LEMON Manuals: Even more car manuals for everyone
Home >> Isuzu >> 2007 >> i-290 LS, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 86 (Engine Control System & Fuel System - 3.7L - Diagnosis & Troubleshooting) >> Engine Cranks but Does Not Run >> Description

Engine Cranks but Does Not Run: Description

WARNING: This page is about a different car, the 2007 Isuzu i-370, 2007 GMC Canyon, and 2007 Chevrolet Colorado. However, it is still accessible from the selected car via links, so may be relevant.

The Engine Cranks but Does Not Run diagnostic table is an organized approach to identifying a condition that causes an engine not to start. The Engine Cranks but Does Not Run diagnostic table directs the service technician to the appropriate system diagnosis.

The Engine Cranks but Does Not Run diagnostic table assumes the following:

Engine Cranks but Does Not Run

Step Action Value(s) Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the DTC information.
Does the scan tool display DTCs P0107, P0335, P0340, P0365, P0601, P0602, P0603, P0604, P0606, P0607, P0651, P1621, P1631, P1680, P1681, P1682, or P2610?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle Go to Step 3 
3 Does the scan tool display any vehicle theft deterrent (VTD) DTCs? - Go to Diagnostic Trouble Code (DTC) List - Vehicle Go to Step 4 
4
  1. Turn ON the ignition, with the engine OFF.
  2. Probe both sides of the ETC fuse with a test lamp that is connected to a good ground.
Does the test lamp illuminate on at least one side of the fuse?		 - Go to Step 5  Go to Powertrain Relay Diagnosis 
5 Command the fuel pump ON with a scan tool.
Does the fuel pump turn ON?		 - Go to Step 6  Go to Fuel Pump Electrical Circuit Diagnosis 
6
  1. Turn OFF the ignition.
  2. Remove an ignition coil. Refer to Ignition Coil Replacement .
  3. Install the J 26792  Spark Tester to the coil boot.
  4. Attempt to start the engine.
Does the spark tester spark?		 - Go to Step 7  Go to Electronic Ignition (EI) System Diagnosis 
7
  1. Turn OFF the ignition.
  2. Disconnect the multi-way harness connector of the fuel injectors. Refer to Inline Harness Connector End Views .
  3. Connect a test lamp between the ignition 1 voltage circuit of the fuel injector, fuse side, and a fuel injector control circuit, powertrain control module (PCM) side.
  4. Crank the engine.
Does the test lamp flash when cranking the engine?		 - Go to Step 8  Go to Fuel Injector Circuit Diagnosis 
8
  1. Turn OFF the ignition.
  2. Install the J 34730-1A  Fuel Pressure Gage. See Special Tools . Refer to Fuel Pressure Gage Installation and Removal .
  3. Turn ON the ignition, with the engine OFF.
  4. Command the fuel pump ON with a scan tool.
Is the fuel pressure within the specified range while the fuel pump is operating?		 334-375 kPa
(48-54 psi)		 Go to Step 9  Go to Fuel System Diagnosis 
9 Inspect for the following conditions:
Did you complete the action?		 - Go to Step 10  -
10
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Attempt to start the engine.
Does the engine start and continue to run?		 - Go to Step 11  Go to Step 2 
11
  1. Allow the engine to reach operating temperature.
  2. Observe the DTC information with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals