LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2016 >> Q50 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 169 (Automatic Transmission (Symptom Diagnosis & Removal And Installation) (Except Hybrid)) >> Unit Disassembly And Assembly >> Oil Pump, 2346 Brake, Front Brake Piston >> Assembly

Oil Pump, 2346 Brake, Front Brake Piston: Assembly

WARNING: This page is about a different car, the 2018 Infiniti Q50. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install O-ring SYMBOL to oil pump cover.
    GNSJPDIA1102Z-102Courtesy of NISSAN NORTH AMERICA, INC.
  2. Install O-ring to oil pump housing.
    G04075849Courtesy of NISSAN NORTH AMERICA, INC.
  3. Using the drift, install oil pump housing oil seal to the oil pump housing until it is flush.
    G04075853Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • Never reuse oil seal.
    • Apply ATF to oil seal.
  4. Install oil pump housing to oil pump cover and tighten bolts (SYMBOL ) to the specified torque in numerical order shown in the figure after temporarily tightening them.
    GNSJPDIA1101Z-101Courtesy of NISSAN NORTH AMERICA, INC.
  5. Install D-ring (large) SYMBOL and D-ring (small) SYMBOL to 2346 brake piston.
    GNSJPDIA1100Z-100Courtesy of NISSAN NORTH AMERICA, INC.
  6. Install 2346 brake piston SYMBOL to oil pump assembly.
    GNSJSDIA1722Z-722Courtesy of NISSAN NORTH AMERICA, INC.
  7. Install D-ring (inner) SYMBOL and D-ring (outer) SYMBOL to front brake piston.
    GNSJPDIA1098Z-098Courtesy of NISSAN NORTH AMERICA, INC.
  8. Install front brake piston SYMBOL to oil pump assembly.
    GNSJSDIA1723Z-723Courtesy of NISSAN NORTH AMERICA, INC.
  9. Install 2346 brake spring retainer SYMBOL to oil pump assembly.
    GNSJPDIA1096Z-096Courtesy of NISSAN NORTH AMERICA, INC.
  10. Set the clutch spring compressor [SST: KV31102400 (J-34285 and J-34285-87)] (A) on 2346 brake spring retainer and install snap ring (fixing 2346 brake spring retainer) SYMBOL to oil pump assembly while compressing return spring.
    GNSJSDIA1730Z-730Courtesy of NISSAN NORTH AMERICA, INC.

    (B)

    : Press
    CAUTION: Be careful not to expand snap ring excessively.
  11. Install front brake spring retainer SYMBOL to oil pump assembly.
    GNSJPDIA1094Z-094Courtesy of NISSAN NORTH AMERICA, INC.
  12. Set the clutch spring compressor (SST: KV31103800) (A) on front brake spring retainer and install snap ring (fixing front brake spring retainer) SYMBOL to oil pump assembly while compressing return spring.
    GNSJSDIA1729Z-729Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION: Be careful not to expand snap ring excessively.
  13. Install seal ring SYMBOL to oil pump assembly.
    GNSJPDIA1092Z-092Courtesy of NISSAN NORTH AMERICA, INC.
  14. Install 2346 brake component part (retaining plate, drive plates, driven plates, dish plate and snap ring) to oil pump assembly.
    GNSJPDIA1152Z-152Courtesy of NISSAN NORTH AMERICA, INC.

    SYMBOL

    : Dish plate

    SYMBOL

    : Driven plate (four pieces)

    SYMBOL

    : Drive plate (four pieces)

    SYMBOL

    : Retaining plate

    SYMBOL

    : Snap ring
    CAUTION:
    • Check the order of plates.
    • Never install snap ring mating part (A) to the clearance groove [(B) shown in the figure] of oil pump cover.
      GNSJSDIA1724Z-724Courtesy of NISSAN NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals