LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 14 (Electronic Engine Controls (V8 5.0L Petrol)) >> Electronic Engine Controls (V8 5.0L Petrol) >> Diagnostic Procedures >> Electronic Engine Controls >> DTC Index

DTC Index

WARNING: This page is about a different car, the 2011 Jaguar XK and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Fuel injector voltage will reach 65Volts during operation and have a high current requirement.
CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00.
NOTE: If the module/component is suspect and the vehicle remains under the Manufacturers warranty, refer to the Warranty Policy and Procedure manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module/component.
NOTE: Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the scan tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give additional information read by the manufacturer-approved diagnostic system).
NOTE: When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
DTC Description Possible Causes Action
B10A2-31 Crash Input - No signal
  • Loss of communication between Restraints Control Module (RCM) and Engine Control Module (ECM)
 Refer to the electrical circuit diagrams and check Restraints Control Module (RCM) Pulse Width Modulated (PWM) SRS signal line circuit, hard wired connection between Engine Control Module (ECM) and Restraints Control Module (RCM) for short to ground, short to power, open circuit. Repair circuit as required, clear DTC and retest system to confirm repair.
B10AC-81 Cruise Control Switch - invalid serial data received
  • The Engine Control Module (ECM) has received an invalid command from the steering wheel switch pack
 Clear the DTC and press all the steering wheel switches, re-check for DTCs. Refer to the electrical circuit diagrams and check the Cruise control switch circuit for open circuit, short to power, short to ground, disconnected. Check and install a new Steering Wheel Module (SWM) as required.
B10AC-82 Cruise Control Switch - alive / sequence counter incorrect / not updated
  • Cruise Buttons alive counter is not incriminating. Which suggests that the LIN bus is faulty
  • Steering Wheel Module (SWM) is not connected
  • Steering Wheel Module (SWM) failure
 Refer to the electrical circuit diagrams and check the Cruise control switch circuit for open circuit, short to power, short to ground, disconnected. Check and install a new Steering Wheel Module (SWM) as required.
B10AC-83 Cruise Control Switch - value of signal protection calculation incorrect
  • Cruise buttons checksum incorrect, incorrect cruise switches fitted to vehicle
 Check and install new cruise switches as required.
B10AC-96 Cruise Control Switch - component internal failure
  • Cruise control switch circuit, open circuit, short to power, short to ground, disconnected
  • Cruise Control Switch failure
  • Steering Wheel Module (SWM) failure
 Check for related DTCs in other Central Junction Box (CJB)s. Refer to the electrical circuit diagrams and check the Cruise control switch circuit for open circuit, short to power, short to ground, disconnected. Check and install a new cruise control switch as required. Check and install a new Steering Wheel Module (SWM) as required.
B10FF-68 Ignition Control - Event information
  • Spark plug(s) fault
  • Wiring harness fault
  • Ignition coil(s) fault
 Refer to repair manual and check spark plug(s) for condition and security. Replace any defective components as required. Refer to electrical wiring diagrams and check ignition coil circuit for intermittent open circuit, short to power, short to ground. Check and install a new coil(s) as required.
B11DB-01 Battery Monitoring Module - General Electrical Failure
  • Charging system fault
  • Battery monitoring signal line circuit fault
  • Vehicle battery fault
 Refer to electrical wiring diagrams and check charging system for faults. Perform any repairs required. Refer to the electrical wiring diagrams and check the Battery Monitoring System (BMS) module circuit for open circuit, short to ground, short to power. Refer to the battery care manual and check and install a new battery.
B11DB-87 Battery Monitoring Module - missing message
  • Battery signal line circuit fault
 Refer to the electrical wiring diagrams and check the Battery Monitoring System (BMS) module circuit for open circuit, short to ground, short to power.
B1206-68 Crash Occurred - event information
  • Engine control Module (ECM) has detected the vehicle has crashed - event information DTC only
 Refer to the electrical circuit diagrams and check the Engine Control Module (ECM) to Restraints Control Module (RCM) circuit for short to ground, short to power, open circuit. Repair circuit as required, clear DTC and retest system to confirm repair.
C0031-00 Left Front Wheel Speed Sensor - No sub type information
  • Invalid data received from Anti-lock Braking System (ABS) module - left front wheel speed signal fault
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
C0034-00 Right Front Wheel Speed Sensor - No sub type information
  • Invalid data received from Anti-lock Braking System (ABS) module - right front wheel speed signal fault
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
C0037-00 Left Rear Wheel Speed Sensor - No sub type information
  • Invalid data received from Anti-lock Braking System (ABS) module - left rear wheel speed signal fault
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
C003A-00 Right Rear Wheel Speed Sensor - No sub type information
  • Invalid data received from Anti-lock Braking System (ABS) module - right rear wheel speed signal fault
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
P0010-13 Intake (A) Camshaft Position Actuator (Bank 1) - circuit open
  • Intake (A) camshaft position actuator (Bank 1) open circuit
  • Engine Control Module (ECM) interface harness open circuit
 Refer to the electrical circuit diagrams and check Intake (A) camshaft position actuator (Bank 1) open circuit for open circuit. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) interface harness for open circuit.
P0013-13 Exhaust (B) Camshaft Position Actuator (Bank 1) - circuit open
  • Exhaust (B) camshaft position actuator (Bank 1) open circuit
  • Engine Control Module (ECM) interface harness open circuit
 Refer to the electrical circuit diagrams and check Exhaust (B) camshaft position actuator (Bank 1) open circuit for open circuit. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) interface harness for open circuit.
P0015-00 Exhaust (B) Camshaft Position Timing - Over-Retarded (Bank 1) - No sub type information
  • Exhaust (B) camshaft position actuator (Bank 1) open circuit, short to ground, short to power
 Check for related DTC code P0365-00. Refer to the electrical circuit diagrams and check Exhaust (B) camshaft position actuator (Bank 1) for open circuit, short to ground, short to power.
P0016-00 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A - No sub type information
  • The relative positions of the crankshaft position sensor and cam timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
 Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly.
P0017-00 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B - No sub type information
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
 Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 1) for open circuit for open circuit, short to ground, short to power. Check for related DTC code P0365-00. Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly.
P0018-00 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor A - No sub type information
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
 Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly.
P0019-00 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor B - No sub type information
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
 Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly.
P001A-13 Intake (A) Cam Profile Control Circuit (Bank 1) - circuit open
  • Camshaft profile switching solenoid bank 1 open circuit
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 for open circuit.
P001B-11 Intake (A) Cam Profile Control Circuit Low (Bank 1) - circuit short to ground
  • Camshaft profile switching solenoid bank 1 circuit short to ground
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short to ground
P001C-12 Intake (A) Cam Profile Control Circuit High (Bank 1) - circuit short to battery
  • Camshaft profile switching solenoid bank 1 circuit short to power
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short to power.
P001D-13 Intake (A) Cam Profile Control Circuit (Bank 2) - circuit open
  • Camshaft profile switching solenoid bank 2 open circuit
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 for open circuit.
P001E-11 Intake (A) Cam Profile Control Circuit Low (Bank 2) - circuit short to ground
  • Camshaft profile switching solenoid bank 2 circuit short to ground
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short to ground
P001F-12 Intake (A) Cam Profile Control Circuit High (Bank 2) - circuit short to battery
  • Camshaft profile switching solenoid bank 2 circuit short to power
 Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short to power.
P0020-13 Intake (A) Camshaft Position Actuator (Bank 2) - circuit open
  • Intake valve solenoid 2 open circuit
 Refer to the electrical circuit diagrams and check intake valve solenoid 2 for open circuit.
P0023-13 Exhaust (B) Camshaft Position Actuator (Bank 2) - circuit open
  • Exhaust (B) Camshaft Position actuator (Bank 2) circuit, open circuit
 Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 2) circuit for open circuit
P0026-72 Intake Valve Control Solenoid Circuit Range/Performance (Bank 1) - actuator stuck open
  • Intake valve solenoid 1 angle less than target
  • Intake valve solenoid 1 slow or not operating
 Check operation of intake valve solenoid 1. Check and install a new intake valve solenoid 1 as required.
P0026-77 Intake Valve Control Solenoid Circuit Range/Performance (Bank 1) - commanded position not reachable
  • Intake valve solenoid 1 angle greater than target
  • Intake valve solenoid 1 not returning to target in time
  • Intake valve solenoid 1 stuck advanced
 Check operation of intake valve solenoid 1. Check and install a new intake valve solenoid 1 as required.
P0027-72 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1) - actuator stuck open
  • Exhaust valve solenoid 1 angle less than target
  • Exhaust valve solenoid 1 slow or not operating
 Check operation of exhaust valve solenoid 1. Check and install a new exhaust valve solenoid 1 as required.
P0027-77 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1) - commanded position not reachable
  • Exhaust valve solenoid 1 angle greater than target
  • Exhaust valve solenoid 1 not returning to target in time
  • Exhaust valve solenoid 1 stuck advanced
 Check operation of exhaust valve solenoid 1. Check and install a new exhaust valve solenoid 1 as required.
P0028-72 Intake Valve Control Solenoid Circuit Range/Performance (Bank 2) - actuator stuck open
  • Intake valve solenoid 2 angle less than target
  • Intake valve solenoid 2 slow or not operating
 Check operation of intake valve solenoid 2. Check and install a new intake valve solenoid 2 as required.
P0028-77 Intake Valve Control Solenoid Circuit Range/Performance (Bank 2) - commanded position not reachable
  • Intake valve solenoid 2 angle greater than target
  • Intake valve solenoid 2 not returning to target in time
  • Intake valve solenoid 2 stuck advanced
 Check operation of intake valve solenoid 2. Check and install a new intake valve solenoid 2 as required.
P0029-72 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 2) - actuator stuck open
  • Exhaust valve solenoid 2 angle less than target
  • Exhaust valve solenoid 2 slow or not operating
 Check operation of exhaust valve solenoid 2. Check and install a new exhaust valve solenoid 2 as required.
P0029-77 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 2) - commanded position not reachable
  • Exhaust valve solenoid 2 angle greater than target
  • Exhaust valve solenoid 2 not returning to target in time
  • Exhaust valve solenoid 2 stuck advanced
 Check operation of exhaust valve solenoid 2. Check and install a new exhaust valve solenoid 2 as required.
P0031-11 HO2S Heater Control Circuit Low (Bank 1, Sensor 1) - circuit short to ground
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit short to ground
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for short to ground.
P0031-13 HO2S Heater Control Circuit Low (Bank 1, Sensor 1) - circuit open
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit, open circuit
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for open circuit.
P0032-12 HO2S Heater Control Circuit High (Bank 1, Sensor 1) - circuit short to battery
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit short to power
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for short to power.
P0036-00 HO2S Heater Control Circuit (Bank 1, Sensor 2) - no sub type information
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-odd heater control circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-odd failure
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 2 (0x03A2). Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor fuse for open circuit. Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-odd as required.
P003C-00 A Camshaft Profile Control Performance /Stuck Off (Bank 1) - no sub type information
  • Oil supply blockage to camshaft profile switching solenoid
  • Catalyst oxygen sensor failure, giving false flag
  • Camshaft profile switching solenoid bank 1 circuit fault
  • Camshaft profile switching solenoid bank 1 fault
 Check for the presence of oil at the camshaft profile switching solenoid. Check for catalyst oxygen sensor related DTCs. Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short to power, short to ground, open circuit. Check and install a new operation camshaft profile switching solenoid bank 1 as required. Clear DTC and road test the vehicle. If fault remains contact Dealer Technical Support before carrying out any further work.
P003E-00 A Camshaft Profile Control Performance/ Stuck Off (Bank 2) - no sub type information
  • Oil supply blockage to camshaft profile switching solenoid
  • Catalyst oxygen sensor failure, giving false flag
  • Camshaft profile switching solenoid bank 2 circuit fault
  • Camshaft profile switching solenoid bank 2fault
 Check for the presence of oil at the camshaft profile switching solenoid. Check for catalyst oxygen sensor related DTCs. Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short to power, short to ground, open circuit. Check and install a new operation camshaft profile switching solenoid bank 2 as required. Clear DTC and road test the vehicle. If fault remains contact Dealer Technical Support before carrying out any further work.
P0051-11 HO2S Heater Control Circuit Low (Bank 2, Sensor 1) - circuit short to ground
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit short to ground
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit for short to ground.
P0051-13 HO2S Heater Control Circuit Low (Bank 2, Sensor 1) - circuit open
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit, open circuit
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit for open circuit.
P0052-12 HO2S Heater Control Circuit High (Bank 2, Sensor 1) - circuit short to battery
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit short to power
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4). Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 2, Sensor 1) circuit for short to power.
P0054-00 HO2S Heater Resistance (Bank 1, Sensor 2) - no sub type information
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-odd heater control circuit short to ground, power, open circuit, high resistance
  • Catalyst oxygen sensor heater circuit control relay circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-odd failure
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1). Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor fuse for open circuit. Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor circuit for short to ground, power, open circuit, high resistance. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-odd as required.
P0056-00 HO2S Heater Control Circuit (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor-even heater control circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-even failure
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 2 (0x03A5). Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-even sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-even, as required.
P0060-00 HO2S Heater Resistance (Bank 2, Sensor 2) - no sub type information
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-odd heater control circuit short to ground, power, open circuit, high resistance
  • Catalyst oxygen sensor heater circuit control relay circuit short to ground, power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-odd failure
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 2 (0x03A5). Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor fuse for open circuit. Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor circuit for short to ground, power, open circuit, high resistance. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-odd as required.
P0069-29 MAP - Barometric Pressure Correlation - signal invalid
  • Manifold Absolute Pressure (MAP) sensor failure
  • Engine Control Module (ECM) internal fault
 Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A). Check for related Manifold Absolute Pressure (MAP) sensor DTCs. Refer to the electrical circuit diagrams and check manifold absolute pressure sensor circuit for short to ground, short to power, open circuit. Check and install new manifold absolute pressure sensor as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0071-21 Ambient Air Temperature Sensor Range/Performance - signal amplitude < minimum
  • Ambient air temperature sensor circuit short to ground, power, open circuit
  • Temperature and manifold absolute pressure sensor circuit short to ground, power, open circuit
  • Ambient air temperature sensor failure
  • Temperature and manifold absolute pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA). Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check temperature and manifold absolute pressure sensor circuit for short to ground, power, open circuit. Check and install a new ambient air temperature sensor as required. Check and install a new temperature and manifold absolute pressure sensor as required.
P0071-22 Ambient Air Temperature Sensor Range/Performance -Signal amplitude > maximum
  • Ambient air temperature sensor circuit short to ground, power, open circuit
  • Temperature and manifold absolute pressure sensor circuit short to ground, power, open circuit
  • Ambient air temperature sensor failure
  • Temperature and manifold absolute pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA). Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check temperature and manifold absolute pressure sensor circuit for short to ground, power, open circuit. Check and install a new ambient air temperature sensor as required. Check and install a new temperature and manifold absolute pressure sensor as required.
