LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Fuel Charging & Controls (V8 5.0L Petrol)) >> Fuel Charging And Controls (V8 5.0L Petrol) >> Removal And Installation >> Fuel Rail RH >> Removal

Fuel Rail RH: Removal

WARNING: This page is about a different car, the 2011 Jaguar XK and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Removal steps in this procedure may contain installation details.
  1. Refer to Petrol and Petrol-Ethanol Fuel Systems Health and Safety Precautions information.
  2. Refer to Fuel System Pressure Release - V8 5.0L Petrol/V8 S/C 5.0L Petrol information.
  3. Refer to Battery Disconnect and Connect information.
  4. Refer to Fuel Injection Component Cleaning or Fuel Injection Component Cleaning .
  5. Refer to Cowl Vent Screen information.
  6. See figure
    GJ0025274
  7. See figure
    GJ0025492
  8. See figure
    GJ0022932
  9. See figure
    GJ0013229
  10. Refer to Right Air Cleaner Outlet Intermediate Pipe information.
    11. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  11. See figure
    GJ0012819
  12. See figure
    GJ0012850
    13. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  13. See figure
    GJ0012987
    14. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.
  14. Raise and support the vehicle.
    GJ0012875
    15. NOTE: Engine shown removed for clarity.
  15. See figure
    GJ0012994
    16. NOTE: Engine shown removed for clarity.
  16. See figure
    GJ0012988
    17. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
    NOTE: Engine shown removed for clarity.
  17. Lower the vehicle.
    GJ0012989
  18. See figure
    GJ0012970
    19. NOTE: LH shown RH similar.
  19. See figure
    20. NOTE: LH shown RH similar.
  20. See figure
    GJ0012971
  21. Spark Plug Remover/Installer (303-1450)
    GJ0012972
    22. CAUTION: Make a note of the fuel injector alignment to the fuel rail prior to removal.
    NOTE: LH shown RH similar.
  22. See figure
    GJ0012973
    23. CAUTION: Make sure that the special tool is located correctly to the fuel injector prior to removing the fuel injector.
    CAUTION: Make sure that the special tool is held square to the fuel injector during removal.
    CAUTION: Make sure that all open ports are covered to prevent any foreign material ingress.
  23. Remover, Fuel Injector (310-197)
    GJ0012990
    24. CAUTION: If the fuel injector is being removed without a new component being installed, the fuel injector clamp must remain with the fuel injector it is removed with.
  24. See figure
    GJ0012975
    25. CAUTION: Do not use a knife to remove the Teflon seal as damage could occur to the fuel injector.
    CAUTION: Do not cut the Teflon seal to deep as damage could occur to the fuel injector.
    CAUTION: Pinch the Teflon seal to allow the tool to cut the Teflon seal without damaging the fuel injector.
  25. See figure
    GJ0012976
    26. CAUTION: Do not use any sharp tools to remove the O-ring seal as damage could occur to the fuel injector.
  26. See figure
    GJ0012977
scientia non olet · About LEMON Manuals