LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 15 (Automatic Transmission/Transaxle (V8 5.0L Petrol/V8 S/C 5.0L Petrol)) >> Automatic Transmission/Transaxle (V8 5.0L Petrol/V8 S/C 5.0L Petrol) >> Diagnostic Procedures >> Diagnostic Flow Chart >> DTC Index

DTC Index

WARNING: This page is about a different car, the 2011 Jaguar XKR, 2011 Jaguar XK, 2010 Jaguar XKR, and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00.
NOTE: If the control module/transmission is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module/transmission.
NOTE: Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the scan tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give additional information read by the manufacturer approved diagnostic system).
NOTE: When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
DTC Description Possible Cause Action
P0121-86 Throttle/Pedal Position Sensor A Circuit Range/Performance - signal invalid
  • Throttle/Pedal Position Sensor Fault (Data received over CAN Bus)
 Check Engine Control Module for stored DTCs
P0219-86 Engine Overspeed Condition - signal invalid
  • Engine speed too low or too high (Data received over CAN Bus)
 Check Engine Control Module for stored DTCs
P0500-81 Vehicle Speed Sensor A - invalid serial data received
  • Vehicle Speed Sensor fault (Data received over CAN Bus)
 Check DSC module for stored DTCs
P0501-81 Vehicle Speed Sensor A Range/Performance invalid serial data received
  • Vehicle Speed receive over CAN Bus does not match Transmission Output-Shaft speed
 Check Anti-lock braking system module for stored DTCs. Check correct Differential is installed to the vehicle
P0561-1C System Voltage Unstable - Circuit voltage out of range
  • Power supply voltage out of range when engine running
 Check Engine control module for stored DTCs. Check Charging System and Battery condition
P0562-21 System Voltage Low - signal amplitude < minimum
  • Circuit low voltage. Battery supply voltage to Transmission Control Module (Transmission control module)
 Refer to Circuit diagrams and check Power and Ground Circuit for fault. Check Engine control module for stored DTCs. Check Charging System and Battery condition
P0563-22 System Voltage High - signal amplitude > maximum
  • High Battery charge, alternator fault
 Check Engine control module for stored DTCs. Check Charging System and Battery condition
P0601-41 Internal Control Module Memory Check Sum Error - general checksum failure
  • Software error
  • Transmission control module failure
 Re-configure the Transmission control module using the manufacturer approved diagnostic system, clear DTC and re-test. If DTC remains, Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0604-00 Internal Control Module Random Access Memory (RAM) Error - no sub type information
  • Shift-by-Wire fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0605-41 Internal Control Module Read Only Memory (ROM) Error - general checksum failure
  • General checksum failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0606-04 Transmission control module Processor - System Internal Failures
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0606-26 Transmission control module Processor - signal rate of change below threshold
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0606-49 Transmission control module Processor-internal electronic failure
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-04 Transmission control module Processor - System Internal Failures
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-06 Transmission control module Processor - Algorithm Based Failures
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-11 Transmission control module Processor - Circuit Short to Ground
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-12 Transmission control module Processor - Circuit Short to Battery
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-13 Transmission control module Processor - Circuit Open
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-14 Transmission control module Processor - Circuit Short to Ground or Open
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-21 Transmission control module Processor - signal amplitude < minimum
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-22 Transmission control module Processor - signal amplitude > maximum
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-47 Transmission control module Processor - watchdog / safety Micro controller failure
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-49 Transmission control module Processor - internal electronic failure
  • Micro controller component faults
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0613-68 Transmission control module Processor-Event Information
  • Watchdog fault
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P061B-02 Internal Control Module Torque Calculation Performance - general signal failure
  • Transmission control module - positive torque signal not valid
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P061B-26 Internal Control Module Torque Calculation Performance - signal rate of change below threshold
  • Transmission control module positive torque signal not valid
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P062F-04 Internal Control Module EEPROM Error - System Internal Failures
  • EEPROM communication error
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0642-21 Sensor Reference Voltage A Circuit Low - signal amplitude < minimum
  • Sensor supply voltage fault low
