LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Fuel Charging & Controls (V8 5.0L Petrol)) >> Fuel Charging And Controls (V8 5.0L Petrol) >> Removal And Installation >> Right-Hand Fuel Rail High-Pressure Fuel Pump >> Installation

Right-Hand Fuel Rail High-Pressure Fuel Pump: Installation

WARNING: This page is about a different car, the 2011 Jaguar XK and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.

    All vehicles 

    NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with clean engine oil.
  1. See figure
    GJ0012868
    2. CAUTION: Tighten the Torx screws a turn at a time until the correct torque is achieved.
    NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal with clean engine oil.
  2. Torque: 12 Nm
    GJ0012856
  3. Loosen the Torx screws half a turn each.
    GJ0012856
  4. See figure
    GJ0012869
    5. CAUTION: Install new high-pressure fuel supply lines.
    CAUTION: Lubricate only  the union threads with clean engine oil.
    NOTE: Engine shown removed for clarity.
    NOTE: Remove and discard the blanking caps.
    NOTE: Install the bolt and unions fully finger tight before final tightening.
  5. See figure
    GJ0012991
    6. CAUTION: Care must be taken when positioning the fuel rail high-pressure fuel pump cover to one side.
    NOTE: Fuel rail high-pressure fuel pump cover shown removed for clarity.
  6. Torque: 12 Nm
    GJ0012856
  7. Lower the vehicle.
    8. NOTE: Do not tighten at this stage.
    NOTE: Remove and discard the blanking caps.
  8. See figure
    GJ0012992
    9. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.
  9. Raise and support the vehicle.
    10. NOTE: Engine shown removed for clarity.
  10. Torque:

    Unions (1) 21 Nm

    M6 (2) 11 Nm

    M8 (3) 25 Nm

    M5 nut (4) 6 Nm

    GJ0012873
    11. NOTE: Engine shown removed for clarity.
  11. Torque: 21 Nm
    GJ0012872
    12. NOTE: Install the bolt and unions finger tight before final tightening.
    NOTE: Remove and discard the blanking caps.
  12. Torque:

    Unions 21 Nm

    M6 11 Nm

    GJ0012995
  13. Torque: 21 Nm
    GJ0012996
    14. NOTE: Engine shown removed for clarity.
  14. Torque:

    M10 29 Nm

    M6 11 Nm

    GJ0012994
    15. NOTE: Engine shown removed for clarity.
  15. See figure
    GJ0012875
  16. Torque: 25 Nm
    GJ0012137

    17. Left-hand drive vehicles 

  17. Torque: 100 Nm
    GJ0023208
  18. Torque: 35 Nm
    GJ0023207

    19. All vehicles 

  19. Refer to Generator information.
  20. Refer to ENGINE MOUNT RH information.
  21. Lower the vehicle.
  22. See figure
    GJ0012850
    23. NOTE: Lubricate the union threads with clean engine oil.
    NOTE: Do not tighten at this stage.
    NOTE: Remove and discard the blanking caps.
  23. See figure
    GJ0012819
  24. Torque:

    Unions 21 Nm

    Bolts 8 Nm

    GJ0012819
  25. Torque: 21 Nm
    GJ0012832
  26. Refer to Right Air Cleaner Outlet Intermediate Pipe information.
  27. See figure
    GJ0022932
  28. See figure
    GJ0013229
  29. Refer to Battery Disconnect and Connect information.
  30. Refer to Engine Oil Draining and Filling information.
  31. Refer to Engine Cover - 5.0L information.
scientia non olet · About LEMON Manuals