LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2011 >> XK 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 118 (Pre-Delivery Inspection Manual -- XK/X150) >> Pre-Delivery Inspection Manual >> Road Test >> Description And Operation >> Pre-Road Test >> Navigation System Setup

Navigation System Setup

WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2015 Jaguar XKR-S, 2015 Jaguar XKR, 2015 Jaguar XK, 2014 Jaguar XKR-S, and 2014 Jaguar XKR. However, it is still accessible from the selected car via links, so may be relevant.

The navigation system map DVD and language for the applicable country will require setting before use. Once setup, test the navigation system during the road test. The procedure below is used to load the applicable navigation system map DVD and set the required language.

The navigation system (if installed) comprises the Touch-Screen Display (TSD) unit that is located in the center console, and the navigation computer that is located in the luggage compartment.

The map DVDs are supplied with the vehicle literature pack. There are 2 map DVD's for NAS. Make sure the correct disc for the region is selected.

Do not attempt to load two discs into the unit.  Place the DVD case and unused discs in the driver seat rear pocket.

NOTE: The navigation system measurement units are set when the vehicle settings are setup. The language setting is not shared between the vehicle settings and navigation system and therefore requires setting independently.

Setting up the navigation system:

  1. Switch on the ignition.
  2. At the luggage compartment, open the flap housed within the rear luggage compartment forward trim panel and gain access to the navigation computer (refer to illustration NAVIGATION COMPUTER - Luggage Compartment View ).
  3. Make sure the navigation computer DVD tray is unlocked (1  ). Press the eject hard-button (2  ), located on the LH side of the navigation computer fascia panel.
  4. Load the applicable map DVD with the printed side facing up. Make sure moisture or foreign objects do not enter the DVD slot. The map DVD is automatically withdrawn into the navigation computer.
  5. Slide the navigation computer DVD tray lock/unlock  hard-button (1  ) to the locked position. Close the flap on the luggage compartment forward trim panel.
  6. At the Touch-Screen display, press the On/Off  hard-button on the console to switch the system on.
  7. If required, press the Home  hard-button to return to the home screen.
  8. Press the Navigation  soft-button to display the navigation screen.
  9. A window will now appear displaying a caution message (refer to illustration Agree Screen ).
  10. Read the caution and press the Agree  soft-button. If the language requires changing, press the Language  soft-button. If the Language  soft-button is selected the screen will return to the Navigation  menu. Press the Menu  soft-button (refer to illustration Menu Screen ) and then select the required language to be set. Follow the on-screen instruction to set the desired language. Press the 'Back  ' arrow softbutton to return to the Navigation screen. The caution message is displayed again, press the Agree  soft-button to accept the message.
  11. After pressing the Agree  soft-button, the navigation Menu  screen is displayed. A map is also displayed on the RH side of the Menu  screen (refer to illustration Menu Screen ).
  12. If required and during the road test, drive the vehicle to an open location where the GPS (Global Positioning System) satellite signals are able to be received. A GPS symbol may appear at the top of the screen. This symbol normally indicates poor signal reception but also appears if the system requires initialization, such as after transportation (the map location will also be shown incorrect).
  13. Leave the vehicle ignition switched on for 15 minutes. The navigation system will proceed to initialize automatically; resulting in the GPS symbol not being displayed and the map will display the correct location. If the correct location is still not shown, refer to 'Calibration  ' in the Navigation System handbook.
  14. From the Menu screen, press the Destination Entry  menu softbutton (refer to illustration Destination Entry Screen ).
  15. Touch the Search Area soft-button to select the search area  menu for the applicable world region (i.e. Europe). For Australia proceed to

    Step  17. The current area is shown highlighted on the map and the countries covered are listed at the bottom of the screen.

  16. From the list displayed, select the soft-button required for the area in which the vehicle is to be driven. If a new area is selected, the screen shows the new area highlighted and the list of particular countries covered.
  17. Changing search area in Australia: Press the Search Area  softbutton. The current area selected is shown highlighted on the map. From the three soft-buttons displayed, select the soft-button required for the new area. The screen shows the new area highlighted.
  18. Press the OK  soft-button. The screen returns to the Destination Entry  menu.
  19. Press the Home hard-button on the Touch-Screen console to return to the home screen.
  20. Prior to the road test, set the navigation system to the known road test route. Check that the navigation system functions correctly.
scientia non olet · About LEMON Manuals