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0643-22 Sensor Reference Voltage A Circuit High - signal amplitude > maximum
  • Sensor supply voltage fault high
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0657-13 Actuator Supply Voltage A Circuit / Open - Circuit Open
  • Actuator supply (pressure control valves etc) Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0657-1C Actuator Supply Voltage A Circuit / Open - Circuit voltage out of range
  • Actuator supply (pressure control valves etc) voltage plausibility fault
 Refer to electrical Circuit diagrams and check Transmission control module connector for signs of water ingress or damage, check pin 7 for Short to Power or Ground (should NOT be connected and harness terminal should have a bung fitted). If no fault identified, suspect the Transmission control module. Check and install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0658-11 Actuator Supply Voltage A Circuit Low - Circuit Short to Ground
  • Actuator supply (pressure control valves etc) voltage Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0659-12 Actuator Supply Voltage A Circuit High - Circuit Short to Battery
  • Actuator supply (pressure control valves etc) voltage Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0667-01 PCM / Engine control module / Transmission control module Internal Temperature Sensor A Range/Performance - General Electrical Failure
  • General electrical failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0667-04 PCM / Engine control module / Transmission control module Internal Temperature Sensor A Range/Performance - System Internal Failures
  • Internal Electronic Failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0667-49 PCM / Engine control module / Transmission control module Internal Temperature Sensor A Range/Performance - internal electronic failure
  • Internal electronic failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0700-02 Transmission Control System (MIL Request) - General signal failure
  • General Signal failure
 Clear DTC, Road test and re-test, Read DTCs and Investigate as required
P0700-22 Transmission Control System (MIL Request) - signal amplitude > maximum
  • Double fault from monitoring of internal power supply and pressure regulator/solenoid control software
 If any of the following DTCs are also present; P074013, P096712, P273912, P273012, P272112, P096312, P276312, P097112, suspect the Transmission control module, check and install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0700-75 Transmission Control System (MIL Request) - Emergency Position Not Reachable
  • Emergency Position Not Reachable
 Clear DTC, Road test and re-test, Read DTCs and investigate as required
P0710-13 Transmission Fluid Temperature Sensor A Circuit - Circuit Open
  • Transmission fluid temperature sensor Circuit Open Circuit
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0711-01 Transmission Fluid Temperature Sensor A Circuit Range/Performance - General Electrical Failure
  • General electrical failure
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0711-22 Transmission Fluid Temperature Sensor A Circuit Range/Performance - signal amplitude > maximum
  • Signal amplitude > maximum. Excessive jump in temperature
 Clear DTC. Carry out cold start road test, continue driving vehicle until normal operating temperature is achieved. Reads DTCs, if DTC returns, suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0712-11 Transmission Fluid Temperature Sensor A Circuit Low - Circuit Short to Ground
  • Transmission fluid temperature sensor Circuit Short to Ground
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0713-01 Transmission Fluid Temperature Sensor A Circuit High-General Electrical Failure
  • General electrical failure
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0713-12 Transmission Fluid Temperature Sensor A Circuit High - Circuit Short to Battery
  • Transmission fluid temperature sensor Circuit Short to Power
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0716-14 Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Circuit Short to Ground or Open
  • Turbine/Input Shaft Speed Sensor Circuit Short to Ground or Open Circuit
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0716-21 Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - signal amplitude < minimum
  • Turbine/Input Shaft Speed Sensor signal too small
 Clear DTC and road test, if DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0716-22 Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - signal amplitude > maximum
  • Turbine/Input Shaft Speed Sensor signal above maximum
 Clear DTC and road test, if DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0717-12 Turbine/Input Shaft Speed Sensor A Circuit No Signal - Circuit Short to Battery
  • Turbine/input shaft speed sensor A Circuit Short to Power
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0720-12 Output Shaft Speed Sensor Circuit - Circuit Short to Battery
  • Transmission output shaft speed sensor Circuit Short to Power
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0720-14 Output Shaft Speed Sensor Circuit - Circuit Short to Ground or Open
  • Transmission output shaft speed sensor Circuit Short to Ground or Open Circuit
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0721-22 Output Shaft Speed Sensor Circuit Range/Performance - signal amplitude > maximum
  • Transmission output shaft speed sensor signal above maximum
