Instrument Cluster
CAUTION:
When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00.
NOTE:
If the control module/component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module/component.
NOTE:
When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places and with a current calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
NOTE:
Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests.
NOTE:
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
NOTE:
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
| DTC | Description | Possible Causes | Action |
|---|---|---|---|
| B1202 | Fuel Sender Circuit Open | Instrument cluster, fuel sender - circuit open | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check rear electronic module, fuel sender circuit for open circuit |
| B1204 | Fuel Sender Circuit Short To Ground | Instrument cluster, fuel sender - short to ground | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check rear electronic module, fuel sender circuit for short to ground |
| B1205 | EIC Switch-1 Assembly Circuit Failure | Instrument cluster, auxiliary lighting switch pack - circuit fault | Refer to electrical circuit diagrams, notes and check instrument cluster, auxiliary lighting switch pack for circuit fault |
| B1209 | EIC Switch-2 Assembly Circuit Failure | Instrument cluster, main lighting switch (column switchgear) - circuit fault | Refer to electrical circuit diagrams, notes and check instrument cluster, main lighting switch pack (column switchgear) for circuit fault |
| B1213 | Anti-Theft Number of Programmed Keys Is Below Minimum | (LED flash 21) Number of programmed keys below minimum (2 keys minimum/8 keys maximum) | Count stored number of transponder keys using the manufacturer approved diagnostic system. Add key's as required |
| B1246 | Dim Panel Potentiometer Switch Circuit Failure | Instrument cluster, auxiliary lighting switch pack (dimmer) - circuit fault | Refer to electrical circuit diagrams, notes and check instrument cluster, auxiliary lighting switch pack and(dimmer) for circuit fault |
| B1317 | Battery Voltage High | Instrument cluster, power supply voltage above high limit Generator voltage is regulated by the engine control module | Refer to electrical circuit diagrams, notes and check instrument cluster, power supply circuit for voltage fault |
| B1318 | Battery Voltage Low | Instrument cluster, power supply voltage below low limit Generator voltage is regulated by the engine control module | Refer to electrical circuit diagrams, notes and check instrument cluster, power supply circuit for voltage fault |
| B1342 | ECU Is Defective | Instrument cluster - memory fault with ROM or EEPROM checksum | Suspect instrument cluster module check and install a new instrument cluster as required, refer to the new module installation note at the top of the DTC Index |
| B1352 | Ignition Key-In Circuit Failure | Instrument cluster, ignition switch, key-in switch - circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, ignition switch, key-in switch for circuit fault |
| B1359 | Ignition Run/Acc Circuit Failure | Instrument cluster - ignition power input voltage low (more than 15 seconds, starter crank timeout) | Refer to electrical circuit diagrams, notes and check instrument cluster, ignition power and ground for circuit fault |
| B1470 | Lamp Headlamp Input Circuit Failure | Instrument cluster - main lighting switch (column switchgear) headlamp - circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, main lighting switch (column switchgear) headlamp switch and circuit for fault |
| B1567 | Lamp Headlamp Highbeam Circuit Failure | Instrument cluster - main lighting switch (column switchgear) highbeam - circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, main lighting switch (column switchgear) highbeam switch and circuit for fault |
| B1600 | PATS Ignition Key Transponder Signal Is Not Received | (LED flash 13) Instrument cluster - no PATS code received from (passive anti-theft system) key transponder (key fault) | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check for transponder key fault |
| B1601 | PATS Received Incorrect Key-Code From Ignition Key Transponder | (LED flash 15) Instrument cluster - not programmed (passive anti-theft system) transponder key in ignition switch | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check transponder key is programmed to vehicle |
| B1602 | PATS Received Invalid Format Of Key-Code From Ignition Key Transponder | (LED flash 14) Instrument cluster - PATS (passive anti-theft system) code received from transceiver module is incomplete | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster communication to PATS transceiver module circuit for fault |
| B1681 | PATS Transceiver Module Signal Is Not Received | (LED flash 11) Instrument cluster - no communication with the PATS (passive anti-theft system) transceiver module | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check PATS transceiver module circuit for fault |
| B1689 | Autolamp Delay Circuit Failure | Instrument cluster, main lighting switch (column switchgear) autolamp delay - circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, main lighting switch (column switchgear) autolamp delay circuit for fault |
| B1875 | Turn Signal/Hazard Switch Signal Circuit Failure | Instrument cluster, turn signal/hazard switch - signal circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, turn signal/hazard switch for signal circuit fault |
| B2103 | Antenna Not Connected | (LED flash 12) PATS (passive anti-theft system) transceiver circuit fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check other modules for related DTCs. Refer to electrical circuit diagrams, notes and check instrument cluster circuit to PATS transceiver for fault |