P0072-00 Ambient Air Temperature Sensor Circuit Low - no sub type information
  • Ambient air temperature sensor circuit short to ground, open circuit, high resistance
  • Ambient air temperature sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA). Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, open circuit, high resistance. Check and install a new ambient air temperature sensor as required.
P0073-00 Ambient Air Temperature Sensor Circuit High - no sub type information
  • Ambient air temperature sensor ground circuit high resistance, open circuit
  • Ambient air temperature sensor signal circuit short to power
  • Ambient air temperature sensor failure
 Using the manufacturer approved diagnostic system check datalogger signals Ambient Air Temperature Sensor Voltage (0x03BA). Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, high resistance, short to power. Check connector terminals for corrosion or damage. Check and install a new ambient air temperature sensor as required.
P007B-23 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - signal stuck low
  • Charge air cooler temperature sensor circuit poor / intermittent connection
  • Charge air cooler temperature sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE). Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for poor, intermittent connection, check and install a new charge air cooler temperature sensor as required.
P007B-24 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - signal stuck high
  • Charge air cooler temperature sensor circuit short to ground, open circuit
  • Charge air cooler temperature sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE). Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for short to ground, open circuit. Check and install a new charge air cooler temperature sensor as required.
P007B-29 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - signal invalid
  • Charge air cooler temperature sensor circuit short to ground, open circuit, short to power
  • Charge air cooler temperature sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE). Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for short to ground, open circuit, short to power. Check and install a new charge air cooler temperature sensor as required.
P0087-00 Fuel Rail/System Pressure - Too Low - no sub type information
  • Fuel rail pressure sensor circuit short to ground, open circuit, high resistance
  • Fuel rail pressure sensor failure
  • Fuel lines leaking or restricted
  • Fuel pump failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377). Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to ground, open circuit, high resistance. Check for fuel pump related DTCs. Check fuel lines for leakage or restriction. Check and install new fuel rail pressure sensor as required. Check and install a new fuel pump as required.
P0088-00 Fuel Rail/System Pressure - Too High - no sub type information
  • Fuel rail pressure sensor circuit short to each other, high resistance, short to power
  • Fuel rail pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377). Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to each other, high resistance, short to power. Check and install new fuel rail pressure sensor as required.
P008A-00 Low Pressure Fuel System Pressure - Too Low - no sub type information
  • Low pressure fuel sensor circuit failure, short to ground, power, open circuit
  • Fuel Pump Driver Module (FPDM) circuit short to ground, power, open circuit
  • Low pressure fuel
  • Fuel Pump Driver Module (FPDM) failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376). Refer to the electrical circuit diagrams and check low pressure fuel sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) circuit short to ground, power, open circuit. Check and install a new low pressure fuel sensor as required. Check and install a new Fuel Pump Driver Module (FPDM) as required.
P008B-00 Low Pressure Fuel System Pressure - Too High - No sub type information
  • Low pressure fuel sensor circuit short to ground, power, open circuit
  • Fuel Pump Driver Module (FPDM) circuit short to ground, power, open circuit
  • Blockage or restriction in low pressure fuel line
  • Low pressure fuel sensor failure
  • Fuel Pump Driver Module (FPDM) failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376). Refer to the electrical circuit diagrams and check low pressure fuel sensor circuit for short to ground, power, open circuit. Check for blockage or restriction in low pressure fuel line. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) circuit short to ground, power, open circuit. Check and install a new low pressure fuel sensor as required. Check and install a new Fuel Pump Driver Module (FPDM) as required.
P00AB-23 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - signal stuck low
  • Intake air temperature sensor bank 2 circuit short to ground, open circuit
  • Intake air temperature sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312). Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short to ground, open circuit. Check and install a new intake air temperature sensor bank 2 as required.
P00AB-24 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - signal stuck high
  • Intake air temperature sensor bank 2 circuit short to power
  • Intake air temperature sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312). Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short to power. Check and install a new intake air temperature sensor bank 2 as required.
P00AB-29 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - signal invalid
  • Intake air temperature sensor bank 2 circuit short to ground, open circuit, short to power
  • Intake air temperature sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312). Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for open circuit, short to ground, short to power. Check and install a new intake air temperature sensor bank 2 as required.
P00AC-00 Intake Air Temperature Sensor 1 Circuit Low (Bank 2) - no sub type information
  • Intake air temperature sensor bank 2 sensing circuit short to ground, high resistance, disconnected
  • Intake air temperature sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312). Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short to ground, open circuit, high resistance, disconnected connector. Check and install a new intake air temperature sensor bank 2 as required.
P00AD-00 Intake Air Temperature Sensor 1 Circuit High (Bank 2) - No sub type information
  • Intake air temperature sensor bank 2 sensing circuit short ground, short to power, open circuit, high resistance
  • Intake air temperature sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312). Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short ground, short to power, open circuit, high resistance. Check for backed out or damaged connector pins. Check and install a new intake air temperature sensor bank 2 as required.
P00C6-00 Fuel Rail Pressure Too Low - Engine Cranking - no sub type information
  • No fuel at pump
  • Injector stuck open
  • Fuel pressure sensor signal stuck
  • Fuel pump failure
 Check fuel supply to both pumps (if engine runs then supply is not suspect). If engine does not run perform fuel prime routine. Use fuel pump diagnostic routine to determine if one pump has failed, if so replace pump. If a fuel injector is stuck open the exhaust will smell of fuel and fuelling adaptions may indicate rich shift. perform checks for as DTC P0191-00. Check and install a new fuel pump as required.
P0101-00 Mass or Volume Air Flow A Circuit Range/Performance - no sub type information
    NOTE: Customer likely to report hesitation.
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • MAF/IAT sensor bank 1 circuit - high resistance, intermittent short to ground, high resistance
  • MAF/IAT sensor bank 1 failure
 Check air cleaner element is free from restriction. Check for leak from air intake system, rectify as required. Ensure the engine breather system is correctly installed and in serviceable condition. Make sure throttle blade is clean of carbon. Check for blocked catalysts. Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 1 sensor circuit for intermittent short to ground, high resistance. Check and install a new MAF/IAT sensor bank 1 sensor as required.
P0102-00 Mass or Volume Air Flow A Circuit Low - no sub type information
    NOTE: Customer likely to report hesitation.
  • Mass Air Flow (MAF) sensor bank 1 circuit high resistance, open circuit
  • Mass Air Flow (MAF) sensor bank 1 failure
 Refer to the electrical circuit diagrams and check Mass Air Flow (MAF) bank 1 circuit for high resistance, open circuit. Check and install a new Mass Air Flow (MAF) bank 1 as required.
P0103-00 Mass or Volume Air Flow A Circuit High - no sub type information
    NOTE: Customer likely to report hesitation.
  • Mass Air Flow (MAF) sensor bank 1 circuit short to power, high resistance
  • Mass Air Flow (MAF) sensor bank 1 failure
 Check circuit fuse. If fuse fails, may see P0103, P010C and P250C. Refer to the electrical circuit diagrams and check Mass Air Flow (MAF) bank 1 circuit for short to power, high resistance. Check and install a new Mass Air Flow (MAF) bank 1 as required.
P010B-00 Mass or Volume Air Flow B Circuit Range/Performance - no sub type information
    NOTE: Customer likely to report hesitation.
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • MAF/IAT sensor bank 2 circuit - high resistance, intermittent short to ground, high resistance
  • MAF/IAT sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503). Check for related DTCs P0102 or P0103. Check air cleaner element is free from restriction. Check for leak from air intake system, rectify as required. Ensure the engine breather system is correctly installed and in serviceable condition. Make sure throttle blade is clean of carbon. Check for blocked catalysts. Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 2 sensor circuit for intermittent short to ground, high resistance. Check and install a new MAF/IAT sensor bank 2 sensor as required.
P010C-00 Mass or Volume Air Flow B Circuit Low - no sub type information
    NOTE: Customer likely to report hesitation.
  • Mass Air Flow (MAF) sensor bank 2 circuit high resistance, open circuit, short to ground, short to power
  • Mass Air Flow (MAF) sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503). Check Mass Air Flow (MAF) sensor circuit fuse. If fuse fails, may see DTCs P0103, P010C and P250C. Refer to the electrical circuit diagrams and check Mass Air Flow (MAF) bank 2 circuit for high resistance, open circuit, short to ground, short to power. Check and install a new Mass Air Flow (MAF) bank 2 as required.
P010D-00 Mass or Volume Air Flow B Circuit High - no sub type information
    NOTE: Customer likely to report hesitation.
  • Mass Air Flow (MAF) sensor bank 2 circuit high resistance, open circuit, short to ground, short to power
  • Mass Air Flow (MAF) sensor bank 2 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503). Check Mass Air Flow (MAF) sensor circuit fuse. If fuse fails, may see DTCs P0103, P010C and P250C. Refer to the electrical circuit diagrams and check Mass Air Flow (MAF) bank 2 circuit for high resistance, open circuit, short to ground, short to power. Check and install a new Mass Air Flow (MAF) bank 2 as required.
P010F-00 Mass or Volume Air Flow Sensor A/B Correlation - no sub type information
    NOTE: Customer likely to report hesitation.
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • MAF/IAT sensor bank 1 circuit - high resistance, intermittent short to ground, high resistance
  • MAF/IAT sensor bank 1 failure
 Check air cleaner element is free from restriction. Check for leak from air intake system, rectify as required. Ensure the engine breather system is correctly installed and in serviceable condition. Make sure throttle blade is clean of carbon. Check for blocked catalysts. Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 1 sensor circuit for intermittent short to ground, high resistance. Check and install a new MAF/IAT sensor bank 1 sensor as required.
P0111-23 Intake Air Temperature Sensor 1 Circuit Range/Performance - signal stuck low
  • Intake air temperature sensor short to ground, open circuit, high resistance
  • Intake air temperature sensor failure
 Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short to ground, open circuit, high resistance. Check and install a new intake air temperature sensor as required.
P0111-24 Intake Air Temperature Sensor 1 Circuit Range/Performance - signal stuck high
  • Intake air temperature sensor circuit short to power, open circuit
  • Intake air temperature sensor failure
 Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short to power, open circuit. Check and install a new intake air temperature sensor as required.
P0111-29 Intake Air Temperature Sensor 1 Circuit Range/Performance - signal invalid
  • Intake air temperature sensor circuit short to ground, power, open circuit
  • Intake air temperature sensor failure
 Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short to ground, power, open circuit. Check and install a new intake air temperature sensor as required.
P0112-00 Intake Air Temperature Sensor 1 Circuit Low (Bank 1) - no sub type information
  • Intake air temperature sensor circuit short to ground, short to power, open circuit, high resistance
  • Intake air temperature sensor failure
 Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short to ground, short to power, open circuit, high resistance. Check and install a new intake air temperature sensor bank 1 as required.
P0113-00 Intake Air Temperature Sensor 1 Circuit High (Bank 1) - no sub type information
  • Intake air temperature sensor circuit short to power, open circuit, high resistance
  • Intake air temperature sensor failure
 Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short to power, open circuit, high resistance. Check and install a new intake air temperature sensor bank 1 as required.
P0116-23 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - signal stuck low
  • Engine coolant temperature sensor 1 sensing circuit intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Battery reset carried out when the engine was warm/hot
 Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357). Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance. Check and install a new engine coolant temperature sensor 1 as required. Check for related DYC P2610- 87. Start the engine and switch off. Clear DTC and re-test.
P0116-24 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - signal stuck high
  • Engine coolant temperature sensor 1 sensing circuit intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Battery reset carried out when the engine was warm/hot
 Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357). Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance. Check and install a new engine coolant temperature sensor 1 as required. Check for related DYC P2610- 87. Start the engine and switch off. Clear DTC and re-test.
P0116-29 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - Signal invalid
  • Low coolant level
  • Engine coolant temperature sensor 1 sensing circuit - intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Possible airlock in cooling system
 Fill cooling system to correct level and specification. Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357). Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance. Check and install new engine coolant temperature sensor 1 as required, Bleed cooling system.
P0117-16 Engine Coolant Temperature Sensor 1 Circuit Low - circuit voltage below threshold
  • Engine coolant temperature sensor 1 circuit short to ground
  • Engine coolant temperature sensor 1 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357). Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short to ground. Check and install a new Engine coolant temperature sensor 1 as required.
P0118-17 Engine Coolant Temperature Sensor 1 Circuit High - Circuit voltage above threshold
  • Engine coolant temperature sensor 1 circuit short to power, open circuit, sensor disconnected
  • Engine coolant temperature sensor 1 failure
 Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357). Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short to power, open circuit, sensor disconnected. Check and install new engine coolant temperature sensor 1 as required.
P0121-00 Throttle/Pedal Position Sensor A Circuit Range/Performance - no sub type information
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply circuit open circuit, high resistance
  • Engine Control Module (ECM) damage through water ingress, internal fault
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) power supply circuit for open circuit, high resistance. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0122-00 Throttle/Pedal Position Sensor A Circuit Low - no sub type information
  • Throttle position sensor 1 circuit short to ground, open circuit
  • Throttle position sensor 1 failure
 Refer to the electrical circuit diagrams and check throttle position sensor 1 circuit for short to ground, open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0123-00 Throttle/Pedal Position Sensor A Circuit High - no sub type information
  • Throttle position sensor 1 circuit short to ground, short to power, open circuit
  • Throttle position sensor 1 failure
 Refer to the electrical circuit diagrams and check throttle position sensor 1 circuit for short to ground, short to power, open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0125-00 Insufficient Coolant Temp For Closed Loop Fuel Control - no sub type information
  • Coolant temperature sensor 1 circuit, open circuit, high resistance
  • Engine coolant temperature sensor 1 failure
 Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for open circuit, high resistance. Check and install a new engine coolant temperature sensor 1.
P0126-26 Insufficient Coolant Temp For Stable Operation - signal rate of change below threshold
  • Thermostat stuck open
  • Cooling fans running continuously or at a high duty
 Check for related coolant temperature coolant sensor faults. Check and install a new thermostat as required. Check cooling fans for correct operation. Repair as required.
P0128-00 Coolant Thermostat (Coolant Temp Below Thermostat Regulating Temperature) - no sub type information
  • Thermostat stuck open
  • Coolant temperature coolant sensor circuit, short to ground, short to power, open circuit
 Check for related coolant temperature coolant sensor faults. Check and install a new thermostat as required. Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short to ground, short to power, open circuit.
P0131-00 O2 Circuit Low Voltage (Bank 1, Sensor 1) - no sub type information
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short to ground
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
 Check pre-catalyst oxygen sensor odd connector is connected. Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short to ground, open circuit. Check pre-catalyst oxygen sensor odd heater circuit. Check and install a new pre-catalyst oxygen sensor odd as required.
P0132-00 O2 Circuit High Voltage (Bank 1, Sensor 1) - no sub type information
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short to power
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
 Check pre-catalyst oxygen sensor odd connector is connected. Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short to power, open circuit. Check pre-catalyst oxygen sensor odd heater circuit. Check and install a new pre-catalyst oxygen sensor odd as required.
