Physical Values
WARNING: This page is about a different variant/trim than selected.
TERMINALS REFERENCE
| Terminal No. (Wire color) |
Description | Condition | Value (Approx.) | |||
|---|---|---|---|---|---|---|
| + | - | Signal name | Input/Output | |||
| 6 (BR) | Ground | Hi-Lo position sensor 1 | Input/Output | Engine running (Never drive the vehicle.) | 4WD mode: AUTO or 4H | 0 V |
| 4WD mode: Shifting | 0 V | |||||
| 4WD mode: 4L | 5 V | |||||
| 7 (Y) | Ground | Transfer fluid temperature sensor power supply | Input | Engine running | 0 - 5V | |
| 9 (G) | Ground | Transfer internal speed sensor (GND) | - | Always | 0 V | |
| 10 (Y/G) | Ground | Transfer internal speed sensor (IMP) | Input | IGN ON | Transfer motor driving | |
| 11 (V) | Ground | 4WD shift SW (4Lo) | Input | IGN ON | 4WD shift switch: 4L | Battery voltage |
| 4WD shift switch: Except 4L | 0 V | |||||
| 12 (L) | - | CAN-H | Input/Output | - | - | |
| 13 (P) | - | CAN-L | Input/Output | - | - | |
| 14 (W/R) | Ground | 4WD shift SW (AUTO) | Input | IGN ON | 4WD shift switch: AUTO | Battery voltage |
| 4WD shift switch: Except AUTO | 0 V | |||||
| 15 (P/B) | Ground | Transfer rotary position sensor (PWM) | Input | IGN ON | ||
| 16 (LG) | Ground | Transfer rotary position sensor (GND) | - | Always | 0 V | |
| 17 (W/L) | Ground | Transfer lock position sensor power supply | Input | IGN ON | 5V | |
| 10 seconds or more later after ignition switch turned OFF | 0V | |||||
| 18 (BR/Y) | Ground | Transfer rotary position sensor power supply | Input | IGN ON | 5V | |
| 10 seconds or more later after ignition switch turned OFF | 0V | |||||
| 20 (GR) | Ground | Transfer control unit power supply | Input | Always | Battery voltage | |
| 25 (P/L) | Ground | Hi-Lo position sensor 3 | Input/Output | Engine running (Never drive the vehicle.) | 4WD mode: AUTO or 4H | 0 V |
| 4WD mode: Shifting | 5 V | |||||
| 4WD mode: 4L | 5 V | |||||
| 28 (W) | Ground | Transfer motor temperature sensor power supply | Input | IGN ON | 0 - 5V | |
| IGN OFF | 0V | |||||
| 29 (LG/R) | Ground | Hi-Lo position sensor 2 | Input/Output | Engine running (Never drive the vehicle.) | Always | 0 V |
| 30 (R/B) | Ground | Transfer lock position sensor (GND) | - | Always | 0 V | |
| 31 (L/O) | Ground | Transfer internal speed sensor (DIR) | Input | IGN ON | When changing the transfer motor rotation direction. | |
| 32 (BR/R) | Ground | IGN SW | Input | IGN ON | Battery voltage | |
| IGN OFF | 0V | |||||
| 35 (R) | Ground | 4WD shift SW (4H) | Input | IGN ON | 4WD shift switch: 4H | Battery voltage |
| 4WD shift switch: Except 4H | 0 V | |||||
| 36 (L/R) | Ground | Transfer fluid temperature sensor (GND) | - | Always | 0 V | |
| 38 (G/O) | Ground | Transfer lock position sensor signal | Input | IGN ON | ||
| 39 (R/W) | Ground | Transfer internal speed sensor power supply | Input | IGN ON | 8 V | |
| IGN OFF | 0V | |||||
| 41 (W/R) | Ground | Transfer control actuator power supply | Input | Always | Battery voltage | |
| 43 (G/R) | Ground | Motor drive B | Input/Output | Transfer motor driving | 0V - Battery voltage | |
| 44 (B) | Ground | GND | - | Always | 0 V | |
| 45 (G/Y) | Ground | Motor drive A | Input/Output | Transfer motor driving | 0V - Battery voltage | |
| 46 (B) | Ground | Transfer control actuator (GND) | - | Always | 0 V | |
CAUTION:
When using circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.