Data Monitor
WARNING: This page is about a different car, the 2016 Infiniti Q50. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitored item | Unit | Description |
|---|---|---|
| BATT ELECTRIC CURRENT | A | Displays the current value detected by the current sensor. |
| INPUT POSSIBLE POWER | kW | Displays the power which can be input to the Li-ion battery. |
| OUTPUT POSSIBLE POWER | kW | Displays the power which can be output from the Li-ion battery. |
| 12V BATTERY VOLTAGE | mV | Displays the 12V power voltage. |
| IR SEN SHORT PULSE | mV | Displays the difference between the maximum voltage and minimum voltage in the voltage amplitude for insulation resistance drop detection. |
| SOC | % | Displays the charge status of the Li-ion battery. |
| SERVICE PLUG INTERLOCK | OPEN/CLOSE | Displays the service plug connected/disconnected status. |
| CELL VOLTAGE 01 - 96 | mV | Displays the voltage of each cell. |
| TOTAL BATTERY VOLTAGE | V | Displays the total voltage of the Li-ion battery. |
| MAXIMUM CELL VOLTAGE | mV | Displays the current highest cell voltage. |
| MINIMUM CELL VOLTAGE | mV | Displays the current lowest cell voltage. |
| FAIL STATUS | NO ACT/RLY Off | Displays the vehicle fail-safe status. |
| LBC MODE STATUS | NORMAL/TRQ Off/BALESS/BLANK | Displays the fail-safe status of the Li-ion battery controller (LBC). |
| BATTERY TEMPERATURE 1 | deg | Displays the temperature calculated using the signal voltage from battery temperature sensor 1 (Module 4). |
| BATTERY TEMPERATURE 2 | deg | Displays the temperature calculated using the signal voltage from battery temperature sensor 2 (Module 12). |
| BATTERY TEMPERATURE 3 | deg | Displays the temperature calculated using the signal voltage from the battery temperature sensor 3 (Intake air). |
| AD VALUE OF AVCC VOLTAGE | mV | Displays the analog power voltage. |
| MIL ON REQ | YES/NO | Displays the status of malfunctioning indicator lamp signal from the Li-ion battery controller (LBC). |
| THERMO SENSOR 1 AD VALUE | mV | Displays a signal voltage from Battery temperature sensor 1. |
| THERMO SENSOR 2 AD VALUE | mV | Displays a signal voltage from Battery temperature sensor 2. |
| THERMO SENSOR 3 AD VALUE | mV | Displays a signal voltage from Battery temperature sensor 3. |
| A/D OFFSET CORRECT | mV | Displays a corrected output voltage value of Current sensor. |
| CUR SEN OFFSET VALUE | mV | Displays a corrected voltage value of Current sensor. |
| AVERAGE BATT TEMP | deg | Displays current average battery temperature. |
| SUM OF ALL CELL VOLTAGE | V | Displays sum of all cell voltage values. |
| TOTAL VOLTAGE A/D VALUE | mV | Displays voltage values of all voltage sensors. |
| CURRENT SEN A/D VALUE | mV | Displays out voltage value of current sensor. |
| IR MONITOR A/D SAMP VALUE | mV | Displays voltage value of low insulation resistance detection sensor. |
| MIN BATT TEMPERATURE | deg | Displays the present lowest battery temperature. |
| FAN OUTPUT DUTY | % | Displays a drive duty value of battery cooling fan. |
| FAN DUTY MEASURE VALUE | % | Displays a rotating duty value of battery cooling fan. |
| DC/DC FAN STATUS | LOW/MID/HIGH/HIGH+LMT | Displays the status of DC/DC converter cooling request. |
| STATUS OF DC/DC 1 | Hz | Displays a DC/DC converter monitor signal frequency. |
| FAN MONITOR SIGNAL | Hz | Displays a battery cooling fan rotation signal frequency. |
| FAN FREQUENCY | Hz | Displays a 100ms average value of battery cooling fan rotation signal frequency. |
| DC/DC FREQUENCY | Hz | Displays a 100ms average value of DC/DC converter monitor signal frequency. |