P0133-00 O2 Circuit Slow Response (Bank 1, Sensor 1) - no sub type information
  • Exhaust leak
  • Pre-catalyst oxygen sensor odd to Engine Control Module (ECM) wiring shield high resistance
  • Fuel control system fault
  • Pre-catalyst oxygen sensor odd failure
 Check pre-catalyst oxygen sensor odd is correctly installed in exhaust manifold. Check for and rectify any exhaust leak between cylinder head and catalytic converter. Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd to Engine Control Module (ECM) wiring shield for high resistance. Check fuel control system for failure. Check and install a new pre-catalyst oxygen sensor odd as required.
P0134-00 O2 Circuit No Activity Detected (Bank 1, Sensor 1) - no sub type information
  • Pre-catalyst oxygen sensor odd circuit short to ground, short to power, open circuit
  • Pre-catalyst oxygen sensor odd failure
 Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd circuit for short to ground, short to power, open circuit. Check and install a new pre-catalyst oxygen sensor odd as required.
P0137-00 O2 Circuit Low Voltage (Bank 1, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - odd, sensing circuit short to ground, high resistance, open circuit
  • Damaged or blocked catalyst
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - odd, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to ground, high resistance, open circuit. Check for damaged or blocked catalyst. Check for air leak between catalyst and exhaust manifold. Check and install new post catalyst oxygen sensor - odd, as required.
P0138-00 O2 Circuit High Voltage (Bank 1, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - odd, sensing circuit short to power
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Catalyst blocked
  • Post catalyst oxygen sensor - odd, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to power. Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required. Check for blocked catalyst. Check and install new catalyst as required. Check and install new post catalyst oxygen sensor - odd, as required.
P0139-00 O2 Circuit Slow Response (Bank 1, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Excessive oil consumption
 Check for related DTCs. Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required. Check for excessive oil consumption. Repair as required.
P0140-00 O2 Circuit No Activity Detected (Bank 1, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - odd, sensing circuit short to ground, power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - odd, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to ground, power, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required. Check for excessive oil consumption. Check and install new post catalyst oxygen sensor - odd, as required.
P0141-00 O2 Heater Circuit (Bank 1, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - odd, sensing circuit short to ground, power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor - odd, failure
 Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 2 (0x03A2). Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to ground, power, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install new post catalyst oxygen sensor - odd, as required.
P0148-65 Fuel Delivery Error - signal has too few transitions / events
  • Injector(s) circuit, short to ground, short to power, high resistance
  • Injector(s) failure
  • Engine Control Module (ECM) internal failure
 Check for related injector DTCs. Refer to the electrical circuit diagrams and check Injector(s) circuit for, short to ground, short to power, high resistance. Check and install a new injector(s) as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0148-66 Fuel Delivery Error - signal has too many transitions / events
  • Injector(s) circuit, short to ground, short to power, high resistance
  • Injector(s) failure
  • Engine Control Module (ECM) internal failure
 Check for related injector DTCs. Refer to the electrical circuit diagrams and check Injector(s) circuit for, short to ground, short to power, high resistance. Check and install a new injector(s) as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0149-32 Fuel Timing Error - signal low time < minimum
  • Injector(s) circuit, short to ground, short to power, high resistance
  • Injector(s) failure
  • Engine Control Module (ECM) internal failure
 Check for related injector DTCs. Refer to the electrical circuit diagrams and check Injector(s) circuit for, short to ground, short to power, high resistance. Check and install a new injector(s) as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0149-35 Fuel Timing Error - signal high time > maximum
  • Injector(s) circuit, short to ground, short to power, high resistance
  • Injector(s) failure
  • Engine Control Module (ECM) internal failure
 Check for related injector DTCs. Refer to the electrical circuit diagrams and check Injector(s) circuit for, short to ground, short to power, high resistance. Check and install a new injector(s) as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0151-1A O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1) - circuit resistance below threshold
  • Pre-catalyst oxygen sensor - even circuit short to ground
  • Pre-catalyst oxygen sensor - even failure
 Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor - even circuit for short to ground. Check and install new pre catalyst oxygen sensor - even.
P0152-1B O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1) - circuit resistance above threshold
  • Pre-catalyst oxygen sensor - even circuit short to power, disconnected
  • Pre-catalyst oxygen sensor - even failure
 Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor - even circuit for short to power, disconnected. Check and install new pre catalyst oxygen sensor - even.
P0153-00 O2 Circuit Slow Response (Bank 2, Sensor 1) - no sub type information
  • Exhaust leak
  • Pre-catalyst oxygen sensor even to Engine Control Module (ECM) wiring shield high resistance
  • Pre-catalyst oxygen sensor even to Engine Control Module (ECM) signal circuit short to ground
  • Fuel control system fault
  • Pre-catalyst oxygen sensor even failure
 Check pre-catalyst oxygen sensor even is correctly installed in exhaust manifold. Check for and rectify any exhaust leak between cylinder head and catalytic converter. Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor even to Engine Control Module (ECM) wiring shield for high resistance. Refer to the electrical circuit diagrams and check Pre-catalyst oxygen sensor even to Engine Control Module (ECM) signal circuit for short to ground. Check fuel control system for failure. Check and install a new pre-catalyst oxygen sensor even as required.
P0154-00 O2 Circuit No Activity Detected (Bank 2, Sensor 1) - no sub type information
  • Exhaust leak
  • Pre-catalyst oxygen sensor even to Engine Control Module (ECM) wiring shield high resistance
  • Pre-catalyst oxygen sensor even to Engine Control Module (ECM) signal circuit short to ground, high resistance, open circuit
  • Fuel control system fault
  • Pre-catalyst oxygen sensor even failure
 Check pre-catalyst oxygen sensor even is correctly installed in exhaust manifold. Check for and rectify any exhaust leak between cylinder head and catalytic converter. Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor even to Engine Control Module (ECM) wiring shield for high resistance. Refer to the electrical circuit diagrams and check Pre-catalyst oxygen sensor even to Engine Control Module (ECM) signal circuit for short to ground, high resistance, open circuit. Check fuel control system for failure. Check and install a new pre-catalyst oxygen sensor even as required.
P0157-00 O2 Circuit Low Voltage (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - even, sensing circuit short to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short to ground, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned, install a new sensor as required. Check and install new post catalyst oxygen sensor - even, as required.
P0158-00 O2 Circuit High Voltage (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - even, sensing circuit short to power
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short to power. Check for air leak between catalyst and exhaust manifold. Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned, install a new sensor as required. Check and install new post catalyst oxygen sensor - even, as required.
P0159-00 O2 Circuit Slow Response (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Excessive oil consumption
 Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned, install a new sensor as required. Check for excessive oil consumption, repair as required.
P0160-00 O2 Circuit No Activity Detected (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - even, sensing circuit short to ground, power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short to ground, power, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned, install a new sensor as required. Check and install new post catalyst oxygen sensor - even, as required.
P0161-00 O2 Heater Circuit (Bank 2, Sensor 2) - no sub type information
  • Post catalyst oxygen sensor - even, sensing circuit short to ground, power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, sensing circuit fuse failure
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor - even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short to ground, power, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check Post catalyst oxygen sensor - even, sensing circuit fuse, replace as required. Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install new post catalyst oxygen sensor - even, as required.
P0171-00 System Too Lean (Bank 1) - no sub type information
  • Air leak upstream of MAF/IAT sensor bank 1
  • MAF/IAT sensor bank 1 circuit failure
  • MAF/IAT sensor bank 1 failure
  • Pre-catalyst oxygen sensor odd circuit failure
  • Pre-catalyst oxygen sensor odd failure
  • Post-catalyst oxygen sensor odd circuit failure
  • Post-catalyst oxygen sensor odd failure
 Check for leak from air intake system. Check for additional MAF/IAT sensor bank 1 related DTCs and refer to relevant DTC Index. Check for additional Pre-catalyst oxygen sensor odd related DTCs and refer to relevant DTC Index. Check for additional Post-catalyst oxygen sensor odd related DTCs and refer to relevant DTC Index.
P0172-00 System Too Rich (Bank 1) - no sub type information
  • Restricted air cleaner
  • Leaking fuel injector(s)
  • MAF/IAT sensor bank 1 failure
  • Pre-catalyst oxygen sensor odd circuit failure
  • Pre-catalyst oxygen sensor odd failure
  • Post-catalyst oxygen sensor odd circuit failure
  • Post-catalyst oxygen sensor odd failure
 Check air cleaner element is free from restriction. Check for leaking injectors, install new injector(s) as required. Check for additional MAF/IAT sensor bank 1 related DTCs and refer to relevant DTC Index. Check for additional Pre-catalyst oxygen sensor odd related DTCs and refer to relevant DTC Index. Check for additional Post-catalyst oxygen sensor odd related DTCs and refer to relevant DTC Index.
P0174-00 System Too Lean (Bank 2) - no sub type information
  • Air leak upstream of MAF/IAT sensor bank 2
  • MAF/IAT sensor bank 2 circuit failure
  • MAF/IAT sensor bank 2 failure
  • Pre-catalyst oxygen sensor even circuit failure
  • Pre-catalyst oxygen sensor even failure
  • Post-catalyst oxygen sensor even circuit failure
  • Post-catalyst oxygen sensor even failure
 Check for leak from air intake system. Check for additional MAF/IAT sensor bank 2 related DTCs and refer to relevant DTC Index. Check for additional Pre-catalyst oxygen sensor even related DTCs and refer to relevant DTC Index. Check for additional Post-catalyst oxygen sensor even related DTCs and refer to relevant DTC Index.
P0175-00 System Too Rich (Bank 2) - no sub type information
  • Restricted air cleaner
  • Leaking fuel injector(s)
  • MAF/IAT sensor bank 2 circuit failure
  • MAF/IAT sensor bank 2 failure
  • Pre-catalyst oxygen sensor even circuit failure
  • Pre-catalyst oxygen sensor even failure
  • Post-catalyst oxygen sensor even circuit failure
  • Post-catalyst oxygen sensor even failure
 Check air cleaner element is free from restriction. Check for leaking injectors, install new injector(s) as required. Check for additional MAF/IAT sensor bank 2 related DTCs and refer to relevant DTC Index. Check for additional Pre-catalyst oxygen sensor even related DTCs and refer to relevant DTC Index. Check for additional Post-catalyst oxygen sensor even related DTCs and refer to relevant DTC Index.
P018B-29 Fuel Pressure Sensor B Circuit Range/Performance - signal invalid
  • Fuel Filter or fuel system restriction
  • Fuel system leak
  • Fuel pump pressure sensor circuit short to ground, short to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376). Check for related fuel pump DTCs. Check the fuel system for restrictions or blockages. Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short to power, open circuit, high resistance. Check and install a new fuel pump pressure sensor as required.
P018C-00 Fuel Pressure Sensor B Circuit Low - no sub type information
  • Fuel pump pressure sensor circuit short to ground, short to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376). Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short to power, open circuit, high resistance. Check and install a new fuel pump pressure sensor as required.
P018D-00 Fuel Pressure Sensor B Circuit High - no sub type information
  • Fuel pump pressure sensor circuit short to ground, short to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376). Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short to power, open circuit, high resistance. Check and install a new fuel pump pressure sensor as required.
P0191-00 Fuel Rail Pressure Sensor A Circuit Range/Performance - no sub type information
  • Fuel rail pressure sensor short to ground, short to power, open circuit, high resistance
  • Fuel Rail Pressure Sensor A failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377). Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short to power, short to ground, high resistance, open circuit, terminal damage or corrosion. Check and install a new Fuel Rail Pressure Sensor A as required.
P0192-00 Fuel Rail Pressure Sensor A Circuit Low - no sub type information
  • Fuel rail pressure sensor short to ground, short to power, open circuit, high resistance
  • Fuel Rail Pressure Sensor A failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377). Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short to power, short to ground, high resistance, open circuit, terminal damage or corrosion. Check and install a new Fuel Rail Pressure Sensor A as required.
P0193-00 Fuel Rail Pressure Sensor A Circuit High - no sub type information
  • Fuel rail pressure sensor short to ground, short to power, open circuit, high resistance
  • Fuel Rail Pressure Sensor A failure
 Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377). Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short to power, short to ground, high resistance, open circuit, terminal damage or corrosion. Check and install a new Fuel Rail Pressure Sensor A as required.
P0196-23 Engine Oil Temperature Sensor Range/Performance - signal stuck low
  • Oil temperature - level sensor circuit short to ground, high resistance
  • Oil temperature - level sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3). Refer to the electrical circuit diagrams and check oil temperature - level sensor circuit for short to ground, intermittent high resistance. Check and install new oil temperature - level sensor as required.
P0196-24 Engine Oil Temperature Sensor Range/Performance - signal stuck high
  • Oil temperature - level sensor circuit short to power
  • Oil temperature - level sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3). Refer to the electrical circuit diagrams and check oil temperature - level sensor circuit for intermittent short to power. Check and install new oil temperature - level sensor as required.
P0200-04 Injector Circuit - System Internal Failures
  • Engine Control Module (ECM) injector circuit power failure
  • Engine Control Module (ECM) fault
 Check Engine Control Module (ECM) injector power circuit for open circuit. Check for misfire DTCs, if present suspect the Engine Control Module (ECM). Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0200-49 Injector Circuit - internal electronic failure
  • Engine Control Module (ECM) fault
 Check for misfire DTCs, if present suspect the Engine Control Module (ECM). Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0200-4B Injector Circuit - over temperature
  • Engine Control Module (ECM) fault
 If combined with misfire codes for one or both injector sets, then no service rectification is proposed.
P0201-13 Cylinder 1 Injector Circuit / Open - circuit open
  • Fuel injector no. 1 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for open circuit, disconnected injector, high resistance.
P0202-13 Cylinder 2 Injector Circuit / Open - circuit open
  • Fuel injector no. 2 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for open circuit, disconnected injector, high resistance.
P0203-13 Cylinder 3 Injector Circuit / Open - circuit open
  • Fuel injector no. 3 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for open circuit, disconnected injector, high resistance.
P0204-13 Cylinder 4 Injector Circuit / Open - circuit open
  • Fuel injector no. 4 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for open circuit, disconnected injector, high resistance.
P0205-13 Cylinder 5 Injector Circuit / Open - circuit open
  • Fuel injector no. 5 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for open circuit, disconnected injector, high resistance.
P0206-13 Cylinder 6 Injector Circuit / Open - circuit open
  • Fuel injector no. 6 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for open circuit, disconnected injector, high resistance.
P0207-13 Cylinder 7 Injector Circuit / Open - circuit open
  • Fuel injector no. 7 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for open circuit, disconnected injector, high resistance.
P0208-13 Cylinder 8 Injector Circuit / Open - circuit open
  • Fuel injector no. 8 circuit open circuit
  • Injector disconnected
  • Injector high resistance
 Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for open circuit, disconnected injector, high resistance.
P0222-00 Throttle/Pedal Position Sensor/Switch B Circuit High - no sub type information
  • Throttle/pedal position sensor/switch B circuit open circuit, short to ground
  • Throttle/pedal position sensor/switch B failure
 Refer to the electrical circuit diagrams and check throttle/pedal position sensor/switch B circuit for open circuit, short to ground. Check and install a new throttle/pedal position sensor/switch B as required.
