Physical Values
| Terminal No. (Wire Color) |
Description | Condition | Value (Approx.) |
|||
|---|---|---|---|---|---|---|
| + | - | Signal Name | Input/ Output |
|||
| 1 (BG) |
Ground | Battery power supply | Input | Ignition Switch OFF | Battery voltage | |
| 2 (LG) |
Ground | Communication signal (METER→ AMP.) | Output | Ignition Switch ON | ||
| 3 (GR) |
Ground | Communication signal (AMP.→ METER) | Input | Ignition Switch ON |
|
|
| 5 (B) |
Ground | Ground | - | Ignition Switch ON | 0 V | |
| 6 (W) |
Ground | Alternator signal | Input | Ignition Switch ON | Charge Warning Lamp ON | 0 V |
| Charge Warning Lamp OFF | Battery voltage | |||||
| 7 (P) |
Ground | Air bag signal | Input | Ignition Switch ON | Air bag Warning Lamp ON | 4 V |
| Air bag Warning Lamp OFF | 0 V | |||||
| 10 (G) |
Ground | Security indicator signal | Input | Ignition Switch OFF | Security Warning Lamp ON | 0 V |
| Security Warning Lamp OFF | 12 V | |||||
| 15 (B) |
Ground | Ground | - | Ignition Switch ON | 0 V | |
| 16 (B) |
Ground | Meter Control Switch ground | - | Ignition Switch ON | 0 V | |
| 21 (R) |
Ground | Ignition signal | Input | Ignition Switch ON | Battery voltage | |
| 24 (BR) |
Ground | Communication signal (LCD→ AMP.) | Output | Ignition Switch ON | ||
| 25 (Y) |
Ground | Communication signal (AMP.→ LCD) | Input | Ignition Switch ON | ||
| 26 (R) |
Ground | Vehicle speed signal (8 - pulse) |
Input | Ignition Switch ON | Speedometer operated [When vehicle speed is approx. 40 km/h (25 MPH)] |
NOTE:
The maximum voltage varies depending on the specification (destination unit). |
| 27 (V) |
Ground | Parking Brake Switch signal | Input | Ignition Switch ON | Parking brake ON | 0 V |
| Parking brake OFF | ||||||
| 28 (W) |
Ground | Brake Fluid Level Switch Signal | Input | Ignition Switch ON | Brake fluid level is normal. | 5 V |
| The brake fluid level is lower than the low level | 0 V | |||||
| 29 (SB) |
Ground | Seat Belt Buckle Switch Signal (Driver Side) | Input | Ignition Switch ON | When driver seat belt is fastened | 12 V |
| When driver seat belt is unfastened | 0 V | |||||
| 30 (G) |
Ground | Passenger seat belt warning signal | Input | Ignition Switch ON |
|
12 V |
|
0 V | |||||
| 31 (L) |
Ground | Washer Level Switch signal | Input | Ignition Switch ON | Washer Level Switch ON | 0 V |
| Washer Level Switch OFF | 5 V | |||||
| 34 (B) |
Ground | Illumination control signal | Output | Ignition Switch ON | Lighting switch ON, then operate the illumination control switch. |
NOTE:
When brightness level is midway |
| 36 (LG) |
16 (B) |
Select switch signal | Input | Ignition Switch ON | When |
0 V |
| Other than the above | 5 V | |||||
| 37 (SB) |
16 (B) |
Enter switch signal | Input | Ignition Switch ON | When |
0 V |
| Other than the above | 5 V | |||||
| 38 (L) |
16 (B) |
Trip A/B Reset Switch signal | Input | Ignition Switch ON | When trip A/B reset switch is pressed | 0 V |
| Other than the above | 5 V | |||||
| 39 (P) |
16 (B) |
Illumination control switch signal (-) | Input | Ignition Switch ON | When |
0 V |
| Other than the above | 5 V | |||||
| 40 (BG) |
16 (B) |
Illumination control switch signal (+) | Input | Ignition Switch ON | When |
0 V |
| Other than the above | 5 V | |||||