LEMON Manuals: Even more car manuals for everyone
Home >> Isuzu >> 2007 >> i-290 LS, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 79 (Engine Mechanical - 4.6L - 4 Of 4) >> Off-Vehicle Repair Instructions (3 Of 3) >> Starter Installation

Starter Installation

WARNING: This page is about a different car, the 2007 Cadillac DTS. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Starter & Cables
    GM1564214Courtesy of GENERAL MOTORS CORP.
  1. If installing a NEW starter transfer the cables from the old starter.
  2. Install the positive battery cable to the starter motor stud.
    3. NOTE: Refer to Fastener Notice .
  3. Install the starter motor stud nut (1).

    Tighten:  Tighten the starter motor stud nut (1) to 9.5 N.m (84 lb in).

  4. Install the solenoid wiring harness to the starter solenoid stud.
  5. Install the starter solenoid stud nut (2).

    Tighten:  Tighten the starter solenoid stud nut (2) to 3.4 N.m (30 lb in).

    6. Fig 2: Locating Starter Motor
    GM1564133Courtesy of GENERAL MOTORS CORP.
  6. Place the starter motor in position in the engine valley.
    7. Fig 3: Identifying Starter Motor Bolts
    GM1564132Courtesy of GENERAL MOTORS CORP.
  7. Install the two starter motor bolts.

    Tighten:  Tighten the starter motor bolts to 30 N.m (22 lb ft).

    8. Fig 4: Identifying CMP Sensor O-Ring
    GM1564128Courtesy of GENERAL MOTORS CORP.
  8. Install a NEW O-ring onto the camshaft position (CMP) sensor.
  9. Lubricate the O-ring with clean engine oil.
    10. Fig 5: Identifying CMP Sensor
    GM1564127Courtesy of GENERAL MOTORS CORP.
  10. Install the CMP sensor.
  11. Install the CMP sensor bolt.

    Tighten:  Tighten the CMP sensor bolt to 10 N.m (89 lb in).

    12. Fig 6: View Of CKP Sensor O-Ring
    GM1564126Courtesy of GENERAL MOTORS CORP.
  12. Install a NEW O-ring onto the crankshaft position (CKP) sensor.
  13. Lubricate the O-ring with clean engine oil.
    14. Fig 7: Locating CKP Sensor
    GM1564124Courtesy of GENERAL MOTORS CORP.
  14. Install the CKP sensor.
  15. Install the CKP sensor bolt.

    Tighten:  Tighten the CKP sensor bolt to 10 N.m (89 lb in).

    16. Fig 8: Locating KS Sensors
    GM1564122Courtesy of GENERAL MOTORS CORP.
  16. Install the knock (KS) sensors.

    Tighten:  Tighten the KS sensors to 20 N.m (15 lb ft).

    17. Fig 9: Identifying Crankshaft Position Sensor Wiring Harness
    GM1564121Courtesy of GENERAL MOTORS CORP.
  17. Install the crankshaft position sensor wiring harness into the engine valley.
    18. Fig 10: View Of CKP & KS Sensor Wiring Harness
    GM1564119Courtesy of GENERAL MOTORS CORP.
  18. Connect the crankshaft position sensor wiring harness to the KS sensors (1).
  19. Connect the crankshaft position sensor wiring harness to the CKP sensor (2).
    20. Fig 11: Identifying Crankshaft Position Sensor & Wiring Harness
    GM1564118Courtesy of GENERAL MOTORS CORP.
  20. Connect the crankshaft position sensor wiring harness (1) to the CMP sensor.
  21. Install the jumping ground bracket bolt (2) to the right cylinder head.

    Tighten:  Tighten the jumping ground bracket bolt (2) to 20 N.m (15 lb ft).

scientia non olet · About LEMON Manuals