P0223-00 Throttle/Pedal Position Sensor/Switch B Circuit High - no sub type information
  • Throttle/pedal position sensor/switch B circuit open circuit, short to power
  • Throttle/pedal position sensor/switch B failure
 Refer to the electrical circuit diagrams and check throttle/pedal position sensor/switch B circuit for open circuit, short to power. Check and install a new throttle/pedal position sensor/switch B as required.
P0231-23 Fuel Pump Secondary Circuit Low - signal stuck low
  • Fuel Pump Driver Module (FPDM) signal circuit short to ground, open circuit
  • Fuel Pump Driver Module (FPDM) is not energized with the ignition on
  • Fuel Pump Driver Module (FPDM) failure
 Check for related DTCs P0232-24. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) signal circuit for short to ground, open circuit. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) is energized with the ignition on. Repair as required. Check and install a new Fuel Pump Driver Module (FPDM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0232-24 Fuel Pump Secondary Circuit Low - Signal stuck high
  • Fuel Pump Driver Module (FPDM) signal circuit short to ground, open circuit
  • Fuel Pump Driver Module (FPDM) is not energized with the ignition on
  • Fuel Pump Driver Module (FPDM) failure
 Check for related DTCs P0231-23. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) signal circuit for short to ground, open circuit. Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) is energized with the ignition on. Repair as required. Check and install a new Fuel Pump Driver Module (FPDM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0251-13 Injection Pump Fuel Metering Control A - circuit open
  • Fuel rail pressure sensor circuit, open circuit
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for open circuit.
P0253-11 Injection Pump Fuel Metering Control A Low - circuit short to ground
  • Fuel rail pressure sensor circuit, short to ground
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to ground.
P0254-12 Injection Pump Fuel Metering Control A High - circuit short to battery
  • Fuel rail pressure sensor circuit, short to power
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to power.
P0256-13 Injection Pump Fuel Metering Control B - circuit open
  • Fuel rail pressure sensor circuit, open circuit
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for open circuit.
P0258-11 Injection Pump Fuel Metering Control B Low - circuit short to ground
  • Fuel rail pressure sensor circuit, short to ground
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to ground.
P0259-12 Injection Pump Fuel Metering Control B High - circuit short to battery
  • Fuel rail pressure sensor circuit, short to power
 Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to power.
P025C-14 Fuel Pump Module Control Circuit Low - circuit short to ground or open
  • Fuel Pump Driver Module (FPDM) control circuit, short to ground, open circuit
 Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) circuit short to ground, open circuit.
P025D-12 Fuel Pump Module Control Circuit High - circuit short to battery
  • Fuel Pump Driver Module (FPDM) control circuit, short to power
 Refer to the electrical circuit diagrams and check Fuel Pump Driver Module (FPDM) circuit short to power.
P0261-11 Cylinder 1 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 1 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short to ground.
P0261-12 Cylinder 1 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 1 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short to power.
P0262-01 Cylinder 1 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 1 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short to ground, short to power.
P0262-12 Cylinder 1 Injector Circuit High - circuit short to battery
  • Fuel injector no. 1 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short to power.
P0264-11 Cylinder 2 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 2 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short to ground.
P0264-12 Cylinder 2 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 2 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short to power.
P0265-01 Cylinder 2 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 2 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short to ground, short to power.
P0265-12 Cylinder 2 Injector Circuit High - circuit short to battery
  • Fuel injector no. 2 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short to power.
P0267-11 Cylinder 3 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 3 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short to ground.
P0267-12 Cylinder 3 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 3 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short to power.
P0268-01 Cylinder 3 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 3 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short to ground, short to power.
P0268-12 Cylinder 3 Injector Circuit High - circuit short to battery
  • Fuel injector no. 3 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short to power.
P0270-11 Cylinder 4 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 4 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short to ground.
P0270-12 Cylinder 4 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 4 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short to power.
P0271-01 Cylinder 4 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 4 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short to ground, short to power.
P0271-12 Cylinder 4 Injector Circuit High - circuit short to battery
  • Fuel injector no. 4 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short to power.
P0273-11 Cylinder 5 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 5 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short to ground.
P0273-12 Cylinder 5 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 5 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short to power.
P0274-01 Cylinder 5 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 5 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short to ground, short to power.
P0274-12 Cylinder 5 Injector Circuit High - circuit short to battery
  • Fuel injector no. 5 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short to power.
P0276-11 Cylinder 6 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 6 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short to ground.
P0276-12 Cylinder 6 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 6 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short to power.
P0277-01 Cylinder 6 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 6 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short to ground, short to power.
P0277-12 Cylinder 6 Injector Circuit High - circuit short to battery
  • Fuel injector no. 6 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short to power.
P0279-11 Cylinder 7 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 7 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short to ground.
P0279-12 Cylinder 7 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 7 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short to power.
P0280-01 Cylinder 7 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 7 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short to ground, short to power.
P0280-12 Cylinder 7 Injector Circuit High - circuit short to battery
  • Fuel injector no. 7 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short to power.
P0282-11 Cylinder 8 Injector Circuit Low - circuit short to ground
  • Fuel injector no. 8 circuit short to ground
 Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short to ground.
P0282-12 Cylinder 8 Injector Circuit Low - circuit short to battery
  • Fuel injector no. 8 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short to power.
P0283-01 Cylinder 8 Injector Circuit High - General Electrical Failure
  • Fuel injector no. 8 circuit short to ground, short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short to ground, short to power.
P0283-12 Cylinder 8 Injector Circuit High - circuit short to battery
  • Fuel injector no. 8 circuit short to power
 Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short to power.
P02EE-01 Cylinder 1 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 1 injector low circuit short to power
  • Cylinder 1 injector low circuit shorted to high circuit
  • Cylinder 1 injector failure
 Refer to the electrical circuit diagrams and check cylinder 1 injector circuit for short to power, shorted together. Check and install a new cylinder 1 injector as required.
P02EE-1C Cylinder 1 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02EF-01 Cylinder 2 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 2 injector low circuit short to power
  • Cylinder 2 injector low circuit shorted to high circuit
  • Cylinder 2 injector failure
 Refer to the electrical circuit diagrams and check cylinder 2 injector circuit for short to power, shorted together. Check and install a new cylinder 2 injector as required.
P02EF-1C Cylinder 2 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F0-01 Cylinder 3 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 3 injector low circuit short to power
  • Cylinder 3 injector low circuit shorted to high circuit
  • Cylinder 3 injector failure
 Refer to the electrical circuit diagrams and check cylinder 3 injector circuit for short to power, shorted together. Check and install a new cylinder 3 injector as required.
P02F0-1C Cylinder 3 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F1-01 Cylinder 4 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 4 injector low circuit short to power
  • Cylinder 4 injector low circuit shorted to high circuit
  • Cylinder 4 injector failure
 Refer to the electrical circuit diagrams and check cylinder 4 injector circuit for short to power, shorted together. Check and install a new cylinder 4 injector as required.
P02F1-1C Cylinder 4 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F2-01 Cylinder 5 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 5 injector low circuit short to power
  • Cylinder 5 injector low circuit shorted to high circuit
  • Cylinder 5 injector failure
 Refer to the electrical circuit diagrams and check cylinder 5 injector circuit for short to power, shorted together. Check and install a new cylinder 5 injector as required.
P02F2-1C Cylinder 5 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F3-01 Cylinder 6 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 6 injector low circuit short to power
  • Cylinder 6 injector low circuit shorted to high circuit
  • Cylinder 6 injector failure
 Refer to the electrical circuit diagrams and check cylinder 6 injector circuit for short to power, shorted together. Check and install a new cylinder 6 injector as required.
P02F3-1C Cylinder 6 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F4-01 Cylinder 7 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 7 injector low circuit short to power
  • Cylinder 7 injector low circuit shorted to high circuit
  • Cylinder 7 injector failure
 Refer to the electrical circuit diagrams and check cylinder 7 injector circuit for short to power, shorted together. Check and install a new cylinder 7 injector as required.
P02F4-1C Cylinder 7 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P02F5-01 Cylinder 8 Injector Circuit Range/Performance - General Electrical Failure
  • Cylinder 8 injector low circuit short to power
  • Cylinder 8 injector low circuit shorted to high circuit
  • Cylinder 8 injector failure
 Refer to the electrical circuit diagrams and check cylinder 8 injector circuit for short to power, shorted together. Check and install a new cylinder 8 injector as required.
P02F5-1C Cylinder 8 Injector Circuit Range/Performance - circuit voltage out of range
  • Engine Control Module (ECM) internal fault
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index.
P0300-00 Random Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0301-00 Cylinder 1 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0302-00 Cylinder 2 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0303-00 Cylinder 3 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0304-00 Cylinder 4 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0305-00 Cylinder 5 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0306-00 Cylinder 6 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0307-00 Cylinder 7 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0308-00 Cylinder 8 Misfire Detected - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0313-00 Misfire Detected With Low Fuel - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0316-00 Misfire Detected On Startup (First 1000 Revolutions) - no sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Injector(s) circuit short to ground, short to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
 Check Engine Control Module (ECM) for related misfire DTCs and refer to this DTC Index. Check the fuel system for blockages, repair as required. Check the catalyst/exhaust system for blockage, repair as required. Check and install a new spark plug(s) as required. Refer to the electrical circuit diagrams and check injector(s) circuit for short to ground, power, open circuit. Check and install a new injector(s) as required. Check for air leaks within the intake system. Check and install a new camshaft position sensor as required.
P0327-00 Knock Sensor 1 Circuit Low (Bank1) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 front circuit short to ground, open circuit
  • Knock sensor bank 1 front failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 1 front circuit for short to ground, open circuit. Check and install a new knock sensor bank 1 front as required.
P0328-00 Knock Sensor 1 Circuit High (Bank 1) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 front circuit high resistance, short to power
  • Knock sensor bank 1 front failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 1 front circuit for short to power, high resistance. Check and install a new knock sensor bank 1 front as required.
P032C-00 Knock Sensor 3 Circuit Low (Bank1) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 front circuit short to ground
  • Knock sensor bank 2 front failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 2 front circuit for short to ground. Check and install a new knock sensor bank 2 front as required.
P032D-00 Knock Sensor 3 Circuit High (Bank1) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 front circuit high resistance, short to power
  • Knock sensor bank 2 front failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 2 front circuit for short to power, high resistance. Check and install a new knock sensor bank 2 front as required.
P0332-00 Knock Sensor 2 Circuit Low (Bank2) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 rear circuit short to ground, open circuit
  • Knock sensor bank 1 rear failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 1 rear circuit for short to ground, open circuit. Check and install a new knock sensor bank 1 rear as required.
P0333-00 Knock Sensor 2 Circuit High (Bank 2) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 rear circuit short to power
  • Knock sensor bank 1 rear failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 1 rear circuit for short to power. Check and install a new knock sensor bank 1 rear as required.
P0335-02 Crankshaft Position Sensor A Circuit - General signal failure
  • Crankshaft position sensor circuit short to ground, short to power, high resistance, disconnected
  • Crankshaft position sensor failure
 Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short to ground, short to power, high resistance, disconnected. Check and install new crankshaft position as required.
P0335-31 Crankshaft Position Sensor A Circuit - no signal
  • Crankshaft position sensor circuit - short to ground, short to power, high resistance, disconnected
  • Crankshaft position sensor failure
 Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short to ground, short to power, high resistance, disconnected. Check and install new crankshaft position as required.
P0336-00 Crankshaft Position Sensor A Circuit Range/Performance - no sub type information
  • Crankshaft position sensor circuit short to ground, short to power, high resistance, disconnected
  • Crankshaft position sensor gap incorrect, foreign matter on sensor face, damaged teeth on rotor
  • Crankshaft position sensor failure
 Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short to ground, short to power, high resistance, disconnected. Check crankshaft position sensor for damage and check air gap (check at 90° intervals, should be no greater than 4.5mm). Check and install new crankshaft position as required.
P033C-00 Knock Sensor 4 Circuit Low (Bank 2) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 rear circuit short to ground
  • Knock sensor bank 2 rear failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 2 rear circuit for short to ground. Check and install a new knock sensor bank 2 rear as required.
P033D-00 Knock Sensor 4 Circuit High (Bank 2) - no sub type information
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 rear circuit high resistance, short to power
  • Knock sensor bank 2 rear failure
 Ensure a good electrical contact with the cylinder block. Refer to the electrical circuit diagrams and check knock sensor bank 2 rear circuit for short to power, high resistance. Check and install a new knock sensor bank 2 rear as required.
P0340-02 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) - General signal failure
  • Camshaft position sensor bank 1 inlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 1 inlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 1 inlet as required.
P0340-31 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) - no signal
  • Camshaft position sensor bank 1 inlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 1 inlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 1 inlet as required.
P0341-00 Camshaft Position Sensor A Circuit Range/Performance (Bank 1 or single sensor) - no sub type information
  • Camshaft position sensor bank 1 inlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 1 inlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 1 inlet as required.
P0345-02 Camshaft Position Sensor A Circuit (Bank 2) - General signal failure
  • Camshaft position sensor bank 2 inlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 2 inlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 2 inlet as required.
P0345-31 Camshaft Position Sensor A Circuit (Bank 2) - no signal
  • Camshaft position sensor bank 2 inlet sensor circuit - short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 2 inlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 2 inlet as required.
P0346-00 Camshaft Position Sensor A Circuit Range/Performance (Bank 2) - no sub type information
  • Camshaft position sensor bank 2 inlet sensor circuit - short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, target rotor run-out
  • Camshaft position sensor bank 2 inlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 2 inlet sensor for correct installation and damage. Check target rotor for run out, repair as required. Check and install a new camshaft position sensor bank 2 inlet as required.
P0351-13 Ignition Coil A Primary/Secondary Circuit - circuit open
  • Ignition coil 1 open circuit
  • Ignition coil 1 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 1 circuit for open circuit, disconnected ignition coil, high resistance.
P0352-13 Ignition Coil B Primary/Secondary Circuit - circuit open
  • Ignition coil 2 open circuit
  • Ignition coil 2 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 2 circuit for open circuit, disconnected ignition coil, high resistance.
P0353-13 Ignition Coil C Primary/Secondary Circuit - circuit open
  • Ignition coil 3 open circuit
  • Ignition coil 3 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 3 circuit for open circuit, disconnected ignition coil, high resistance.
P0354-13 Ignition Coil D Primary/Secondary Circuit - circuit open
  • Ignition coil 4 open circuit
  • Ignition coil 4 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 4 circuit for open circuit, disconnected ignition coil, high resistance.
P0355-13 Ignition Coil E Primary/Secondary Circuit - circuit open
  • Ignition coil 5 open circuit
  • Ignition coil 5 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 5 circuit for open circuit, disconnected ignition coil, high resistance.
P0356-13 Ignition Coil F Primary/Secondary Circuit - Circuit Open
  • Ignition coil 6 open circuit
  • Ignition coil 6 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 6 circuit for open circuit, disconnected ignition coil, high resistance.
P0357-13 Ignition Coil G Primary/Secondary Circuit - circuit open
  • Ignition coil 7 open circuit
  • Ignition coil 7 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 7 circuit for open circuit, disconnected ignition coil, high resistance.
