LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Fuel Charging & Controls (V8 5.0L Petrol)) >> Fuel Charging And Controls (V8 5.0L Petrol) >> Removal And Installation >> Fuel Rail LH >> Removal

Fuel Rail LH: Removal

WARNING: This page is about a different car, the 2011 Jaguar XK and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Make sure that tools and equipment are clean, free of foreign material and lubricant.
NOTE: Removal steps in this procedure may contain installation details.
  1. Refer to Petrol and Petrol-Ethanol Fuel Systems Health and Safety Precautions information.
  2. Refer to Fuel System Pressure Release - V8 5.0L Petrol/V8 S/C 5.0L Petrol information.
  3. Refer to Battery Disconnect and Connect information.
  4. Refer to Fuel Injection Component Cleaning or Fuel Injection Component Cleaning .
  5. Refer to Cowl Vent Screen information.
  6. Torque: 45 Nm
    GJ0025490
  7. See figure
    GJ0025491
  8. See figure
    GJ0022932
    9. CAUTION: Be prepared to collect escaping fluids.
  9. See figure
    GJ0022933
  10. See figure
    GJ0013229
  11. Refer to RIGHT AIR CLEANER OUTLET INTERMEDIATE PIPE information.
    12. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  12. See figure
    GJ0012819
  13. See figure
    GJ0012850
    14. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  14. See figure
    GJ0012987
    15. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.
  15. Raise and support the vehicle.
    16. NOTE: Engine shown removed for clarity.
  16. See figure
    GJ0012875
    17. NOTE: Engine shown removed for clarity.
  17. See figure
    GJ0012994
    18. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
    NOTE: Engine shown removed for clarity.
  18. See figure
    GJ0012988
  19. Lower the vehicle.
  20. See figure
    GJ0012970
  21. See figure
    GJ0012971
    22. NOTE: RH shown LH similar.
  22. Spark Plug Remover/Installer (303-1450)
    GJ0012972
    23. CAUTION: Make a note of the fuel injector clamp alignment to the fuel rail prior to removal.
  23. See figure
    GJ0012973
    24. CAUTION: Make sure that the special tool is located correctly to the fuel injector prior to removing the fuel injector.
    CAUTION: Make sure that the special tool is held square to the fuel injector during removal.
    CAUTION: Make sure that all open ports are covered to prevent any foreign material ingress.
  24. Remover, Fuel Injector (310-197)
    GJ0012974
    25. CAUTION: If the fuel injector is being removed without a new component being installed, the fuel injector clamp must remain with the fuel injector it is removed with.
  25. See figure
    GJ0012975
    26. CAUTION: Do not use a knife to remove the Teflon seal as damage could occur to the fuel injector.
    CAUTION: Do not cut the Teflon seal to deep as damage could occur to the fuel injector.
    CAUTION: Pinch the Teflon seal to allow the tool to cut the Teflon seal without damaging the fuel injector.
  26. See figure
    GJ0012976
    27. CAUTION: Do not use any sharp tools to remove the O-ring seal as damage could occur to the fuel injector.
  27. See figure
    GJ0012977
scientia non olet · About LEMON Manuals