 Clear DTC and road test, if DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0721-27 Output Shaft Speed Sensor Circuit Range/Performance - signal rate of change above threshold
  • Output shaft speed negative gradient too high
 Clear DTC and road test, if DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0721-64 Output Shaft Speed Sensor Circuit Range/Performance - signal plausibility failure
  • Signal plausibility failure
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0731-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0732-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0733-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0734-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0735-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0736-07 Incorrect Gear Ratio-Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0740-13 Torque Converter Clutch Solenoid Circuit / Open - Circuit Open
  • Pressure control solenoid 2 Circuit Open Circuit
 Clear DTC and test. If code re-detects suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0741-07 Torque Converter Clutch Solenoid Circuit Performance/Stuck Off - Mechanical Failures
  • Too high slip at torque converter clutch. Mechanical Failures
 Suspect torque converter lockup clutch. Install a new torque converter, refer to the new module/component installation note at the top of the DTC Index. If transmission fluid is in very poor condition and dirty, install a new transmission, refer to the new module/component installation note at the top of the DTC Index
P0745-04 Pressure Control Solenoid A - System Internal Failures
  • System Internal Failures
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0745-48 Pressure Control Solenoid A - Supervision Software Failure
  • Supervision Software Failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0758-12 Shift Solenoid B Electrical - Circuit Short to Battery
  • Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0758-13 Shift Solenoid B Electrical - Circuit Open
  • Solenoid valve 1 or Pressure control Solenoid G Circuit Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0771-71 Shift Solenoid E Performance/Stuck Off - actuator stuck
  • Actuator stuck
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0775-04 Pressure Control Solenoid B - System Internal Failures
  • System Internal Failures
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0775-48 Pressure Control Solenoid B - Supervision Software Failure
  • Supervision Software Failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0781-07 1-2 Shift - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0781-77 2-1 Shift - commanded position not reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0782-07 2-3 Shift - commanded position not reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0782-77 3-2 Shift - commanded position not reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0783-07 3-4 Shift - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0783-77 3-4 Shift - commanded position not reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0784-07 4-5 Shift - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0784-77 4-5 Shift - commanded position not reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0798-1A Pressure Control Solenoid C Electrical - Circuit Resistance Below Threshold
  • Pressure control solenoid C Circuit resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0798-1E Pressure Control Solenoid C Electrical - Circuit Short to Ground
  • Pressure control solenoid C electrical circuit short to ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0798-21 Pressure Control Solenoid C Electrical - signal amplitude < minimum
  • Pressure Control Solenoid C Electrical signal amplitude < minimum
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0814-62 Transmission Range Display Circuit - signal compare failure
  • Transmission Range Display Circuit signal compare failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0826-08 Up and Down Switch circuit - Bus Signal Message Failures
  • Invalid CAN signal from BCM/Instrument cluster
  • Stuck switch
  • CAN bus circuit fault
 Check Central junction box and Instrument cluster for stored DTCs. Check gear change switches for correct operation. Refer to circuit diagrams and check CAN bus for a circuit fault
P0826-81 Up and Down Switch Circuit - invalid serial data received
  • Invalid Can signal from BCM / Instrument cluster
  • Stuck switch
  • CAN Bus Circuit fault
 Check Central junction box and Instrument cluster for stored DTCs. Check Gear Change Switches for correct operation. Refer to Circuit diagrams and check CAN Bus for Circuit fault
P0826-88 Up and Down Switch Circuit - Bus off
  • SWM to BCM / Instrument cluster LIN Bus failure
 Check Central junction box and Steering Wheel Ice Switches for stored DTCs. Refer to Circuit diagrams and check LIN Bus for Circuit fault
P0829-07 5-6 Shift - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P0829-77 6-5 Shift - Commanded Position Not Reachable
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P084F-01 Park / Neutral Switch Input Circuit - General Electrical Failure
  • Wrong voltage level detected on Park/No Park signal
 Check for correct output at Transmission control module park signal pin (check in all positions) 12 volts in Park, 0 volts in all other positions. If fault identified, suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index. If no fault identified, check Park signal circuit to Transmission Shift Module for short, open circuit.