| B2139 | Data Mismatch (receive data does not match what was expected) | Instrument cluster, security identification mismatch with the rear electronic module REM (challenge-response error) | Check Instrument cluster for security identification mismatch with the rear electronic module REM |
| B2141 | NVM Configuration Failure | (LED flash 22) Instrument cluster, vehicle ID is not stored in cluster | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Enter vehicle id into instrument cluster (Enable PCM ID transfer) using the manufacturer approved diagnostic system |
| B2143 | NVM Memory Failure | Instrument cluster, Internal EEPROM error | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Suspect instrument cluster internal failure. Clear DTC carry out battery reset, if DTC returns suspect instrument cluster internal failure, check and replace as required, refer to the new module installation note at the top of the DTC Index |
| B2162 | Data Mismatch #2 (receive data does not match what was expected) | Electronic steering column lock ID mismatch with instrument cluster stored ID | Enable Electronic steering column lock ID transfer using the manufacturer approved diagnostic system |
| B2329 | Column Reach Feedback Potentiometer Circuit Open | Instrument cluster, steering column movement assembly, telescope position signal circuit fault - open circuit or short to ground | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, steering column movement assembly, telescope position feedback circuit for open circuit or short to ground |
| B2330 | Column Reach Feedback Potentiometer Circuit Short to Power | Instrument cluster, steering column movement assembly, telescope position signal circuit fault - short to power | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, steering column movement assembly, telescope position feedback circuit for short to power |
| B2333 | Column Tilt Feedback Potentiometer Circuit Open | Instrument cluster, steering column movement assembly, tilt position signal circuit fault - open circuit or short to ground | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, steering column movement assembly, tilt position feedback circuit for open circuit or short to ground |
| B2334 | Column Tilt Feedback Potentiometer Circuit Short to Power | Instrument cluster, steering column movement assembly, tilt position signal circuit fault - short to power | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, steering column movement assembly, tilt position feedback circuit for short to power |
| B2351 | Steering Column Switch Circuit Failure | Instrument cluster, column and pedal adjust switches - input voltage out of range | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, column and pedal adjust switchpack and input circuit for fault |
| B2431 | Transponder Programming Failure | Instrument cluster, transponder keyfob PATS code transmit fault | Suspect transponder keyfob PATS code transmit fault. Check and replace keyfob as required |
| B2472 | Fog Lamp Switch Failure | Instrument cluster, auxiliary lighting switchpack, foglamp switch's - input voltage out of range | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check instrument cluster, auxiliary lighting switchpack (foglamp's input) circuit for voltage fault |
| B2477 | Module Configuration Failure | Instrument cluster, vehicle configuration not programmed or configuration write failure | Enter vehicle configuration into instrument cluster using the manufacturer approved diagnostic system |
| B2627 | Fuel Sender Circuit Open #2 | Fuel tank level sender circuit to rear electronic module - circuit open | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check fuel tank level sender circuit to rear electronic module for open circuit |
| B2628 | Fuel Sender Circuit Short To Ground #2 | Fuel tank level sender circuit to rear electronic module - short to ground | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to electrical circuit diagrams, notes and check fuel tank level sender circuit to rear electronic module for short to ground |
| B2879 | Fuel Tank Jet Pump Fault | Fuel pump module, fuel tank jet pump fault Fuel level (check both sides of the saddle tank) |
Refer to electrical circuit diagrams, notes and check fuel level sender's and fuel tank jet pump circuit's for fault |
| B2881 | Column Reach Movement Fault - Primary Axis | Instrument cluster, steering column movement assembly, telescope primary axis position sensor fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check steering column movement (telescope primary axis position sensor) assembly for fault |
| B2882 | Column Reach Movement Fault - Secondary Axis | Instrument cluster, steering column movement assembly, telescope secondary axis position sensor fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check steering column movement (telescope secondary axis position sensor) assembly for fault |
| B2883 | Column Tilt Movement Fault - Primary Axis | Instrument cluster, steering column movement assembly, tilt primary axis position sensor fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check steering column movement (tilt primary axis position sensor) assembly for fault |
| B2884 | Column Tilt Movement Fault - Secondary Axis | Instrument cluster, steering column movement assembly, tilt secondary axis position sensor fault | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check steering column movement (tilt secondary axis position sensor) assembly for fault |
| C1778 | Power Steering Failure | Instrument cluster, incorrect reply from variable assist steering actuator output transistor or NVM checksum error | Suspect instrument cluster electronic failure. Check and install a new instrument cluster as required, refer to the new module installation note at the top of the DTC Index |
