LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2015 >> QX60 Base, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 40 (Engine Control System (DTC/Circuit Diagnosis) (VQ35DE) (Except Hybrid) (1 Of 3)) >> DTC/Circuit Diagnosis >> DTC P0101: MAF Sensor >> Diagnosis Procedure >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2016 Infiniti QX60. However, it is still accessible from the selected car via links, so may be relevant.

  1. CHECK INTAKE SYSTEM

    Check the following for connection.

    • Air duct
    • Vacuum hoses
    • Intake air passage between air duct and intake manifold

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Reconnect the parts.

  2. CHECK MASS AIR FLOW (MAF) SENSOR POWER SUPPLY

    1. Disconnect MAF sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between MAF sensor harness connector and ground.
      + - Voltage
      MAF sensor
      Connector Terminal
      F74 1 Ground Approx. 5 V

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    GO TO STEP 3  .

  3. CHECK MASS AIR FLOW (MAF) SENSOR POWER SUPPLY CIRCUIT

    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between MAF sensor harness connector and ECM harness connector.
      MAF sensor ECM Continuity
      Connector Terminal Connector Terminal
      F74 1 F78 28 Existed

    Is the inspection result normal?

    YES 

    Check intermittent incident. Refer to INTERMITTENT INCIDENT .

    NO 

    Repair or replace error-detected parts.

  4. CHECK MAF SENSOR GROUND CIRCUIT

    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between MAF sensor harness connector and ECM harness connector.
      MAF sensor ECM Continuity
      Connector Terminal Connector Terminal
      F74 2 F78 40 Existed
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES 

    GO TO STEP 5  .

    NO 

    Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK MAF SENSOR INPUT SIGNAL CIRCUIT

    1. Check the continuity between MAF sensor harness connector and ECM harness connector.
      MAF sensor ECM Continuity
      Connector Terminal Connector Terminal
      F74 3 F78 38 Existed
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    Repair open circuit or short to ground or short to power in harness or connectors.

  6. CHECK INTAKE AIR TEMPERATURE SENSOR

    Check intake air temperature sensor. Refer to COMPONENT INSPECTION .

    Is the inspection result normal?

    YES 

    GO TO STEP 7  .

    NO 

    Replace MAF sensor (with intake air temperature sensor).

  7. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR

    Check EVAP control system pressure sensor. Refer to COMPONENT INSPECTION .

    Is the inspection result normal?

    YES 

    GO TO STEP 8  .

    NO 

    Replace EVAP control system pressure sensor.

  8. CHECK MAF SENSOR

    Check MAF sensor. Refer to COMPONENT INSPECTION .

    Is the inspection result normal?

    YES 

    Check intermittent incident. Refer to INTERMITTENT INCIDENT .

    NO 

    Replace MAF sensor. Refer to REMOVAL AND INSTALLATION .

scientia non olet · About LEMON Manuals