P0358-13 Ignition Coil H Primary/Secondary Circuit - circuit open
  • Ignition coil 8 open circuit
  • Ignition coil 8 disconnected
  • Ignition coil high resistance
 Refer to the electrical circuit diagrams and check ignition coil 8 circuit for open circuit, disconnected ignition coil, high resistance.
P0365-02 Camshaft Position Sensor B Circuit (Bank 1) - General signal failure
  • Camshaft position sensor bank 1 outlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 1 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 outlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 outlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 1 outlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 1 outlet as required.
P0366-00 Camshaft Position Sensor B Circuit Range/Performance (Bank 1) - No sub type information
  • Camshaft position sensor bank 1 outlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 1 outlet sensor gap incorrect, foreign matter on sensor face, target rotor run-out
  • Camshaft position sensor bank 1 outlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 outlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 1 outlet sensor for correct installation and damage. Check target run-out, repair as required. Check and install a new camshaft position sensor bank 1 outlet as required.
P0390-02 Camshaft Position Sensor B Circuit (Bank 2) - performance or incorrect operation
  • Camshaft position sensor bank 2 outlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 2 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 outlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 outlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 2 outlet sensor for correct installation and damage. Check and install a new camshaft position sensor bank 2 outlet as required.
P0391-00 Camshaft Position Sensor B Circuit Range/Performance (Bank 2) - no sub type information
  • Camshaft position sensor bank 2 outlet sensor circuit short to ground, short to power, high resistance, disconnected
  • Camshaft position sensor bank 2 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor, rotor run-out
  • Camshaft position sensor bank 2 outlet sensor failure
 Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 outlet sensor circuit for short to ground, short to power, high resistance, disconnected. Check camshaft position sensor bank 2 outlet sensor for correct installation and damage. Check target rotor, repair as required. Check and install a new camshaft position sensor bank 2 outlet as required.
P0420-00 Catalyst System Efficiency Below Threshold (Bank 1) - no sub type information
  • Catalytic converter failure due to overheating damage caused by misfire and/or lean combustion
  • Catalytic converter failure due to poisoning caused by excessive oil consumption and/or contaminated fuel
 Check for misfire/lean combustion DTCs and refer to DTC Index in this section. Check the oil and fuel condition/level. Check the catalytic converter for damage. Check and install a new catalytic converter bank 1 as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0430-00 Catalyst System Efficiency Below Threshold (Bank 2) - no sub type information
  • Catalytic converter failure due to overheating damage caused by misfire and/or lean combustion
  • Catalytic converter failure due to poisoning caused by excessive oil consumption and/or contaminated fuel
 Check for misfire/lean combustion DTCs and refer to DTC Index in this section. Check the oil and fuel condition/level. Check the catalytic converter for damage. Check and install a new catalytic converter bank 2 as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0441-00 Evaporative Emission System Incorrect Purge Flow - no sub type information
  • Evaporative Emission (EVAP) system hoses, pipes or connection failure
  • Purge control valve circuit short to ground, short to power, open circuit, high resistance
  • Purge control valve failure
 Check all Evaporative Emission (EVAP) system hoses, pipes and connection are serviceable, repair/replace as required. Refer to the electrical circuit diagrams and check purge control valve circuit for short to ground, power, open circuit. Check and install a new purge control valve as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0442-00 Evaporative Emission System Leak Detected (small leak)- no sub type information
  • Fuel filler cap not sealing/missing
  • Diagnostic Module Tank Leakage (DMTL) connector not sealed
  • Purge valve dirty
  • Evaporative emission system leak
  • Fuel tank, filler neck leak
  • Diagnostic Module Tank Leakage (DMTL) module failure
 Check fuel tank filler cap for sealing/missing. Check and install a new fuel tank filler cap as required. Check EVAP system for leak using appropriate smoke/leak tester. Carry out a purge valve self test to clean the purge valve. Check fuel tank and filler neck for leakage, replace as required. Check and install a new Diagnostic Module Tank Leakage (DMTL) module as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0444-13 Evaporative Emission System Purge Control Valve Circuit Open - circuit open
  • Purge control valve open circuit, high resistance, disconnected
 Refer to the electrical circuit diagrams and check purge control valve circuit for open circuit, disconnected purge valve, high resistance.
P0447-00 Evaporative Emission System Vent Control Circuit Open - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) module circuit open circuit
  • Diagnostic Module Tank Leakage (DMTL) module circuit fuse blown / not secure in holder
  • Diagnostic Module Tank Leakage (DMTL) module failure
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) module circuit for open circuit. Check Diagnostic Module Tank Leakage (DMTL) module fuse and replace as required. Check and install a new Diagnostic Module Tank Leakage (DMTL) module as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0448-00 Evaporative Emission System Vent Control Circuit Shorted - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) module circuit, short to ground, short to power, open circuit
  • Diagnostic Module Tank Leakage (DMTL) module failure
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) module circuit for short to ground, short to power, open circuit. Check and install a new Diagnostic Module Tank Leakage (DMTL) module as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0456-00 Evaporative Emission System Leak Detected (very small leak) - no sub type information
  • Fuel filler cap not sealing/missing
  • Diagnostic Module Tank Leakage (DMTL) connector not sealed
  • Purge valve dirty
  • Evaporative emission system leak
  • Fuel tank, filler neck leak
  • Diagnostic Module Tank Leakage (DMTL) module failure
 Check fuel tank filler cap for sealing/missing. Check and install a new fuel tank filler cap as required. Check EVAP system for leak using appropriate smoke/leak tester. Carry out a purge valve self test to clean the purge valve. Check fuel tank and filler neck for leakage, replace as required. Check and install a new Diagnostic Module Tank Leakage (DMTL) module as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0458-11 Evaporative Emission System Purge Control Valve Circuit High - circuit short to ground
  • Evaporative emission system purge control valve circuit short to ground
 Refer to the electrical circuit diagrams and check evaporative emission system purge control valve circuit for short to ground.
P0459-12 Evaporative Emission System Purge Control Valve Circuit High - circuit short to battery
  • Evaporative emission system purge control valve circuit short to power
 Refer to the electrical circuit diagrams and check evaporative emission system purge control valve circuit for short to power.
P0461-29 Fuel Level Sensor A Circuit Range/Performance - signal invalid
  • Fuel level sensor circuit open circuit, short to ground, short to power
  • Fuel level sensor stuck
  • Fuel level sensor failure
 Refer to the electrical circuit diagrams and check fuel level sensor circuit for short to ground, short to power, open circuit. Check for stuck level sensor. Check and install a new fuel level sensor as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0461-2F Fuel Level Sensor A Circuit Range/Performance - signal erratic
  • Fuel level sensor circuit short to ground, short to power, open circuit
  • Fuel level sensor track damaged
  • Fuel level sensor failure
 Refer to the electrical circuit diagrams and check fuel level sensor circuit for short to ground, short to power, open circuit. Check level sensor track for damage. Check and install a new fuel level sensor as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0481-04 Fan 2 Control Circuit - system internal failures
  • Damaged cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-09 Fan 2 Control Circuit - component failures
  • Damaged cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-11 Fan 2 Control Circuit - short to ground
  • Cooling fan control unit circuit short to ground
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Refer to the electrical circuit diagrams and check cooling fan control unit circuit for short to ground.
P0481-12 Fan 2 Control Circuit - short to battery
  • Cooling fan control unit circuit short to power
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Refer to the electrical circuit diagrams and check cooling fan control unit circuit for short to power.
P0481-13 Fan 2 Control Circuit - circuit open
  • Cooling fan control unit circuit open circuit
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Refer to the electrical circuit diagrams and check cooling fan control unit circuit for open circuit.
P0481-16 Fan 2 Control Circuit - circuit voltage below threshold
  • Charging system fault
  • Discharged battery
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Refer to the electrical circuit diagrams and check charging circuit for open circuit, short to ground. Check and install a new alternator as required. Check and install a new battery as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-17 Fan 2 Control Circuit - circuit voltage above threshold
  • Charging system fault
  • Discharged battery
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Refer to the electrical circuit diagrams and check charging circuit for open circuit, short to ground. Check and install a new alternator as required. Check and install a new battery as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-38 Fan 2 Control Circuit - signal frequency incorrect
  • Damaged cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-4B Fan 2 Control Circuit - Over temperature
  • Damaged cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-93 Fan 2 Control Circuit - no operation
  • Damaged cooling fan control unit
  • Blocked cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check for block or obstruction to fan rotor. Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-96 Fan 2 Control Circuit - component internal failure
  • Damaged cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0481-97 Fan 2 Control Circuit - component or system operation obstructed or blocked
  • Damaged cooling fan control unit
  • Blocked cooling fan control unit
  • Cooling fan control unit failure
 Using the manufacturer approved diagnostic system check datalogger signal, Electric Fan PWM Control - Commanded Duty Cycle (0x03F9). Check for block or obstruction to fan rotor. Check and install a new cooling fan control unit as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0500-81 Vehicle Speed Sensor A - invalid serial data received
  • Wheel speed sensor fault
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
P0500-82 Vehicle Speed Sensor A - alive / sequence counter incorrect / not updated
  • Anti-lock Braking System (ABS) module not on bus
 Check Anti-lock Braking System (ABS) module and Engine Control Module (ECM) for related DTCs and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check Anti-lock Braking System (ABS) module circuit for short to ground, power, open circuit.
P0500-83 Vehicle Speed Sensor A - value of signal protection calculation incorrect
  • Incorrect level of Anti-lock Braking System (ABS) module software
  • Incorrect level of Engine Control Module (ECM) software
 Clear DTC and re-test. Re-configure the Anti-lock Braking System (ABS) module using the manufacturer approved diagnostic system. Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system.
P0500-85 Vehicle Speed Sensor A - signal above allowable range
  • Anti-lock Braking System (ABS) module has reported a speed above 300 km/h
 Check Anti-lock Braking System (ABS) module for related DTCs and refer to relevant DTC Index.
P0501-62 Vehicle Speed Sensor A Range/Performance - signal compare failure
  • Vehicle speed from the Anti-lock Braking System (ABS) module does not match the calculated vehicle speed from the Engine Control Module (ECM)
 Check Engine Control Module (ECM) for related vehicle speed DTCs and refer to relevant DTC Index. Check Anti-lock Braking System (ABS) module and Transmission Control Module (TCM) for related DTCs and refer to relevant DTC Index. Check the vehicle tyre sizes are correct.
P0504-00 Brake Switch A / B Correlation - no sub type information
  • No brake pressure signal available from Anti-Lock (ABS) braking module
  • Brake switch 1 and Brake switch 2 sense circuit short to ground, short to power, open circuit
  • Brake switch 1 failure
 Check Anti-Lock braking module for related DTCs and refer to relevant DTC Index. Check for brake fluid leaks. Refer to the electrical circuit diagrams and check Anti-lock Braking System (ABS) module circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check brake switch circuit for short to ground, power, open circuit. Check and install a new brake switch 1 as required.
P0504-64 Brake Switch A / B Correlation - signal plausibility failure
  • Brake fluid leak
  • Brake switch 1 sense circuit short to power
  • Brake switch 1 failure
 Check for brake fluid leaks. Refer to the electrical circuit diagrams and check brake switch 1 circuit for short to power. Check and install a new brake switch 1 as required.
P0506-00 Idle Air Control System RPM Lower Than Expected - no sub type information
  • Air intake restriction
  • Front end accessory drive (FEAD) overload (defective/seized component)
 Ensure the air intake system is free from restriction. Check the FEAD belt and components for failure, repair as required.
P0506-24 Idle Air Control System RPM Lower Than Expected - signal stuck high
  • Air intake restriction
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
  • Front end accessory drive (FEAD) overload (defective/seized component)
 Ensure the air intake system is free from restriction. Check for air leak between MAF/IAT sensor and throttle. Check for air leak between throttle and inlet manifold. Check for engine breather system leak. Check the FEAD belt and components for failure.
P0507-00 Idle Air Control System RPM Higher Than Expected - no sub type information
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
 Check for air leak between MAF/IAT sensor and throttle. Check for air leak between throttle and inlet manifold. Check for engine breather system leak.
P0507-23 Idle Air Control System RPM Higher Than Expected - signal stuck low
  • Air intake restriction
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
 Ensure the air intake system is free from restriction. Check for air leak between MAF/IAT sensor and throttle. Check for air leak between throttle and inlet manifold. Check for engine breather system leak.
P050B-23 Cold Start Ignition Timing Performance - signal stuck low
  • Ignition coil(s)faulty
  • Ignition coils circuit noise
  • Engine Control Module (ECM) faulty
 Refer to the electrical circuit diagrams and check ignition coil circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) to ignition coil circuit for short to power. Check and install a new coil(s) as required. Refer to the electrical circuit diagrams and check ignition coils circuit for corrosion, high resistance. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P050B-24 Cold Start Ignition Timing Performance - signal stuck high
  • Ignition coil(s)faulty
  • Ignition coils circuit noise
  • Engine Control Module (ECM) faulty
 Refer to the electrical circuit diagrams and check ignition coil circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) to ignition coil circuit for short to power. Check and install a new coil(s) as required. Refer to the electrical circuit diagrams and check ignition coils circuit for corrosion, high resistance. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P050E-00 Cold Start Engine Exhaust Temperature Too Low - no sub type information
  • Incorrect coolant temperature sensor installed
  • Coolant temperature sensor circuit short to ground, open circuit
  • Coolant temperature sensor failure
 Check the correct coolant temperature sensor is installed. Refer to the electrical circuit diagrams and check coolant temperature sensor circuit for short to ground, open circuit. Check and install a new coolant temperature sensor as required.
P0512-12 Starter Request Circuit - circuit short to battery
  • Crank request circuit between Engine Control Module (ECM) and Central Junction Box (CJB) short to power
 Refer to the electrical circuit diagrams and check crank request circuit between Engine Control Module (ECM) and Central Junction Box (CJB) for short to power.
P0512-14 Starter Request Circuit - circuit short to ground or open
  • Crank request circuit between Engine Control Module (ECM) and Central Junction Box (CJB) short to ground, open circuit
 Refer to the electrical circuit diagrams and check crank request circuit between Engine Control Module (ECM) and Central Junction Box (CJB) for short to ground, open circuit.
P0513-00 Incorrect Immobilizer Key - no sub type information
  • Security key invalid
  • Controller Area Network (CAN) data corruption
  • Low battery voltage
 Check for CAN network interference/Engine Control Module (ECM) related error. Carry out the CAN network integrity test using the manufacturer approved diagnostic system. Check the vehicle charging system for faults, repair as required.
