Error History

WARNING: This page is about a different car, the 2016 Infiniti QX60. However, it is still accessible from the selected car via links, so may be relevant.

The self diagnosis results are judged depending on whether any error occurs from when Self diagnosis is selected until the self diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned ON and then no error has occurred until the self

diagnosis start. Check the Error Record to detect any error that may have occurred before the self diagnosis start because of this situation.

The frequency of occurrence is displayed in a count up manner. The actual count up method differs depending on the error item.

Count up method A

The counter resets to 0 if an error occurs when ignition switch is turned ON. The counter increases by 1 if the condition is normal at a next ignition ON cycle.
The counter upper limit is 39. Any counts exceeding 39 are ignored." The counter can be reset (no error record display) with the "Delete log" switch or CONSULT.

Count up method B

The counter increases by 1 if an error occurs when ignition switch is ON. The counter will not decrease even if the condition is normal at the next ignition ON cycle.
The counter upper limit is 50. Any counts exceeding 50 are ignored. " The counter can be reset (no error record display) with the "Delete log" switch or CONSULT.

Display type of occurrence frequency	Error history display item
Count up method A	CAN communication line, control unit (CAN), AV communication line, control unit (AV)
Count up method B	Other than the above

Courtesy of NISSAN NORTH AMERICA, INC.

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

Error item	Description	Possible cause
CAN COMM CIRCUIT	CAN communication malfunction is detected.	Perform diagnosis with CONSULT, then repair the malfunctioning components according to diagnosis results. Refer to CONSULT FUNCTION
CONTROL UNIT (CAN)	CAN initial diagnosis malfunction is detected.	Replace the AV control unit if the malfunction occurs constantly. Refer to REMOVAL AND INSTALLATION .
CONTROL UNIT (AV)	AV communication circuit initial diagnosis malfunction is detected.
FLASH - ROM Error Of Control Unit	AV control unit malfunction is detected.
CAN Controller Memory Error	AV control unit malfunction is detected.
Steer. Angle Sensor Calibration	Predictive course line center position adjustment of the steering angle sensor is incomplete.	Adjust the predictive course line center position of the steering angle sensor. Refer to CONSULT FUNCTION .
Display Connection Error	When any of the following is detected: display unit power supply or ground circuits malfunction. communication circuit malfunction between AV control unit and display unit.	Display unit power supply or ground circuits. Refer to DIAGNOSIS PROCEDURE . Communication circuits between AV control unit and display unit. Refer to DTC LOGIC .
XM Connection Error	When any of the following is detected: satellite radio tuner power supply or ground circuit malfunction. communication circuit malfunction between AV control unit and satellite radio tuner. request signal circuit malfunction between AV control unit and satellite radio tuner.	Satellite radio tuner power supply or ground circuits. Refer to DIAGNOSIS PROCEDURE . Communication circuit between AV control unit and satellite radio tuner. Refer to DTC LOGIC . Request signal circuit between AV control unit and satellite radio tuner. Refer to DTC LOGIC .
AV COMM CIRCUIT Switches Connection Error	When any of the following is detected: Multifunction switch power supply or ground circuit malfunction. AV communication circuit malfunction between AV control unit and multifunction switch.	Multifunction switch power supply or ground circuits. Refer to DIAGNOSIS PROCEDURE . AV communication circuits between AV control unit and multifunction switch.
AV COMM CIRCUIT BTHF Unit Connection Error	When any of the following is detected: Bluetooth^® control unit power supply or ground circuit malfunction. AV communication circuit malfunction between AV control unit and Bluetooth^® control unit.	Bluetooth^® control unit power supply or ground circuits. Refer to DIAGNOSIS PROCEDURE . AV communication circuits between AV control unit and Bluetooth^® control unit.
AV COMM CIRCUIT Switches Connection Error BTHF Unit Connection Error	AV communication circuit malfunction between AV control unit and multifunction switch.	AV communication circuits between AV control unit and multifunction switch.