P0850-01 Park / Neutral Switch Input Circuit - General Electrical Failure
  • General electrical failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0850-02 Park / Neutral Switch Input Circuit - General signal failure
  • General signal failure
 Check park lock mechanism. If park lock operation is correct, suspect the transmission control module. Check and install a new transmission control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component
P0850-29 Park / Neutral Switch Input Circuit - signal invalid
  • Signal invalid
 Check park lock mechanism. If park lock operation is correct, suspect the transmission control module. Check and install a new transmission control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component
P850-1C Park / Neutral Switch Input Circuit - circuit voltage out of range
  • Circuit voltage out of range
 Check park lock mechanism, if park lock operation correct suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0919-93 Gear Shift Position Control Error - no operation
  • No shifting despite driver request
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0919-94 Gear Shift Position Control Error - unexpected operation
  • Shifting without driver request
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0938-29 Hydraulic Oil Temperature Sensor Range/Performance - signal invalid
  • Transmission fluid temperature compared with module temperature fault
 Clear DTC. Carry out cold start road test, continue driving vehicle until normal operating temperature is achieved. Read DTCs, if DTC returns, suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0963-12 Pressure Control Solenoid A Control Circuit High - Circuit Short to Battery
  • Pressure control solenoid 1 Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0964-13 Pressure Control Solenoid B Control Circuit / Open - Circuit Open
  • Pressure Control Solenoid B Control Circuit Open
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0964-14 Pressure Control Solenoid B Control Circuit / Open - Circuit Short to Ground or Open
  • Pressure Control Solenoid B Control Circuit Short to Ground or Open
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0966-11 Pressure Control Solenoid B Control Circuit Low - Circuit Short to Ground
  • Pressure control solenoid 2 Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0967-12 Pressure Control Solenoid B Control Circuit High - Circuit Short to Battery
  • Pressure control solenoid 2 Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0968-14 Pressure Control Solenoid C Control Circuit / Open - Circuit Short to Ground or Open
  • Pressure control solenoid 3 Circuit Short to Ground or Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0970-11 Pressure Control Solenoid C Control Circuit Low - Circuit Short to Ground
  • Pressure control solenoid 3 Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0971-12 Pressure Control Solenoid C Control Circuit High - Circuit Short to Battery
  • Pressure control solenoid 3 Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0972-22 Shift Solenoid A Control Circuit Range/Performance - signal amplitude > maximum
  • Pressure control solenoid 1 current too large
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0973-11 Shift Solenoid A Control Circuit Low - Circuit Short to Ground
  • Shift solenoid A control Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0973-14 Shift Solenoid A Control Circuit Low - Circuit Short to Ground or Open
  • Pressure control solenoid 1 Circuit Short to Ground or Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0973-1A Shift Solenoid A Control Circuit Low - Circuit Resistance Below Threshold
  • Shift Solenoid A control circuit resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0973-1E Shift Solenoid A Control Circuit Low - Circuit Resistance Out Of Range
  • Shift Solenoid A control circuit resistance out of range
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0976-11 Shift Solenoid B Control Circuit Low - Circuit Short to Ground
  • Solenoid valve 2 Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P0976-14 Shift Solenoid B Control Circuit Low - Circuit Short to Ground or Open
  • Solenoid valve 2 Circuit Short to Ground or Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P1674-04 Control Module Software Corrupted - System Internal Failures
  • System internal failures
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P1674-48 Control Module Software Corrupted - Supervision Software Failure
  • Supervision software failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P1707-07 Transfer Case Neutral or Park/Neutral Indication Circuit - commanded position not reachable
  • Transfer case neutral or park/neutral indication circuit - mechanical failures
 Clear the DTC. Test drive the Vehicle, engaging and disengaging the parking lock several times. If the DTC recurs, check parking lock components and replace as required. If no faulty park lock component is found Clear DTC and the DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P1707-72 Transfer Case Neutral or Park/Neutral Indication Circuit - Actuator Stuck Open