P052A-00 Cold Start Intake (A) Camshaft Position Timing Over-Advanced (Bank 1) - no sub type information
  • Engine oil pressure too low
  • Intake valve solenoid 1 circuit short to ground, open circuit, high resistance
  • Intake valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check intake valve solenoid 1 sensor circuit for short to ground, open circuit, high resistance. Check and install a new intake valve solenoid 1 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P052B-00 Cold Start Intake (A) Camshaft Position Timing Over-Retarded (Bank 1) - no sub type information
  • Engine oil pressure too low
  • Intake valve solenoid 1 circuit short to ground, open circuit, high resistance
  • Intake valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check intake valve solenoid 1 sensor circuit for short to ground, open circuit, high resistance. Check and install a new intake valve solenoid 1 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P052C-00 Cold Start Intake (A) Camshaft Position Timing Over-Advanced (Bank 2) - no sub type information
  • Engine oil pressure too low
  • Intake valve solenoid 2 circuit short to ground, open circuit, high resistance
  • Intake valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check intake valve solenoid 2 sensor circuit for short to ground, open circuit, high resistance. Check and install a new intake valve solenoid 2 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P052D-00 Cold Start Intake (A) Camshaft Position Timing Over-Retarded (Bank 2) - no sub type information
  • Engine oil pressure too low
  • Intake valve solenoid 2 circuit short to ground, open circuit, high resistance
  • Intake valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check intake valve solenoid 2 sensor circuit for short to ground, open circuit, high resistance. Check and install a new intake valve solenoid 2 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P054A-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 1) - no sub type information
  • Engine oil pressure too low
  • Exhaust valve solenoid 1 circuit short to ground, open circuit, high resistance
  • Exhaust valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 sensor circuit for short to ground, open circuit, high resistance. Check and install a new exhaust valve solenoid 1 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P054B-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 1) - no sub type information
  • Engine oil pressure too low
  • Exhaust valve solenoid 1 circuit short to ground, open circuit, high resistance
  • Exhaust valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 sensor circuit for short to ground, open circuit, high resistance. Check and install a new exhaust valve solenoid 1 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P054C-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 2) - no sub type information
  • Engine oil pressure too low
  • Exhaust valve solenoid 2 circuit short to ground, open circuit, high resistance
  • Exhaust valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 sensor circuit for short to ground, open circuit, high resistance. Check and install a new exhaust valve solenoid 2 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P054D-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 2) - no sub type information
  • Engine oil pressure too low
  • Exhaust valve solenoid 2 circuit short to ground, open circuit, high resistance
  • Exhaust valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
 Check engine oil level and top up as required. Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 sensor circuit for short to ground, open circuit, high resistance. Check and install a new exhaust valve solenoid 2 sensor as required. Check service history /mileage. Check and install new timing chains as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0560-13 System Voltage- circuit open
  • Engine Control Module (ECM) power supply circuit, open circuit
  • Engine Control Module (ECM) battery monitor disconnected
 Refer to the electrical circuit diagrams and check Engine Control Module (ECM) power supply circuit for open circuit. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) battery monitor circuit for open circuit.
P0562-00 System Voltage Low - no sub type information
  • Battery circuit high resistance
  • Alternator circuit open circuit, high resistance
  • Alternator failure
 Refer to the electrical circuit diagrams and check battery circuit for high resistance. Refer to the electrical circuit diagrams and check alternator circuit for open circuit, high resistance. Check and install a new alternator as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0563-00 System Voltage High - no sub type information
  • Battery circuit high resistance
  • Alternator over charging
 Refer to the electrical circuit diagrams and check battery circuit for high resistance. Check and install a new alternator as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0572-17 Brake Switch A Circuit Low - circuit voltage above threshold
  • Brake switch 2 sense circuit short circuit to ground
  • Brake switch 2 failure
 Refer to the electrical circuit diagrams and check brake switch 2 circuit for short to ground. Check and install a new brake switch 2 as required.
P0573-16 Brake Switch A Circuit High - circuit voltage below threshold
  • Brake switch 1 sense circuit short circuit to ground
  • Brake switch 2 sense circuit open circuit
  • Brake switch 2 failure
 Refer to the electrical circuit diagrams and check brake switch 1 circuit for open circuit. Refer to the electrical circuit diagrams and check brake switch 2 circuit for open circuit. Check and install a new brake switch 2 as required.
P0578-00 Cruise Control Multi-Function Input A Circuit Stuck - no sub type information
  • Cruise control circuit, output signal stuck
  • Cruise control switch stuck
 Refer to the electrical circuit diagrams and check cruise control switch circuit for short to ground. Check for stuck speed control switch, install a new switch pack as required.
P057B-87 Brake Pedal Position Sensor Circuit Range/Performance - missing message
  • Brake pressure signal missing from Anti-lock Braking System (ABS) control module
 Check the Anti-lock Braking System (ABS) control module for related DTCs and refer to the relevant DTC index.
P0590-00 Cruise Control Multi-Function Input B Circuit Stuck - no sub type information
  • Active Speed Limiter (ASL) switch stuck
 Check for Active Speed Limiter (ASL) DTCs within Gear Shift Module (GSM). Check and install a new Gear Shift Module (GSM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0600-49 Serial Communication Link - internal electronic failure
  • Corrupt Engine Control Module (ECM) software
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0601-43 Internal Control Module Memory Check Sum Error - special memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0601-45 Internal Control Module Memory Check Sum Error - program memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0604-42 Internal Control Module Random Access Memory (RAM) Error - general memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0604-43 Internal Control Module Random Access Memory (RAM) Error - Special memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0604-44 Internal Control Module Random Access Memory (RAM) Error - Data memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-00 Internal Control Module Read Only Memory (ROM) Error - no sub type information
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-29 Internal Control Module Read Only Memory (ROM) Error - signal invalid
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-42 Internal Control Module Read Only Memory (ROM) Error - general memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-44 Internal Control Module Read Only Memory (ROM) Error - data memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-46 Internal Control Module Read Only Memory (ROM) Error - calibration / parameter memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-48 Internal Control Module Read Only Memory (ROM) Error - supervision software failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0605-64 Internal Control Module Read Only Memory (ROM) Error - signal plausibility failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-01 Control Module Processor - general Electrical Failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-04 Control Module Processor - system internal failures
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-05 Control Module Processor - system programming failures
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-41 Control Module Processor - general checksum failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-42 Control Module Processor - general memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-43 Control Module Processor - special memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-44 Control Module Processor - data memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-47 Control Module Processor - watchdog / safety micro controller failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-48 Control Module Processor - supervision software failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0606-49 Control Module Processor - internal electronic failure
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0607-00 Control Module Performance - no sub type information
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0610-43 Control Module Vehicle Options Error - special memory failure
  • Corrupt Engine Control Module (ECM) software flash
  • Corrupt Rear Junction (RJB)Box software flash
  • Corrupt Central Junction Box (CJB) software flash
 Clear the DTC and re-test. Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Re-configure the Rear Junction Box (RJB) using the manufacturer approved diagnostic system. Re-configure the Central Junction Box (CJB) using the manufacturer approved diagnostic system.
P0615-13 Starter Relay Circuit - circuit open
  • Starter relay control circuit open circuit
  • Starter relay failure
 Refer to the electrical circuit diagrams and check starter relay control circuit for open circuit. Check and install a new starter relay as required.
P0616-11 Starter Relay Circuit Low - circuit short to ground
  • Starter relay control circuit short to ground
  • Starter relay failure
 Refer to the electrical circuit diagrams and check starter relay control circuit for short to ground. Check and install a new starter relay as required.
P0617-12 Starter Relay Circuit High - circuit short to battery
  • Starter relay control circuit short to power
  • Starter relay failure
 Refer to the electrical circuit diagrams and check starter relay control circuit for short to power. Check and install a new starter relay as required.
P061A-00 Internal Control Module Torque Performance - no sub type information
  • Manifold air flow sensor(s) failure
  • Electric throttle unit failure
 Check for related DTCs. Check manifold air flow sensors are reading correctly. Check and install a new manifold air flow sensor(s) as required. Check throttle position sensors are reading the same position. Check throttle body is clear of any deposits. Check and install a new electric throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P061A-04 Internal Control Module Torque Performance - System Internal Failures
  • Manifold air flow sensor(s) failure
  • Electric throttle unit failure
 Check for related DTCs. Check manifold air flow sensors are reading correctly. Check and install a new manifold air flow sensor(s) as required. Check throttle position sensors are reading the same position. Check throttle body is clear of any deposits. Check and install a new electric throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect
P061A-29 Internal Control Module Torque Performance - signal invalid
  • Intake system air leak
  • Manifold air flow sensor(s) failure
  • Electric throttle unit failure
  • Accelerator pedal position sensor failure
  • Atmospheric pressure sensor failure
 Check for related DTCs. Check intake air system for leaks. Check manifold air flow sensors are reading correctly. Check and install a new air flow sensor(s) as required. Check throttle position sensors are reading the same position. Check throttle body is clear of any deposits. Check and install a new electric throttle unit as required. Check and install a new accelerator pedal position sensor as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P061A-64 Internal Control Module Torque Performance - signal plausibility failure
  • Intake system air leak
  • Manifold air flow sensor(s) failure
 Check for related DTCs. Check intake air system for leaks and is correctly installed. Check manifold air flow sensors are reading correctly. Check and install a new manifold air flow sensor(s) as required.
P061B-62 Internal Control Module Torque Calculation Performance - signal compare failure
  • Intake system air leak
  • Engine breather system leak
  • Manifold air flow sensor failure
  • Electric throttle unit failure
  • Accelerator pedal position sensor failure
  • Atmospheric pressure sensor failure
 Check intake air system for leaks. Check engine breather system for leaks. Check and install a new manifold air flow sensor as required. Check and install a new electric throttle unit as required. Check and install a new accelerator pedal position sensor as required. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0620-01 Generator Control Circuit - General Electrical Failure
  • Generator B+ or battery terminal disconnected/poor connection
  • Charging circuit short, open circuit
  • Generator failure
 Check for good/clean contact at generator B+ and battery terminal connectors. Refer to the electrical circuit diagrams and check charging circuit for short, open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the generator, check and install a new generator as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0627-00 Fuel Pump A Control Circuit / Open - no sub type information
  • High pressure fuel pump 1 circuit to Fuel Pump Driver Module (FPDM) short to ground, power, open circuit, high resistance
 Refer to the electrical circuit diagrams and check high pressure fuel pump 1 circuit for short to ground, power, open circuit, high resistance.
P062A-00 Fuel Pump A Control Circuit Range/Performance - no sub type information
  • Invalid fuel pump duty requested by the Engine Control Module (ECM)
 Refer to the electrical circuit diagrams and check the Fuel Pump Driver Module (FPDM) circuit for short to ground, power, open circuit, high resistance.
P0630-00 VIN Not Programmed or Incompatible - ECM/PCM - no sub type information
  • Car Configuration File (CCF) to CAN VIN mismatch
  • New Engine Control Module (ECM) fitted and incorrectly configured
  • New Central Junction Box (CJB) fitted and incorrectly configured
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system, clear DTC and re-test. Re-configure the Central Junction Box (CJB) using the manufacturer approved diagnostic system. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0634-22 PCM / ECM/ TCM Internal Temperature Too High - signal amplitude > maximum
  • Engine Control Module (ECM) internal temperature too high
 Clear the DTC. With the ignition off, wait 10 minutes and re-check DTC. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0634-4B PCM / ECM / TCM Internal Temperature A Too High - over temperature
  • Engine Control Module (ECM) internal temperature too high
 Clear the DTC. With the ignition off, wait 10 minutes and re-check DTC. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0642-00 Sensor Reference Voltage A Circuit Low - no sub type information
  • Short circuit to power of a 5V output pin, either in the harness, or a connector
  • Internal short circuit in a faulty component
 Refer to the electrical circuit diagrams and check 5V supply circuit for short to ground open circuit, high resistance, terminal damage or corrosion. Check Engine Control Module (ECM) for sensor related DTCs and refer to the relevant DTC Index.
P0643-00 Sensor Reference Voltage A Circuit High - no sub type information
  • Short circuit to ground of a 5V output pin, either in the harness, or a connector
  • Internal short circuit in a faulty component
 Refer to the electrical circuit diagrams and check 5V supply circuit for short to power open circuit, high resistance, terminal damage or corrosion. Check Engine Control Module (ECM) for sensor related DTCs and refer to the relevant DTC Index.
P065B-16 Generator Control Circuit Range/Performance - circuit voltage below threshold
  • Generator B+ or battery terminal disconnected/poor connection
  • Charging circuit short, open circuit
  • Generator failure
  • Battery failure
 Check for good/clean contact at generator B+ and battery terminal connectors. Refer to the electrical circuit diagrams and check charging circuit for short, open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the generator, check and install a new generator as required. Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the service information. Refer to the warranty policy and procedures manual if a component is suspect.
P065B-17 Generator Control Circuit Range/Performance - circuit voltage above threshold
  • Charging circuit short to power
  • Generator failure
  • Battery failure
 Check for good/clean contact at generator B+ and battery terminal connectors. Refer to the electrical circuit diagrams and check charging circuit for short, open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the generator, check and install a new generator as required. Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the service information. Refer to the warranty policy and procedures manual if a component is suspect.
P065C-00 Generator Mechanical Performance - no sub type information
  • Poor front end accessory belt tension
  • Generator pulley loose/failure
  • Generator failure
 Check front end accessory belt for condition/contamination and correct tension. Check generator pulley for failure. Clear DTC and repeat automated diagnostic procedure using manufacturer approved diagnostic system. If DTC remains check and install a new generator as required. Refer to the warranty policy and procedures manual if a component is suspect.
P0660-13 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - circuit open
  • Intake manifold tuning valve circuit open circuit
 Refer to the electrical circuit diagrams and check intake manifold tuning valve circuit for open circuit.
P0661-11 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - circuit short to ground
  • Intake manifold tuning valve circuit short to ground
 Refer to the electrical circuit diagrams and check intake manifold tuning valve circuit for short to ground.
P0662-12 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - circuit short to battery
  • Intake manifold tuning valve circuit short to power
 Refer to the electrical circuit diagrams and check manifold tuning valve circuit for short to power.
P0668-00 PCM / ECM / TCM Internal Temperature Sensor A Circuit Low - no sub type information
  • Engine Control Module (ECM) internal temperature sensor failure
 Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0669-00 PCM / ECM / TCM Internal Temperature Sensor A Circuit High - no sub type information
  • Engine Control Module (ECM) internal temperature sensor failure
 Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0687-73 ECM/PCM Power Relay Control Circuit High - actuator stuck closed
  • Engine Control Module (ECM) relay circuit short to power
  • Engine Control Module (ECM) relay failure
 Refer to the electrical circuit diagrams and check Engine Control Module (ECM) relay circuit for short to power. Check and install a new Engine Control Module (ECM) relay as required.
P0695-00 Fan 3 Control Circuit Low - no sub type information
  • E-Box fan circuit short to ground
  • E-Box fan failure
 Refer to the electrical circuit diagrams and check E-Box fan circuit for short to ground. Check and install a new E-Box fan as required.
P0696-12 Fan 3 Control Circuit High - circuit short to battery
  • E-Box fan circuit short to power
  • E-Box fan failure
 Refer to the electrical circuit diagrams and check E-Box fan circuit for short to power. Check and install a new E-Box fan as required.
