code and retest If no circuit faults are present, check and install new switch pack as required. Clear diagnostic trouble code and retest
U3000-46	Control module - calibration/parameter memory failure	Instrument cluster internal fault - corrupt non-volatile memory	Clear diagnostic trouble code and retest. If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U3000-49	Control module - internal electronic failure	Instrument cluster internal fault - ROM/EEPROM checksum failure	Clear diagnostic trouble code and retest. If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U3000-55	Control module - not configured	Incorrect car configuration data received	Re-configure the central junction box using the manufacturer approved diagnostic system. Clear diagnostic trouble code and re-test If fault persists, check and install a new instrument cluster. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component/component
U3000-87	Control module - missing message	Car configuration parameter not received	Re-configure the central junction box using the manufacturer approved diagnostic system. Clear diagnostic trouble code and re-test Check instrument cluster for diagnostic trouble codes and refer to the diagnostic trouble code index Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and the instrument cluster
U3002-81	Vehicle Identification Number - invalid serial data received	Vehicle/component mis-match. Corrupt VIN data being transmitted, module previously installed to other vehicle	Install original module, check for diagnostic trouble codes and refer to relevant diagnostic trouble code index
U3003-16	Battery voltage - circuit voltage below threshold	Circuit voltage < 9 volts threshold	Refer to relevant information and battery care manual. Check battery state of charge and starting/charging system performance
U3003-17	Battery voltage - circuit voltage above threshold	Circuit voltage > 16 volts threshold	Refer to relevant informaiton and battery care manual. Check battery state of charge and starting/charging system performance
U3003-62	Battery voltage - signal compare failure	Signal compare failure Instrument cluster voltage differs more than ±2V compared to central electronics module voltage	Refer to relevant information and battery care manual. Check battery state of charge and starting/charging system performance. Check logic power supply circuit from central junction box to instrument cluster Refer to electrical circuit diagrams and check the power and ground supply circuits to the module. Repair wiring harness as required. Clear diagnostic trouble code and retest