| C1922 | VAPS Solenoid Actuator Output Circuit Open | Instrument cluster, variable assist steering actuator output - open circuit | Refer to electrical circuit diagrams, notes and check instrument cluster, variable assist steering actuator circuit for open circuit |
| C1923 | VAPS Solenoid Actuator Output Circuit Short To Power | Instrument cluster, variable assist steering actuator output - short to power | Refer to electrical circuit diagrams, notes and check instrument cluster, variable assist steering actuator circuit for short to power |
| C1924 | VAPS Solenoid Actuator Output Circuit Short To Ground | Instrument cluster, variable assist steering actuator output - short to ground | Refer to electrical circuit diagrams, notes and check instrument cluster, variable assist steering actuator circuit for short to ground |
| C1986 | VAPS Initial Speed Above threshold | Instrument cluster, variable assist steering actuator output - circuit fault | Refer to electrical circuit diagrams, notes and check instrument cluster power circuit and variable assist steering actuator circuit for loose power connection's or short circuit |
| U0128 | Lost Communication With Park Brake Control Module (EPB message missing even though CAN keep awake message was received) | Instrument cluster - electronic parking brake message missing even though (CAN Bus) keep awake message was received | Check electronic parking brake for stored DTCs. Refer to electrical circuit diagrams, notes and check CAN Bus circuit between instrument cluster and electronic parking brake |
| U1147 | SCP (J1850) Invalid or Missing Data for Vehicle Security | Instrument cluster, invalid response from rear electronic module during challenge/response | Check rear electronic module for stored DTCs |
| U1262 | SCP (J1850) Communication Bus Fault | Instrument cluster - No response from rear electronic module during challenge/response | Check rear electronic module for stored DTCs |
| U1751 | Steering Column Lock System Status Message Missing from REM | Instrument cluster - missing (electronic steering column lock) enable status - OFF message from rear electronic module (logged after 2 retries) | Check rear electronic module for stored DTCs |
| U1752 | Steering Column Lock System Status Message Missing from FEM | Instrument cluster - (electronic steering column lock) missing enable status - OFF message from front electronic module (logged after 2 retries) | Check front electronic module for stored DTCs |
| U1900 | CAN Communication Bus Fault (PATS use only - Receive Error) | Instrument cluster - missing messages on CAN bus | Refer to electrical circuit diagrams, notes and check instrument cluster CAN Bus circuit for fault |
| U2150 | SCP (J1850) Invalid Data from REM | Instrument cluster - (electronic steering column lock) missing or incorrect (electronic steering column lock) enable status from rear electronic module | Check rear electronic module for stored DTCs |
| U2152 | SCP (J1850) Invalid Data from FEM | Instrument cluster - (electronic steering column lock) missing or incorrect enable status from front electronic module | Check front electronic module for stored DTCs |
| U2195 | SCP (J1850) Invalid Data from SCLM | Instrument cluster - (electronic steering column lock) missing or incorrect enable status from electronic steering column lock module | Check electronic steering column lock module for stored DTCs |
| U2196 | Invalid Data for Engine RPM | Instrument cluster receive CAN Bus message with default data for >1 Sec | Check dynamic stability control module for stored DTCs |
| U2197 | Invalid data for Vehicle Speed | Instrument cluster receive CAN Bus message with default data for >1 Sec | Check dynamic stability control module for stored DTCs |
| U2199 | Invalid data for Engine Coolant | Instrument cluster received CAN Bus message with default data for >1 Sec | Check engine control module for stored DTCs |
| U2200 | Invalid 'ODO Count' data | Instrument cluster received CAN Bus message with default data for >1 Sec | Check dynamic stability control module for stored DTCs |
| U2510 | CAN - Invalid data for Vehicle Security | (LED flash 23) Instrument cluster, engine control module PATS identification wrong/mismatch with cluster | Enable engine control module PATS identification transfer to instrument cluster using the manufacturer approved diagnostic system |
| U2511 | CAN - Data Mis-Match (Receive data does not match expected) | Instrument cluster - CAN Bus communication failure with engine management control module | Refer to electrical circuit diagrams, notes and check instrument cluster to engine management control module CAN Bus circuit for fault |
| U2515 | Data Missing for Adaptive Cruise Control | Instrument cluster - CAN message missing from adaptive cruise control (only logged when cruise control is enabled) | Check adaptive cruise control module for stored DTCs |
| U2516 | CAN bus Off | Instrument cluster - CAN Bus communication failure | Refer to electrical circuit diagrams, notes and check Instrument cluster CAN Bus circuit for fault |
| U2519 | Data Missing for EPB | Instrument cluster - CAN message missing from electronic parking brake | Check electronic parking brake module for stored DTCs |
| U2521 | Data Missing for Vehicle Speed | Instrument cluster - CAN message missing from dynamic stability control module | Check dynamic stability control module for stored DTCs |
| U2522 | Data Missing for Transmission Gear Selected | Instrument cluster - CAN message missing from transmission control module | Check transmission control module for stored DTCs |
| U2523 | Data Missing for Engine Speed | Instrument cluster - CAN message missing from engine control module | Check engine control module for stored DTCs |
| U2524 | Data Missing for Air Suspension | Instrument cluster - CAN message missing from air suspension control module | Check air suspension control module for stored DTCs |