Diagnosis Procedure

Regarding Wiring Diagram information, refer to "WIRING DIAGRAM ".

1. CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION 
   1. Perform initialization setting of automatic back door position information.

      Refer to "WORK PROCEDURE ".

   2. Erase DTC, and then repeat "PERFORM DTC CONFIRMATION PROCEDURE".

      Is DTC detected? 

      YES: GO TO 2.

      NO: Inspection End.

2. CHECK INSTALLATION OF BACK DOOR ASSEMBLY 
   1. Check that back door assembly is installed normally.

      Refer to "BACK DOOR ASSEMBLY: ADJUSTMENT ".

   2. Check back door assembly mechanism deformation, looseness, rattle, interference with other parts and pinched foreign materials.

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Repair or replace the malfunctioning parts.

3. CHECK ENCODER SIGNAL 
   1. Select "AUTOMATIC BACK DOOR CONTROL MODULE" using CONSULT.
   2. Select "SPINDLE SENSOR LH" and "SPINDLE SENSOR RH" in "DATA MONITOR" mode.
   3. Check that the function operates normally according to the following conditions.

      Monitor item	Status
      SPINDLE SENSOR LH	0 - 65535
      SPINDLE SENSOR RH	0 - 65535

      Is the difference between the 2 monitor items 10 or more? 

      YES: GO TO 4.

      NO: Replace automatic back door control module. Refer to "REMOVAL AND INSTALLATION ".

4. CHECK ENCODER POWER SUPPLY 
   1. Turn ignition switch OFF.
   2. Disconnect spindle unit connector.
   3. Check voltage between spindle unit harness connector and ground.

      (+)			(-)	Voltage (Approx.)
      Spindle unit
      Connector		Terminal
      LH	B70	8	Ground	16.75 - 6 V
      RH	B162

      Is the inspection result normal? 

      YES: GO TO  6.

      NO: GO TO 5.

5. CHECK ENCODER CIRCUIT 
   1. Disconnect automatic back door control module connector.
   2. Check continuity between automatic back door control module harness connector and spindle unit harness connector.

      Automatic back door control module		Spindle unit			Continuity
      Connector	Terminal	Connector		Terminal
      B55	19	LH	B70	8	Yes
      	20	RH	B162

   3. Check continuity between automatic back door control module harness connector and ground.

      Automatic back door control module		Ground	Continuity
      Connector	Terminal
      B55	19		No
      	20

      Is the inspection result normal? 

      YES: Replace automatic back door control module. Refer to "REMOVAL AND INSTALLATION ".

      NO: Repair or replace harness.

6. CHECK ENCODER CIRCUIT 2 
   1. Disconnect automatic back door control module connector.
   2. Check continuity between automatic back door control module harness connector and spindle unit harness connector.

      Automatic back door control module		Spindle unit			Continuity
      Connector	Terminal	Connector		Terminal
      B55	6	LH	B70	3	Yes
      	7			10
      	8	RH	B162	3
      	9			10

   3. Check continuity between automatic back door control module harness connector and ground.

      Automatic back door control module		Ground	Continuity
      Connector	Terminal
      B55	6		No
      	7
      	8
      	9

      Is the inspection result normal? 

      YES: GO TO 7.

      NO: Repair or replace harness.

7. CHECK ENCODER CIRCUIT 3 
   1. Connect automatic back door control module and spindle unit connector
   2. Check continuity between automatic back door control module harness connector and ground.

      Automatic back door control module		Ground	Voltage (Approx.)
      Connector	Terminal
      B55	21		0 V

      Is the inspection result normal? 

      YES: GO TO 8.

      NO: Replace automatic back door control module. Refer to "REMOVAL AND INSTALLATION ".

8. CHECK INTERMITTENT INCIDENT 

   Refer to "INTERMITTENT INCIDENT ".

   Is the inspection result normal? 

   YES: Replace automatic back door control module. Refer to "REMOVAL AND INSTALLATION ".

   NO: Repair or replace the malfunctioning parts.