  • Transfer case neutral or park/neutral indication circuit - Actuator stuck open
 Clear the DTC. Test drive the Vehicle, engaging and disengaging the parking lock several times. If the DTC recurs, check parking lock components and replace as required. If no faulty park lock component is found Clear DTC and the DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P1707-77 Transfer Case Neutral or Park/Neutral Indication Circuit - commanded position not reachable
  • Commanded position not reachable
 Clear the DTC. Test drive the Vehicle, engaging and disengaging the parking lock several times. If the DTC recurs, check parking lock components and replace as required. If no faulty park lock component is found Clear DTC and the DTC returns suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2700-07 Transmission Friction Element A Apply Time Range/Performance - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P2701-07 Transmission Friction Element B Apply Time Range/Performance - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P2702-07 Transmission Friction Element C Apply Time Range/Performance - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P2703-07 Transmission Friction Element D Apply Time Range/Performance - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P2704-07 Transmission Friction Element E Apply Time Range/Performance - Mechanical Failures
  • Gear Ratio Monitoring. Mechanical Failures
 Check and correct oil level. Clear DTC. If code re-detects suspect Transmission (Gearbox) internal fault. Install a new Transmission as required, refer to the new module/component installation note at the top of the DTC Index
P2713-04 Pressure Control Solenoid D - System Internal Failures
  • System internal failures
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2713-48 Pressure Control Solenoid D - Supervision Software Failure
  • Supervision software failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2716-22 Pressure Control Solenoid D Electrical - signal amplitude > maximum
  • Pressure Control Solenoid D Electrical signal amplitude > maximum
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2716-1A Pressure Control Solenoid D Electrical - Circuit Resistance Below Threshold
  • Pressure control solenoid D circuit resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2716-1E Pressure Control Solenoid D Electrical - Circuit Resistance Out Of Range
  • Pressure control solenoid D circuit resistance out of range
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2718-14 Pressure Control Solenoid D Control Circuit / Open - Circuit Short to Ground or Open
  • Pressure control solenoid D Circuit Short to Ground or Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2720-11 Pressure Control Solenoid D Control Circuit Low - Circuit Short to Ground
  • Pressure control solenoid D Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2721-12 Pressure Control Solenoid D Control Circuit High - Circuit Short to Battery
  • Pressure control solenoid D Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2722-04 Pressure Control Solenoid E - System Internal Failures
  • Pressure Control Solenoid E system internal failures
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2722-48 Pressure Control Solenoid E - Supervision Software Failure
  • Pressure Control Solenoid E supervision control software failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2725-22 Pressure Control Solenoid E Electrical - signal amplitude > maximum
  • Pressure Control Solenoid E Electrical signal amplitude > maximum
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2725-1A Pressure Control Solenoid E Electrical - Circuit Resistance Below Threshold
  • Pressure control solenoid E electrical resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2725-1E Pressure Control Solenoid E Electrical - Circuit Resistance Out Of Range
  • Pressure control solenoid E circuit resistance out of range
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2727-14 Pressure Control Solenoid E Control Circuit / Open - Circuit Short to Ground or Open
  • Pressure Control Solenoid E Control Circuit Short to Ground or Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2729-11 Pressure Control Solenoid E Control Circuit Low - Circuit Short to Ground
  • Pressure control solenoid E Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2730-12 Pressure Control Solenoid E Control Circuit High-Circuit Short to Battery
  • Pressure control solenoid E Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2731-04 Pressure Control Solenoid F-System Internal Failures
  • Pressure Control Solenoid F no sub type information
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2731-48 Pressure Control Solenoid F - Supervision Software Failure
  • Pressure Control Solenoid F supervision software failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2734-22 Pressure Control Solenoid F Electrical-signal amplitude > maximum
  • Pressure Control Solenoid F Electrical signal amplitude > maximum
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2734-1A Pressure Control Solenoid F Electrical-Circuit Resistance Below Threshold
