LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2012 >> XF Supercharged >> Repair and Diagnosis (Single Page) >> Engine Mechanical >> Mechanical >> Engine System - General Information -- XF/X250 >> Engine System - General Information >> Diagnosis And Testing >> Engine - v8 - 5.0L Petrol/V8 S/C 5.0L Petrol >> Symptom Chart

Symptom Chart

SYMPTOM POSSIBLE CAUSES ACTION
Engine starting poor/difficult - Engine hot or cold
  • Engine system fault
  • Engine mechanical fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index
  • Perform general engine checks:
    • Perform the Inline diagnostic unit 2, relative compression test - V8 5.0L S/C Petrol
    • Compression test. Refer to component tests in this section
    • Valve clearances
    • Spark plug condition and color
Engine idle poor
  • Engine system fault
  • Intake system leak
  • Engine mechanical fault
  • Exhaust system restricted
  • Intake/fuel system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index
  • Check the intake system for leaks. Rectify as necessary
  • Perform general engine checks:
    • Perform the Inline diagnostic unit 2, relative compression test - V8 5.0L S/C Petrol
    • Compression test. Refer to component tests in this section
    • Valve clearances
    • Spark plug condition and color
    • Carry out a vacuum gauge check. Refer to component tests in this section
  • Check the exhaust system for restrictions or blockages. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signals for long term and short term fuel trim
    • Readings up to 10%: may be considered as acceptable if the readings are equal bank to bank
    • Positive readings of between 10-20%: check for air leaks in air intake system
    • Negative readings of between 10-20%: check for over fuelling e.g. leaking injectors, high fuel pressure
    • Readings above 20%: check for DTCs and refer to DTC Index in section 100-00
Engine performance poor
  • Engine system fault
  • Intake system leak
  • Engine mechanical fault
  • Exhaust system restricted
  • Intake/fuel system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index
  • Check the intake system for leaks. Rectify as necessary
  • Perform general engine checks:
    • Perform the Inline diagnostic unit 2, relative compression test - V8 5.0L S/C Petrol
    • Compression test. Refer to component tests in this section
    • Valve clearances
    • Spark plug condition and color
    • Carry out a vacuum gauge check. Refer to component tests in this section
  • Check the exhaust system for restrictions or blockages. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signals for long term and short term fuel trim
  • Readings up to 10%: may be considered as acceptable if the readings are equal bank to bank
  • Positive readings of between 10-20%: check for air leaks in air intake system
  • Negative readings of between 10-20%: check for over fuelling e.g. leaking injectors, high fuel pressure
  • Readings above 20%: check for DTCs and refer to DTC Index in section 100-00
Engine oil consumption excessive
  • Engine oil leak
  • Positive crankcase ventilation system leaking/blocked
  • Engine mechanical fault
  • Check for engine oil leaks. Rectify as necessary
  • Check the integrity of the positive crankcase ventilation system. Rectify as necessary
  • Perform an engine oil consumption test. Refer to the component tests in this section. If oil consumption is excessive, perform general engine checks:
    • Perform the Inline diagnostic unit 2, relative compression test - V8 5.0L S/C Petrol
    • Compression test. Refer to component tests in this section
    • Valve clearances
    • Spark plug condition and color
    • Carry out a vacuum gauge check. Refer to component tests in this section