Reference Value
CONSULT DATA MONITOR STANDARD VALUE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor item | Condition | Reference valve in normal operation |
|---|---|---|
| FR LH SENSOR | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| FR RH SENSOR | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| RR LH SENSOR | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| RR RH SENSOR | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| ACCEL POS SIG | Never depress accelerator pedal(Ignition switch ON) | 0% |
| Depress accelerator pedal(Ignition switch ON) | 0 - 100% | |
| SIDE G-SENSOR | Vehicle stopped | Approx. 0 m/s2 |
| Turning right | Negative value | |
| Turning left | Positive value | |
| BATTERY VOLT | Ignition switch ON | 10 - 16 V |
| DECEL G-SEN | When stopped | Approx. 0 G |
| During acceleration | Positive value | |
| During deceleration | Negative value | |
| ENGINE SPEED | Engine stopped | 0 tr/min |
| Engine running | Almost same reading as tachometer | |
| STR ANGLE SIG | When driving straight | ±2.5° |
| When steering wheel is steered to RH by 90° | Approx. +90° | |
| When steering wheel is steered to LH by 90° | Approx. '90° | |
| PRESS SENSOR | Brake pedal not depressed | Approx. 0 bar |
| Brake pedal depressed | 0 - 255 barPressure increases according to pedal effort. | |
| VSO | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| FR WHEEL SPD | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| FL WHEEL SPD | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| RR WHEEL SPD | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| RL WHEEL SPD | Vehicle stopped | 0.00 km/h (MPH) |
| When driving*1 | Nearly matches the speedometer display (within ±10%) | |
| YAW RATE SEN | Vehicle stopped | Approx. 0 d/s |
| Turning right | Negative value | |
| Turning left | Positive value | |
| FR RH IN SOL*2 | When front RH ABS IN valve is active | On |
| When front RH ABS IN valve is not activated | Off | |
| FR RH OUT SOL*2 | When front RH ABS OUT valve is active | On |
| When front RH ABS OUT valve is not activated | Off | |
| FR LH IN SOL*2 | When front LH ABS IN valve is active | On |
| When front LH ABS IN valve is not activated | Off | |
| FR LH OUT SOL*2 | When front LH ABS OUT valve is active | On |
| When front LH ABS OUT valve is not activated | Off | |
| RR RH IN SOL*2 | When rear RH ABS IN valve is active | On |
| When rear RH ABS IN valve is not activated | Off | |
| RR RH OUT SOL*2 | When rear RH ABS OUT valve is active | On |
| When rear RH ABS OUT valve is not activated | Off | |
| RR LH IN SOL*2 | When rear LH ABS IN valve is active | On |
| When rear LH ABS IN valve is not activated | Off | |
| RR LH OUT SOL*2 | When rear LH ABS OUT valve is active | On |
| When rear LH ABS OUT valve is not activated | Off | |
| EBD WARN LAMP | Brake warning lamp is ON*3 | On |
| Brake warning lamp is OFF*3 | Off | |
| STOP LAMP SW | Brake pedal is pressed | On |
| Brake pedal is released | Off | |
| ABS WARN LAMP | ABS warning lamp is ON*3 | On |
| ABS warning lamp is OFF*3 | Off | |
| MOTOR RELAY | When ABS motor and motor relay are active | On |
| When ABS motor and motor relay are not activated | Off | |
| ACTUATOR RLY*2 | When ABS actuator relay is active | On |
| When ABS actuator relay is not activated (in fail-safe mode) | Off | |
| OFF LAMP | VDC OFF indicator lamp is ON*3 | On |
| VDC OFF indicator lamp is OFF*3 | Off | |
| OFF SW | VDC OFF display selection is ON | On |
| VDC OFF display selection is OFF | Off | |
| SLIP/VDC LAMP | VDC warning lamp is ON*3 | On |
| VDC warning lamp is OFF*3 | Off | |
| TRQ DOWN SIG | When Engine TCS is active | On |
| When Engine TCS is not active | Off | |
| EBD SIGNAL | When EBD function is active | On |
| When EBD function is not activated | Off | |
| ABS SIGNAL | When ABS function is active | On |
| When ABS function is not activated | Off | |
| TCS SIGNAL | When TCS function is active | On |
| When TCS function is not activated | Off | |
| VDC SIGNAL | When VDC function is active | On |
| When VDC function is not activated | Off | |
| EBD FAIL SIG | When EBD function is fail-safe | On |
| When EBD function is normal | Off | |
| ABS FAIL SIG | When ABS function is fail-safe | On |
| When ABS function is normal | Off | |
| TCS FAIL SIG | When TCS function is fail-safe | On |
| When TCS function is normal | Off | |
| VDC FAIL SIG | When VDC function is fail-safe | On |
| When VDC function is normal | Off | |
| GEAR | Driving | 1-7Depending on status |
| NEXT GEAR POSI | Driving | CVT in continuous mode |
| N POSI SIG | When selector is in the N position | On |
| When selector is in the other position than N | Off | |
| P POSI SIG | When selector is in the P position | On |
| When selector is in the other position than P | Off | |
| R POSI SIG | When selector is in the R position | On |
| When selector is in the other position than R | Off | |
| DECEL G-SEN1 | When G sensor1 is active | On |
| When G sensor1 is not active | Off | |
| DECEL G-SEN2 | When G sensor2 is active | On |
| When G sensor2 is not active | Off | |
| CRANKING SIG | When cranking | On |
| When other than cranking | Off | |
| FLUID LEV SW | When brake fluid level switch is ON (brake fluid level is less than the specified level) | On |
| When brake fluid level switch is OFF | Off | |
| PARK BRAKE SW | When parking brake is active | On |
| When parking brake is released | Off | |
| 4WD MODE MON | Always | AUTO, LOCK, 2WD(Depending on AWD control status) |
| 4WD FAIL | When AWD controller is in fail-safe mode | On |
| When AWD controller is normal | Off | |
| CV1 | When cut valve 1 is active | On |
| When cut valve 1 is not activated | Off | |
| CV2 | When cut valve 2 is active | On |
| When cut valve 2 is not activated | Off | |
| SV1 | When suction valve 1 is active | On |
| When suction valve is not activated | Off | |
| SV2 | When suction valve 2 is active | On |
| When suction valve is not activated | Off | |
| RELEASE SW NC | Active booster signal status | On |
| Off | ||
| OBH FAIL | When HBB/HBC is in fail-safe mode | On |
| When HBB/HBC is normal | Off | |
| HBA FAIL | When HBA is in fail-safe mode | On |
| When HBA is normal | Off | |
| OBH SIG | When HBB/HBC is active | On |
| When HBB/HBC is not active | Off | |
| HBA SIG | When HBA is active | On |
| When HBA is not active | Off | |
| USS SIG*4 | When hill start assist function is active | On |
| When hill start assist function is not activated | Off | |
| Wheel speed repro impossible | When vehicle speed is greater than 0.00 km/h (MPH) | On |
| When vehicle speed is 0.00 km/h (MPH) | Off | |
| Low voltage repro impossible | When voltage is lower than 12V | On |
| When voltage is higher than 12V | Off |
*1: Confirm tire pressure is standard value. *2: Display occasionally changes On/Off for a moment after ignition switch is placed ON. This is operation for checking purposes and is not a malfunction. *3: Refer to Warning Lamp/Indicator Lamp for ON/OFF conditions of each warning lamp and indicator lamp. *4: "USS" means "hill start assist" or "Uphill Start Support".