LEMON Manuals: Even more car manuals for everyone
Home >> Isuzu >> 2007 >> i-290 LS, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 42 (Seat Heating System And Seat Cooling System) >> Diagnostic Information and Procedures >> DTC B1935 or B2180 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2007 Cadillac DTS. However, it is still accessible from the selected car via links, so may be relevant.

B1935 Left Rear Seat Back

  1. Ignition OFF, disconnect the (C1) harness connector at the rear heated seat module.
  2. Test for less than 10.4 ohms of resistance between the seat back supply voltage circuit terminal 3 and the control circuit terminal 1.
    • If greater than 10.4 ohms, test the supply voltage circuit and the control circuit for an open/high resistance. If the circuits test normal, replace the seat back heating element.
  3. Ignition OFF, disconnect the (C2, C4) harness connectors at the rear heated seat module.
  4. Test for 2.0K-300K ohms of resistance between the seat back temperature sensor signal circuit terminal 19 (C4) and the low reference circuit terminal 5 (C2).
    • If greater than 300K ohms, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat back temperature sensor.
    • If less than 2.0K ohms, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat back temperature sensor.
  5. Ignition OFF, connect the (C1, C2, C4) harness connectors at the heated seat module.
  6. Disconnect the harness connector at the seat back heating element/temperature sensor.
  7. Ignition ON, test for less than 5.2 volts between the temperature sensor signal circuit terminal C and ground.
    • If greater than 5.2 volts, test the signal circuit for a short to voltage. If the circuit tests normal, replace the heated seat module.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the heated seat module.
  8. If all circuits test normal, replace the rear heated seat module.

B2180 Right Rear Seat Back

  1. Ignition OFF, disconnect the (C1) harness connector at the rear heated seat module.
  2. Test for less than 10.4 ohms of resistance between the seat back supply voltage circuit terminal 6 and the control circuit terminal 4.
    • If greater than 10.4 ohms, test the supply voltage circuit and the control circuit for an open/high resistance. If the circuits test normal, replace the seat back heating element.
  3. Ignition OFF, disconnect the (C2, C4) harness connector at the rear heated seat module.
  4. Test for 2.0K-300K ohms of resistance between the seat back temperature sensor signal circuit terminal 10 (C4) and the low reference circuit terminal 7 (C2).
    • If greater than 300K ohms, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat back temperature sensor.
    • If less than 2.0K ohms, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat back temperature sensor.
  5. Ignition OFF, connect the (C1, C2, C4) harness connectors at the heated seat module.
  6. Disconnect the harness connector at the seat back heating element/temperature sensor.
  7. Ignition ON, test for less than 5.2 volts between the temperature sensor signal circuit terminal C and ground.
    • If greater than 5.2 volts, test the signal circuit for a short to voltage. If the circuit tests normal, replace the heated seat module.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the heated seat module.
  8. If all circuits test normal, replace the rear heated seat module.
scientia non olet · About LEMON Manuals