  • Pressure control solenoid F electrical circuit resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2734-1E Pressure Control Solenoid F Electrical-Circuit Resistance Out Of Range
  • Pressure control solenoid F electrical circuit resistance out of range
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2736-14 Pressure Control Solenoid F Control Circuit / Open - Circuit Short to Ground or Open
  • Pressure Control Solenoid F Control Circuit Short to Ground or Open
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2738-11 Pressure Control Solenoid F Control Circuit Low - Circuit Short to Ground
  • Pressure Control Solenoid F Control Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2739-12 Pressure Control Solenoid F Control Circuit High - Circuit Short to Battery
  • Pressure Control Solenoid F Control Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2763-12 Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit Short to Battery
  • Pressure control solenoid F Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2764-11 Torque Converter Clutch Pressure Control Solenoid Control Circuit Low - Circuit Short to Ground
  • Torque converter clutch pressure control solenoid control Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2764-1A Torque Converter Clutch Pressure Control Solenoid Control Circuit Low-Circuit Resistance Below Threshold
  • Torque converter clutch pressure control solenoid control circuit resistance below threshold
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2764-1E Torque Converter Clutch Pressure Control Solenoid Control Circuit Low-Circuit Resistance Out Of Range
  • Torque converter clutch pressure control solenoid control circuit resistance out of range
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2807-11 Pressure Control Solenoid G - Circuit Short to Ground
  • Park solenoid Circuit Short to Ground
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2807-12 Pressure Control Solenoid G - Circuit Short to Battery
  • Park solenoid Circuit Short to Power
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2807-13 Pressure Control Solenoid G - Circuit Open
  • Park solenoid Circuit Open Circuit
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
P2807-14 Pressure Control Solenoid G - Circuit Short to Ground or Open
  • Park solenoid Circuit Short to Ground or Open Circuit
 Carry out any diagnostic pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
B1087-82 LIN Bus "A" - alive / sequence counter incorrect / not updated
  • Alive counter fault
 Check Transmission Shift Module for stored DTCs. Refer to the electrical Circuit diagrams and check Transmission control module to Transmission Shift Module for Short to Ground or Open Circuit (LIN Bus)
B1087-83 LIN Bus "A" - value of signal protection calculation incorrect
  • Checksum error
 Check Transmission Shift Module for stored DTCs Refer to the electrical Circuit diagrams and check Transmission control module to Transmission Shift Module for Short to Ground or Open Circuit (LIN Bus)
B1087-87 LIN Bus "A" - missing message
  • GSM is NOT visible to the Transmission control module on the LIN Bus
 Check Transmission Shift Module for stored DTCs Refer to the electrical Circuit diagrams and check Transmission control module to Transmission Shift Module for Short or Open Circuit (LIN Bus)
B1087-88 LIN Bus "A" - Bus off
  • LIN Bus Circuit fault. Check hardware of LIN connection between transmission and GSM
 Refer to the electrical Circuit diagrams and check Transmission control module to Transmission shift module for Short, Open Circuit (LIN Bus). Check Transmission Shift Module for related DTCs
U0001-88 High Speed CAN Communication Bus - Bus off
  • CAN Bus off
 Refer to the electrical Circuit diagrams and check CAN Bus for Circuit fault
U0100-82 Lost Communication With Engine control module/PCM "A" - alive / sequence counter incorrect / not updated
  • Alive counter fault
 Check Engine control module for stored DTCs
U0100-83 Lost Communication With Engine control module/PCM "A" - value of signal protection calculation incorrect
  • Checksum fault
 Check Engine control module for stored DTCs
U0100-87 Lost Communication With Engine control module/PCM "A" - missing message
  • CAN Timeout
NOTE: Do NOT install a new Engine control module if an Engine control module Timeout DTC is only logged in the Transmission control module, the failure is NOT with the Engine control module
Check Engine control module for stored DTCs. Check CAN Bus Circuit for fault
U0103-82 Lost Communication With Gear Shift Control Module A-alive / sequence counter incorrect / not updated
  • Alive counter fault
 Check Transmission shift module for stored DTCs. Check CAN Bus Circuit for fault
U0103-83 Lost Communication With Gear Shift Control Module A - value of signal protection calculation incorrect
  • Checksum fault
 Check Transmission shift module for stored DTCs. Check CAN Bus Circuit for fault
U0103-87 Lost Communication With Gear Shift Control Module A - missing message
  • CAN Timeout
 Check Transmission shift module for stored DTCs. Check CAN Bus Circuit for fault