P0696-13 Fan 3 Control Circuit High - circuit open
  • E-Box fan circuit open circuit
  • E-Box fan failure
 Refer to the electrical circuit diagrams and check E-Box fan circuit for open circuit. Check and install a new E-Box fan as required.
P0721-85 Output Shaft Speed Sensor Circuit Range/Performance - signal above allowable range
  • Transmission Control Module (TCM) has reported a fault in the shaft speed signal
 Check Transmission Control Module (TCM) for related DTCs and refer to relevant DTC Index.
P0721-86 Output Shaft Speed Sensor Circuit Range/Performance - signal invalid
  • Transmission Control Module (TCM) has taken to 8 seconds or longer to change range
 Check Transmission Control Module (TCM) for related DTCs and refer to relevant DTC Index.
P0850-86 Park / Neutral Switch Input Circuit - signal invalid
  • Intermittent fault on Park/Neutral signal from Gear Shift Module (GSM)
  • CAN network failure between Gear Shift Module (GSM) and Engine Control Module (ECM)
 Check Gear Shift Module (GSM) for related DTCs and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check Park/Neutral switch input circuit for short to ground, power, open circuit. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P0850-8F Park / Neutral Switch Input Circuit - erratic
  • Intermittent fault on Park/Neutral signal from GSM
  • CAN network failure between Gear Shift Module (GSM) and Engine Control Module (ECM)
 Check Gear Shift Module (GSM) for related DTCs and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check Park/Neutral switch input circuit for short to ground, power, open circuit. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P0851-14 Park / Neutral Switch Input Circuit Low - circuit short to ground or open
  • Park/Neutral switch input circuit short to ground, open circuit
 Refer to the electrical circuit diagrams and check park/neutral switch input circuit for short to ground, open circuit.
P0852-12 Park / Neutral Switch Input Circuit Low - circuit short to battery
  • Park/Neutral switch input circuit short to power
 Refer to the electrical circuit diagrams and check park/neutral switch input circuit for short to power.
P0A1A-87 Generator Control Module - missing message
  • Generator to Engine Control Module (ECM) Engine Control Module (ECM) LIN circuit open circuit
  • Generator/Engine Control Module (ECM) failure
 Check for good/clean contact at generator and Engine Control Module (ECM) LIN circuit connectors/pins. Refer to the electrical circuit diagrams and check generator circuit for open circuit. Check for Engine Control Module (ECM) hardware DTCs and refer to relevant DTC Index. Clear DTCs and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains check and install a new generator/Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0A1A-88 Generator Control Module - bus off
  • Generator to Engine Control Module (ECM) Engine Control Module (ECM) LIN circuit open circuit
  • Generator/Engine Control Module (ECM) failure
 Check for good/clean contact at generator and Engine Control Module (ECM) LIN circuit connectors/pins. Refer to the electrical circuit diagrams and check generator circuit for open circuit. Check for Engine Control Module (ECM) hardware DTCs and refer to relevant DTC Index. Clear DTCs and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains check and install a new generator/Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P0A3B-68 Generator Over Temperature - event information
  • Cooling fan not operating
  • Coolant level low
 Check for correct cooling fan operation. Check coolant level. Clear DTC and re-test.
P115D-00 Mass Air Flow Circuit Offset - no sub type information
    NOTE: Customer likely to report hesitation.
  • Air cleaner blocked
  • Air intake leak
  • Engine breather blocked
  • Air intake blockage
  • Carbon build up on throttle blade
  • Mass air flow sensor circuit, high resistance
  • Blocked catalyst(s)
  • Mass air flow sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503). Check air cleaner for blockage. Check air intake system for leaks. Check engine breather system for blockages. Check for carbon build up on throttle blade. Check for related mass air flow DTCs P0102 or P0103. Refer to the electrical circuit diagrams and check mass air flow sensor circuit for high resistance. Check and install a new mass air flow sensor as required.
P1315-00 Persistent Misfire - No sub type information
  • Engine Control Module (ECM) to ignition coil primary circuit fault (cylinder misfire detected DTC also flagged)
  • Fuel injector circuit fault(s) (injector DTCs also flagged)
  • Fuel delivery pressure low
  • Spark plug failure/fouled/incorrect gap
  • Cylinder compression low
  • Exhaust system blockage
 Check for cylinder mis-fire, ignition and injector DTCs and refer to the DTC Index. Refer to the electrical circuit diagrams and check ignition coil circuit for short to ground, power, open circuit. Check for fuel system failure. Check and install a new spark plug(s) as required. Carry out cylinder compression tests. Check exhaust system for blockage.
P1316-00 Injector Driver Module Codes Detected - no sub type information
  • Engine Control Module (ECM) to ignition coil primary circuit fault (cylinder misfire detected DTC also flagged)
  • Fuel injector circuit fault(s) (injector DTCs also flagged)
  • Fuel delivery pressure low
  • Spark plug failure/fouled/incorrect gap
  • Cylinder compression low
  • Exhaust system blockage
 Check for cylinder mis-fire, ignition and injector DTCs and refer to the DTC Index. Refer to the electrical circuit diagrams and check ignition coil circuit for short to ground, power, open circuit. Check for fuel system failure. Check and install a new spark plug(s) as required. Carry out cylinder compression tests. Check exhaust system for blockage.
P1593-64 Cruise Control Monitor Fault - signal plausibility failure
  • Cruise control monitor fault. The Engine Control Module (ECM) performs a independent check of the cruise status
 Check the car configuration and contact the Jaguar Landrover help desk.
P1603-00 EEPROM Malfunction - no sub type information
  • Corrupt Engine Control Module (ECM) software flash
  • Engine Control Module (ECM) power supply fault
  • Engine Control Module (ECM) damage through water ingress
 Re-configure the Engine Control Module (ECM) using the manufacturer approved diagnostic system. Check Engine Control Module (ECM) power supply circuit for open circuit. Check Engine Control Module (ECM) for signs of water ingress. Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2088-11 A Camshaft Position Actuator Control Circuit Low Bank 1 - circuit short to ground
  • Intake valve solenoid 1 short to ground
 Refer to the electrical circuit diagrams and check intake valve solenoid 1 for short to ground.
P2089-12 A Camshaft Position Actuator Control Circuit High Bank 1 - circuit short to battery
  • Intake valve solenoid 1 short to power
 Refer to the electrical circuit diagrams and check intake valve solenoid 1 for short to power.
P2090-11 B Camshaft Position Actuator Control Circuit Low Bank 1 - circuit short to ground
  • Exhaust valve solenoid 1 short to ground
 Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 for short to ground.
P2091-12 B Camshaft Position Actuator Control Circuit High Bank 1 - circuit short to battery
  • Exhaust valve solenoid 1 short to power
 Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 for short to power.
P2092-11 A Camshaft Position Actuator Control Circuit Low Bank 2 - circuit short to ground
  • Intake valve solenoid 2 short to ground
 Refer to the electrical circuit diagrams and check intake valve solenoid 2 for short to ground.
P2093-12 A Camshaft Position Actuator Control Circuit High Bank 2 - circuit short to battery
  • Intake valve solenoid 2 short to power
 Refer to the electrical circuit diagrams and check intake valve solenoid 2 for short to power.
P2094-11 B Camshaft Position Actuator Control Circuit Low Bank 2 - circuit short to ground
  • Exhaust valve solenoid 2 short to ground
 Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 for short to ground.
P2095-12 B Camshaft Position Actuator Control Circuit High Bank 2 - circuit short to battery
  • Exhaust valve solenoid 2 short to power
 Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 for short to power.
P2096-00 Post Catalyst Fuel Trim System Too Lean Bank 1 - no sub type information
  • Post catalyst oxygen sensor odd, sensing circuit short to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor odd, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to ground, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check for air leak between the two oxygen sensors. Check and install new post catalyst oxygen sensor odd, as required.
P2097-00 Post Catalyst Fuel Trim System Too Rich Bank 1 - no sub type information
  • Post catalyst oxygen sensor odd, sensing circuit short to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor odd, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short to ground, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check for air leak between the two oxygen sensors. Check and install new post catalyst oxygen sensor odd, as required.
P2098-00 Post Catalyst Fuel Trim System Too Lean Bank 2 - no sub type information
  • Post catalyst oxygen sensor even, sensing circuit short to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor even, sensing circuit for short to ground, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check for air leak between the two oxygen sensors. Check and install new post catalyst oxygen sensor even, as required.
P2099-00 Post Catalyst Fuel Trim System Too Rich Bank 2 - no sub type information
  • Post catalyst oxygen sensor even, sensing circuit short to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor even, failure
 Refer to the electrical circuit diagrams and check post catalyst oxygen sensor even, sensing circuit for short to ground, high resistance, open circuit. Check for air leak between catalyst and exhaust manifold. Check for air leak between the two oxygen sensors. Check and install new post catalyst oxygen sensor even, as required.
P2105-00 Throttle Actuator Control System - Forced Engine Shutdown - no sub type information
  • Engine speed or torque limitation has been activated as a result of Engine Control Module (ECM), throttle pedal position sensor, or torque faults
 Check for any DTCs referring to Engine Control Module (ECM), throttle pedal position sensor, or torque faults.
P2118-19 Throttle Actuator Control Motor Current Range/Performance - circuit current above threshold
  • Throttle motor control circuit short to ground, power, high resistance
  • Engine Control Module (ECM) ground circuit fault
  • Carbon build-up on throttle blade
  • Electronic throttle unit failure
 Refer to the electrical circuit diagrams and check electric throttle unit circuit for short to ground, power, high resistance. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) ground circuit for faults. Make sure throttle blade is clean of carbon. Check the system is operating correctly and the DTC does not return. Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2119-00 Throttle Actuator Control Throttle Body Range/Performance - no sub type information
  • Carbon build-up on throttle blade
  • Engine Control Module (ECM) ground circuit fault
  • Electronic throttle unit return spring faulty
  • Electronic throttle unit limp home spring faulty
 Make sure throttle blade is clean of carbon. Refer to the electrical circuit diagrams and check Engine Control Module (ECM) ground circuit for faults. Check the system is operating correctly and the DTC does not return. Suspect electronic throttle unit faulty. Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2119-29 Throttle Actuator Control Throttle Body Range/Performance - signal invalid
  • Stuck / sticking throttle blade
  • Electric throttle unit failure
 Ensure throttle blade is free of build-up / other obstructions. Suspect electric throttle unit faulty. Check and install a new electric throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2119-64 Throttle Actuator Control Throttle Body Range/Performance - signal plausibility failure
  • Stuck / sticking throttle blade
  • Electric throttle unit failure
 Ensure throttle blade is free of build-up / other obstructions. Suspect electric throttle unit faulty. Check and install a new electric throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2122-00 Throttle/Pedal Position Sensor/Switch D Circuit Low - no sub type information
  • Electronic throttle unit, throttle position sensor 1 circuit short to ground, open circuit
  • Electronic throttle unit, VREF circuit open circuit
  • Electronic throttle unit, throttle position sensor 1 failure
 Refer to the electrical circuit diagrams and check electronic throttle unit, throttle position sensor 1 circuit for short to ground, open circuit. Check electronic throttle unit, VREF circuit for open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2123-00 Throttle/Pedal Position Sensor/Switch D Circuit High - no sub type information
  • Electronic throttle unit, throttle position sensor 1 circuit short to power
  • Electronic throttle unit, GREF circuit open circuit
  • Electronic throttle unit, throttle position sensor 1 failure
 Refer to the electrical circuit diagrams and check electronic throttle unit, throttle position sensor 1 circuit for short to power. Check electronic throttle unit, GREF circuit for open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2127-00 Throttle/Pedal Position Sensor/Switch E Circuit Low - no sub type information
  • Electronic throttle unit, throttle position sensor 2 circuit short to ground, open circuit
  • Electronic throttle unit, VREF circuit open circuit
  • Electronic throttle unit, throttle position sensor 2 failure
 Refer to the electrical circuit diagrams and check electronic throttle unit, throttle position sensor 2 circuit for short to ground, open circuit. Check electronic throttle unit, VREF circuit for open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2128-00 Throttle/Pedal Position Sensor/Switch E Circuit High - no sub type information
  • Electronic throttle unit, throttle position sensor 2 circuit short to power
  • Electronic throttle unit, GREF circuit open circuit
  • Electronic throttle unit, throttle position sensor 2 failure
 Refer to the electrical circuit diagrams and check electronic throttle unit, throttle position sensor 2 circuit for short to power. Check electronic throttle unit, GREF circuit for open circuit. Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit, check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual if a component is suspect.
P2135-00 Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation - no sub type information
  • Throttle pedal position sensor circuit 1 and 2 short to ground, short to power, open circuit
 Refer to the electrical circuit diagrams and check throttle pedal position sensor circuit 1 and 2 for short to ground, short to power, open circuit.
P2135-09 Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation - Component Failures
  • Throttle pedal position sensor circuit 1 and 2 short to ground, short to power, open circuit
 Refer to the electrical circuit diagrams and check throttle pedal position sensor circuit 1 and 2 for short to ground, short to power, open circuit.
P2138-64 Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation - No sub type information
  • Analogue Pedal Position (APP) sensor circuit 1 and 2 short to ground, short to power, open circuit
 Refer to the electrical circuit diagrams and check Analogue Pedal Position (APP) sensor circuit 1 and 2 for short to ground, short to power, open circuit.
P2183-23 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - signal stuck low
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit
  • Engine coolant temperature sensor 2 failure
 Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit. Check and install a new engine coolant temperature sensor 2 as required.
P2183-24 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - signal stuck high
  • Engine coolant temperature sensor 2 circuit short to power
  • Engine coolant temperature sensor 2 failure
 Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for short to power. Check and install a new engine coolant temperature sensor 2 as required.
P2183-29 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - signal invalid
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit, short to ground, short to power
  • Engine coolant temperature sensor 2 failure
 Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit, short to ground, short to power. Check and install a new engine coolant temperature sensor 2 as required.
P2184-16 Engine Coolant Temperature Sensor 2 Circuit Low - circuit voltage below threshold
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit
  • Engine coolant temperature sensor 2 failure
 Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit. Check and install a new engine coolant temperature sensor 2 as required.
P2185-17 Engine Coolant Temperature Sensor 2 Circuit High - circuit voltage above threshold
  • Ignition turned on with an ambient temperature of below -40c
  • Engine coolant temperature sensor 2 circuit short to power
  • Engine coolant temperature sensor 2 failure
 Clear the DTC and re-test. Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for short to power. Check and install a new engine coolant temperature sensor 2 as required.
P2228-00 Barometric Pressure Circuit Low - no sub type information
  • Barometric pressure sensor failure (internal Engine Control Module (ECM) fault)
 Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A). Suspect the Engine Control Module (ECM). Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2229-00 Barometric Pressure Circuit Low - no sub type information
  • Barometric pressure sensor failure (internal Engine Control Module (ECM) fault)
 Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A). Suspect the Engine Control Module (ECM). Check and install a new Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2279-00 Intake Air System Leak - no sub type information
  • Part load breather pipe disconnected
  • Brake vacuum pipe disconnected
  • Excessive intake air leak
 Check for related DTCs. Check part load breather pipe for leaks or disconnected. Check brake vacuum pipe for leaks or disconnected. Check intake air system for leaks.
