Rear Stabilizer Bar (64.35.08): Installation

All vehicles 

1. Install the stabilizer bar.
   • Tighten to 55 Nm.
     Fig 1: Locating Stabilizer Bar

     Courtesy of JAGUAR CARS, INC.
NOTE: Right-hand shown left-hand similar.
2. Install the stabilizer bar link retaining nut.
   • Tighten to 48 Nm.
     Fig 2: Locating Stabilizer Bar Link Retaining Nut

     Courtesy of JAGUAR CARS, INC.
NOTE: Left-hand shown right-hand similar.
Fig 3: Locating Stabilizer Bar Link Retaining Nut Dust Cover
Courtesy of JAGUAR CARS, INC.
3. Install the stabilizer bar link retaining nut dust cover.
4. Reposition the subframe.
NOTE: Left-hand shown right-hand similar.
5. Install the subframe front mount retaining bolt.
   • Tighten to 125 Nm.
     Fig 4: Locating Subframe Front Mount Retaining Bolt

     Courtesy of JAGUAR CARS, INC.
NOTE: Left-hand shown right-hand similar.
6. Install the subframe rear mount retaining bolt.
   • Tighten to 125 Nm.
     Fig 5: Locating Subframe Rear Mount Retaining Bolt

     Courtesy of JAGUAR CARS, INC.
NOTE: Left-hand shown right-hand similar.
7. Install the Noise, Vibration and Harshness brace retaining bolts.
   • Tighten to 48 Nm.
     Fig 6: Locating Noise, Vibration And Harshness Brace Retaining Bolts

     Courtesy of JAGUAR CARS, INC.
8. Remove the special tool from the rear subframe.
   Fig 7: Supporting Rear Subframe With Special Tool (HTJ 1200-2)

   Courtesy of JAGUAR CARS, INC.
9. Connect the electric parking brake motor electrical connector.
   Fig 8: Locating Electric Parking Brake Motor Electrical Connector

   Courtesy of JAGUAR CARS, INC.
10. Attach the electric parking brake motor harness.
    Fig 9: Locating Electric Parking Brake Motor Harness

    Courtesy of JAGUAR CARS, INC.
11. Attach the fuel filler pipe.
    • Fit and tighten new hose clip.
      Fig 10: Locating Fuel Filler Pipe Hose Clip

      Courtesy of JAGUAR CARS, INC.
12. Attach the driveshaft to the rear drive axle flange.
    • Tighten to 88 Nm.
      Fig 11: Locating Rear Drive Axle Flange Nuts And Bolts

      Courtesy of JAGUAR CARS, INC.
NOTE: Left-hand shown right-hand similar.
Fig 12: Locating Anti-Lock Brake System (ABS) Sensor Electrical Connector
Courtesy of JAGUAR CARS, INC.
13. Connect the ABS sensor electrical connector.

Vehicles without Brembo brakes 

14. Attach the brake caliper.
    • Install new brake caliper retaining bolts.
    • Tighten to 103 Nm.
      Fig 13: Locating Brake Caliper Retaining Bolts

      Courtesy of JAGUAR CARS, INC.
15. Install the brake pads. Refer to REAR DISC BRAKE (2003.5-09) .

Vehicles with Brembo brakes 

16. Attach the brake caliper.
    • Install new brake caliper retaining bolts.
    • Tighten to 70 Nm.
      Fig 14: Locating Brake Caliper Retaining Bolts

      Courtesy of JAGUAR CARS, INC.

All vehicles 

17. Install the front muffler. Refer to FRONT MUFFLER - 3.0L/3.5L/4.2L (30.10.18) .
18. Install both the upper arms.

    For additional information, refer to

19. Fill the right-hand fuel tank saddle. Refer to FUEL SYSTEM-GENERAL INFORMATION (2003.5-09) .
CAUTION: The final tightening of the rear suspension components must be carried out with the vehicle on its wheels.
Fig 15: Locating Shock Absorber Retaining Bolt
Courtesy of JAGUAR CARS, INC.
20. Tighten to 133 Nm.
21. Check the wheel alignment and adjust as necessary. Refer to GENERAL PROCEDURES .
22. Carry out the rear subframe alignment procedure. Refer to UNI-BODY, SUBFRAME AND MOUNTING SYSTEM (2003.5-09) .