U0122-82 Lost Communication With Vehicle Dynamics Control Module - alive / sequence counter incorrect / not updated
  • Alive counter fault
 Check Anti-lock braking system for stored DTCs. Check CAN Bus Circuit for fault
U0122-83 Lost Communication With Vehicle Dynamics Control Module - value of signal protection calculation incorrect
  • Checksum fault
 Check Anti-lock braking system for stored DTCs. Check CAN Bus Circuit for fault
U0122-87 Lost Communication With Vehicle Dynamics Control Module - missing message
  • CAN Timeout
 Check Anti-lock braking system for stored DTCs. Check CAN Bus Circuit for fault
U0126-00 Lost Communication With Steering Angle Sensor Module - no sub type information
  • Lost Communication With Steering Angle Sensor Module
 Check Steering angle sensor for stored DTCs. Check CAN Bus Circuit for fault
U0128-87 Lost Communication With Park Brake Control Module - missing message
  • CAN timeout electronic parking brake module
 Check Electronic Parking Brake Module for stored DTCs. Check CAN Bus Circuit for fault
U0140-82 Lost Communication With Body Control Module - alive / sequence counter incorrect / not updated
  • Alive counter fault
 Check Central junction box for stored DTCs. Check CAN Bus Circuit for fault
U0140-83 Lost Communication With Body Control Module - value of signal protection calculation incorrect
  • Checksum fault
 Check Central junction box for stored DTCs. Check CAN Bus Circuit for fault
U0140-87 Lost Communication With Body Control Module - missing message
  • CAN Timeout
 Check Central junction box for stored DTCs. Check CAN Bus Circuit for fault
U0155-87 Lost Communication With Instrument Panel Cluster (Instrument cluster) Control Module - missing message
  • CAN timeout instrument cluster
 Check Instrument cluster for stored DTCs. Check CAN Bus Circuit for fault
U0300-68 Control Module - event information
  • Transmission software does not match vehicle network
 Check Central junction box software level, Check Transmission control module Software level, Update software as required using the manufacturer approved process
U0401-08 Invalid Data Received From Engine control module/PCM A - Bus Signal Message Failures
  • Inaccurate engine speed, torque information
 Check Engine control module for stored DTCs, Check CAN Bus circuit for faults
U0401-68 Invalid Data Received from Engine control module/PCM A - event information
  • Inaccurate engine speed, torque information
 Check Engine control module for stored DTCs. Check CAN Bus Circuit for fault
U0401-86 Invalid Data Received from Engine control module/PCM A - Signal Invalid
  • Inaccurate engine speed, torque information
 Check Engine control module for stored DTCs. Check CAN Bus Circuit for fault
U0404-68 Invalid Data Received from Gear Shift Control Module A - event information
  • Incorrect CAN data received from Transmission shift module
 Check Transmission Shift Module for stored DTCs. Refer to Circuit diagrams and check CAN and LIN Bus for Circuit fault
U0404-81 Invalid Data Received from Gear Shift Control Module A - Invalid Serial Data Received
  • Incorrect LIN data received from Transmission shift module
 Check Transmission Shift Module for stored DTCs. Refer to Circuit diagrams and check CAN and LIN Bus for Circuit fault
U0416-68 Invalid Data Received From Vehicle Dynamics Control Module - event information
  • Event information brake information
 Check Engine control module for stored DTCs. Check CAN Bus Circuit for fault
U0422-68 Invalid Data Received From Body Control Module - event information
  • Event information invalid Power mode information
 Check Central junction box for stored DTCs. Check CAN Bus Circuit for fault
U101B-87 Lost Communication With GSM - Multiple Bus-missing message
  • Missing message lost communication with Transmission Shift Module (multiple Bus)
 Check Transmission Shift Module for stored DTCs. Refer to Circuit diagrams and check CAN and LIN Bus for Circuit fault
U3000-49 Control Module - internal electronic failure
  • Internal electronic failure
 Suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
U3000-4B Control Module - Circuit resistance above threshold
  • Internal electronic failure
 Check and correct oil level. Check hydraulic flow through oil cooler and pipe circuit for restriction or blockage. If no restrictions found, suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
U3000-81 Control Module - invalid serial data received
  • Vehicle or Engine type signal incorrect from BCM or incorrect Transmission control module software installed
 Reflash the Transmission control module using the manufacturer approved process
U3001-94 Control Module Improper Shutdown - unexpected operation
  • Control Module Improper Shutdown (voltage related)
 Check Engine control module For Power (generator) faults. Check Power and Ground Circuit and Battery for fault. Clear DTCs. Road Test. If DTC reoccurs suspect the Transmission control module. Install a new Transmission control module as required, refer to the new module/component installation note at the top of the DTC Index
scientia non olet · About LEMON Manuals