P2300-11 Ignition Coil A Primary Control Circuit Low - circuit short to ground
  • Ignition coil 1 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 1 circuit for short to ground.
P2301-12 Ignition Coil A Primary Control Circuit Low - circuit short to battery
  • Ignition coil 1 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 1 circuit for short to power.
P2303-11 Ignition Coil B Primary Control Circuit Low - circuit short to ground
  • Ignition coil 2 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 2 circuit for short to ground.
P2304-12 Ignition Coil B Primary Control Circuit Low - circuit short to battery
  • Ignition coil 2 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 2 circuit for short to power.
P2306-11 Ignition Coil C Primary Control Circuit Low - circuit short to ground
  • Ignition coil 3 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 3 circuit for short to ground.
P2307-12 Ignition Coil C Primary Control Circuit Low - circuit short to battery
  • Ignition coil 3 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 3 circuit for short to power.
P2309-11 Ignition Coil D Primary Control Circuit Low - circuit short to ground
  • Ignition coil 4 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 4 circuit for short to ground.
P2310-12 Ignition Coil D Primary Control Circuit Low - circuit short to battery
  • Ignition coil 4 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 4 circuit for short to power.
P2312-11 Ignition Coil E Primary Control Circuit Low - circuit short to ground
  • Ignition coil 5 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 5 circuit for short to ground.
P2313-12 Ignition Coil E Primary Control Circuit Low - circuit short to battery
  • Ignition coil 5 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 5 circuit for short to power.
P2315-11 Ignition Coil F Primary Control Circuit Low - circuit short to ground
  • Ignition coil 6 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 6 circuit for short to ground.
P2316-12 Ignition Coil F Primary Control Circuit Low - circuit short to battery
  • Ignition coil 6 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 6 circuit for short to power.
P2318-11 Ignition Coil G Primary Control Circuit Low - circuit short to ground
  • Ignition coil 7 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 7 circuit for short to ground.
P2319-12 Ignition Coil G Primary Control Circuit Low - circuit short to battery
  • Ignition coil 7 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 7 circuit for short to power.
P2321-11 Ignition Coil H Primary Control Circuit Low - circuit short to ground
  • Ignition coil 8 circuit short to ground
 Refer to the electrical circuit diagrams and check ignition coil 8 circuit for short to ground.
P2322-12 Ignition Coil H Primary Control Circuit Low - circuit short to battery
  • Ignition coil 8 circuit short to power
 Refer to the electrical circuit diagrams and check ignition coil 8 circuit for short to power.
P2401-00 Evaporative Emission System Leak Detection Pump Control Circuit Low - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) fuse failure
  • Diagnostic Module Tank Leakage (DMTL) circuit short to ground, open circuit
  • Diagnostic Module Tank Leakage (DMTL) failure
 Check Diagnostic Module Tank Leakage (DMTL) fuse for failure and security in holder. Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) circuit for short to ground, open circuit. Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2402-00 Evaporative Emission System Leak Detection Pump Control Circuit High - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) circuit short to power
  • Diagnostic Module Tank Leakage (DMTL) failure
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) circuit for short to power. Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2404-29 Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance - Signal invalid
  • Diagnostic Module Tank Leakage (DMTL) failure
 Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2404-2F Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance - signal erratic
  • Diagnostic Module Tank Leakage (DMTL) failure
 Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2405-00 Evaporative Emission System Leak Detection Pump Sense Circuit Low - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) circuit short to ground, high resistance, open circuit
  • Diagnostic Module Tank Leakage (DMTL) failure
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) circuit for short to ground, high resistance, open circuit. Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2406-00 Evaporative Emission System Leak Detection Pump Sense Circuit High - no sub type information
  • Blockage in Diagnostic Module Tank Leakage (DMTL) ventilation pipe
  • Diagnostic Module Tank Leakage (DMTL) circuit, open circuit
 Check for blockage in the Blockage in Diagnostic Module Tank Leakage (DMTL) ventilation pipe. Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P240A-00 Evaporative Emission System Leak Detection Pump Heater Circuit / Open - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) circuit, open circuit
  • Diagnostic Module Tank Leakage (DMTL) failure
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) heater circuit for open circuit. Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P240B-00 Evaporative Emission System Leak Detection Pump Heater Circuit Low - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) heater circuit short to ground, high resistance
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) heater circuit for short to ground, high resistance.
P240C-00 Evaporative Emission System Leak Detection Pump Heater Circuit High - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) heater circuit short to power
 Refer to the electrical circuit diagrams and check Diagnostic Module Tank Leakage (DMTL) heater circuit for short to power.
P2450-00 Evaporative Emission Control System Switching Valve Performance/Stuck Open - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) failure
 Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2451-00 Evaporative Emission Control System Switching Valve Performance/Stuck Closed - no sub type information
  • Diagnostic Module Tank Leakage (DMTL) failure
 Check and install a new Diagnostic Module Tank Leakage (DMTL) as required. Refer to the warranty policy and procedures manual if a module is suspect.
P250C-23 Engine Oil Level Sensor Circuit Low - signal stuck low
  • Oil temperature level sensor circuit short to ground
  • Oil temperature level sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3). Refer to the electrical circuit diagrams and check oil temperature level sensor circuit for short to ground. Check and install a new oil temperature level sensor as required. Refer to the warranty policy and procedures manual if a module is suspect.
P250D-24 Engine Oil Level Sensor Circuit High - signal stuck high
  • Oil temperature level sensor circuit short to power
  • Oil temperature level sensor failure
 Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3). Refer to the electrical circuit diagrams and check oil temperature level sensor circuit for short to power. Check and install a new oil temperature level sensor as required. Refer to the warranty policy and procedures manual if a module is suspect.
P2544-64 Torque Management Request Input Signal A - signal plausibility failure
  • Inappropriate request from Anti-lock Braking System (ABS)
 Check for related DTCs within Anti-lock Braking System (ABS) module and refer to the relevant DTC index. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P2544-92 Torque Management Request Input Signal A - performance or incorrect operation
  • Inappropriate request from Anti-lock Braking System (ABS)
 Check for related DTCs within Anti-lock Braking System (ABS) module and refer to the relevant DTC index. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P2610-00 ECM/PCM Internal Engine Off Timer Performance - no sub type information
  • Instrument Panel Cluster (IPC) fault
  • Central Junction Box (CJB) fault
  • CAN network error
 Check for DTCs related to any of the components listed and refer to relevant DTC Index. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P2610-84 ECM/PCM Engine Off Timer Performance - signal below allowable range
  • Instrument Panel Cluster (IPC) fault
  • Central Junction Box (CJB) fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • Low battery voltage
  • CAN network error
 Check for DTCs related to any of the components listed and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, power, open circuit. Check the battery voltage, repair as required. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P2610-85 ECM/PCM Engine Off Timer Performance - signal above allowable range
  • Instrument Panel Cluster (IPC) fault
  • Central Junction Box (CJB) fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • Low battery voltage
  • CAN network error
 Check for DTCs related to any of the components listed and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short to ground, power, open circuit. Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, power, open circuit. Check the battery voltage, repair as required. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
P2610-87 ECM/PCM Internal Engine Off Timer Performance - missing message
  • Instrument Panel Cluster (IPC) fault
  • Central Junction Box (CJB) fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • CAN network error
 Check for DTCs related to any of the components listed, and refer to relevant DTC Index, refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short to ground, power, open circuit, refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short to ground, power, open circuit, carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0001-88 High Speed CAN Communication Bus - bus off
  • High speed CAN bus circuit, short to ground
  • High speed CAN bus circuit, short to power
  • High speed CAN bus, open circuit
 Refer to the electrical circuit diagrams and check CAN network for short to ground, power, open circuit. Using the manufacturer approved diagnostic system, carry out network integrity test.
U0101-00 Lost Communication with TCM - no sub type information
  • CAN link Engine Control Module (ECM)/Transmission Control Module (TCM) network malfunction
  • Transmission Control Module (TCM) fault
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM) for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check Transmission Control Module (TCM) power and ground circuit for open circuit. Check CAN harness to Transmission Control Module (TCM), repair as necessary.
U0103-00 Lost Communication with Gear Shift Control Module A - no sub type information
  • CAN link Engine Control Module (ECM)/Gear Shift Module (GSM) network malfunction
 Refer to the electrical wiring diagrams and check power and ground connections to the Gear Shift Module (GSM). Carry out the CAN integrity tests using the manufacturer approved diagnostic tool.
U0104-00 Lost Communication With Cruise Control Module - no sub type information
  • Vehicle configured for speed control, but speed control module is not installed
  • CAN Link Engine Control Module (ECM)/speed control module network malfunction
  • Speed control module power or ground circuit, open circuit
 Check vehicle has correct speed control module installed. Using the manufacturer approved diagnostic system, check speed control module, Anti-lock Braking System (ABS) module for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check speed control module power and ground circuit for open circuit. Check CAN harness to speed control module, repair as necessary.
U0121-00 Lost Communication With Anti-lock Braking System (ABS) Control Module - no sub type information
  • CAN Link Engine Control Module (ECM)/Anti-lock Braking System (ABS) module network malfunction
  • Anti-lock Braking System (ABS) module power or ground circuit, open circuit
 Using the manufacturer approved diagnostic system, check Anti-lock Braking System (ABS) module for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check Anti-lock Braking System (ABS) module power and ground circuit for open circuit. Check CAN harness to Anti-lock Braking System (ABS) module, repair as necessary.
U0128-00 Lost Communication With Park Brake Control Module - no sub type information
  • CAN Link Engine Control Module (ECM)/Electronic Parking Brake (EPB) signal missing network malfunction
 Refer to the electrical circuit diagrams and check power and ground supplies to Electronic Parking Brake (EPB). Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0132-00 Lost Communication with Suspension Control Module A - no sub type information
  • CAN link/suspension control module network malfunction
 Refer to the electrical circuit diagrams and check power and ground supplies to suspension control module. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0151-00 Lost Communication with Restraints Control Module - no sub type information
  • Lost communication with Restraints Control Module (RCM) over CAN or hardwired link
 Refer to the electrical circuit diagrams and check power and ground supplies to restraints control module. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0151-87 Lost Communication with Restraints Control Module - missing message
  • Lost communication due to Restraints Control Module (RCM) fault
 Check Restraints Control Module for associated DTCs and refer to relevant DTC Index. Refer to the electrical circuit diagrams and check power and ground supplies to restraints control module. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0155-00 Lost Communication with Instrument Panel Cluster (IPC) - no sub type information
  • CAN link between Engine Control Module (ECM) and Instrument Panel Cluster (IPC) fault
 Refer to the electrical circuit diagrams and check power and ground supplies to Instrument Panel Cluster. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0167-00 Lost Communication with Vehicle Immobilizer Control Module - no sub type information
  • Security challenge response timeout
  • Battery fault
 Refer to the electrical circuit diagrams and check power and ground supplies to the Electric Steering Column Lock (ESCL). Check for related CAN DTCs and refer to the relevant DTC index. Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the service information. Carry out the CAN network integrity test using the manufacturer approved diagnostic system.
U0300-00 Internal Control Module Software Incompatibility - no sub type information
  • Engine Control Module (ECM) has incorrect software installed
  • The Engine Control Module (ECM) is in expulsion mode. An incorrect specification Engine Control Module (ECM) has been installed to the vehicle
 Check and install the correct Engine Control Module (ECM) software. Check and install the correct Engine Control Module (ECM) as required. Refer to the warranty policy and procedures manual if a module is suspect.
U0402-00 Invalid Data Received From Transmission Control Module - no sub type information
  • Transmission Engine Control Module (ECM) request corruption
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM), for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short, open circuit.
U0402-08 Invalid Data Received from TCM - bus signal / message failures
  • Transmission Engine Control Module (ECM) request corruption
  • High speed CAN bus circuit failure, short, open circuit
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM), for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short, open circuit.
U0402-64 Invalid Data Received from TCM - Signal plausibility failure
  • Transmission to Engine Control Module (ECM) request corruption
  • High speed CAN bus signal corruption
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM), for DTCs and refer to the relevant DTC Index. Using the manufacturer approved diagnostic system, carry out network integrity test. Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short, open circuit.
U0402-82 Invalid Data Received from TCM - alive / sequence counter incorrect / not updated
  • Transmission Control Module (TCM) shaft-speed faults
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM), for DTCs and refer to the relevant DTC Index.
U0402-83 Invalid Data Received from TCM - Value of signal protection calculation incorrect
  • Transmission Control Module (TCM) shaft-speed faults
 Using the manufacturer approved diagnostic system, check Transmission Control Module (TCM), for DTCs and refer to the relevant DTC Index.
U0415-00 Invalid Data Received From Anti-lock Braking System (ABS) Control Module - no sub type information
  • Electronic throttle unit, throttle position sensor 1 failure
  • Electronic throttle unit, throttle position sensor 2 failure
  • Electronic throttle unit harness short, open circuit
 Using the manufacturer approved diagnostic system, check for electronic throttle unit DTCs repair as necessary. Refer to the electrical circuit diagrams and check electronic unit harness for short circuit, open circuit. Refer to the warranty policy and procedures manual if a module is suspect, if the electronic throttle unit is suspect.
U0415-64 Invalid Data Received From Anti-lock Braking System (ABS) (ABS) Control Module - signal plausibility failure
  • Invalid request from Anti-lock Braking System (ABS)
  • Torque up request higher than expected from Anti-lock Braking System (ABS)
 Using the manufacturer approved diagnostic system, check Anti-lock Braking System (ABS), for DTCs and refer to the relevant DTC Index. Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short, open circuit.
U0415-67 Invalid Data Received From Anti-lock Braking System (ABS) (ABS) Control Module - signal incorrect after event
  • Torque up request higher than expected from Anti-lock Braking System (ABS)
 Using the manufacturer approved diagnostic system, check Anti-lock Braking System (ABS), for DTCs and refer to the relevant DTC Index. Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short, open circuit.
U0426-00 Invalid Data Received From Vehicle Immobilizer Control Module - no sub type information
  • Security code mis-match
  • This DTC will be logged if the encrypted data exchange does not match between Engine Control Module (ECM) and the Instrument Panel Cluster (IPC) or Central Junction Box (CJB)
 Check CAN network between Engine Control Module (ECM), Instrument Panel Cluster (IPC) and Central Junction Box (CJB). Refer to the electrical circuit diagrams and check power and ground circuit to Engine Control Module (ECM) and Instrument Panel Cluster (IPC). Check correct Engine Control Module (ECM) and Instrument Panel Cluster (IPC) installed. Re-synchronise ID by re-configuring the Engine Control Module (ECM) and Instrument Panel Cluster (IPC) as new modules.
U0447-81 Invalid Data Received From Gateway "A" - invalid serial data received
  • The LIN to high speed CAN gateway has informed the Engine Control Module (ECM) of a failure
 This DTC has been inhibited in the Engine Control Module (ECM), as the LIN bus flag is set during normal operation.
scientia non olet · About LEMON Manuals