LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2008 >> M35 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel >> Instrument Panel Assembly >> INSTRUMENT PANEL : Removal and Installation >> Removal

INSTRUMENT PANEL : Removal and Installation: Removal

  1. Remove cup holder.
    • Pull up to remove cup holder.
      Fig 1: Removing Cup Holder
      G05212839Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Remove switch finisher.
    • Remove switch finisher fixing screws.
    • Disconnect harness connector.
  3. Remove A/T console finisher.
    • Place the selector lever in "D" position.
    • Remove selector lever knob. Refer to "CONTROL DEVICE REMOVAL AND INSTALLATION ".
    • Lift up backside and pull back.
    • Disconnect harness connector.
      Fig 2: Removing A/T Console Finisher
      G05212840Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Remove cluster lid C.
    Fig 3: Removing Cluster Lid C
    G05212841Courtesy of NISSAN MOTOR CO., U.S.A.
    • Remove cluster lid C fixing screws.
    • Pull back.
    • Disconnect harness connector.
  5. Remove console rear finisher.
    • Insert a remover into upper space of console rear finisher.
    • Pull back console rear finisher.
      • Fig 4: Removing Console Rear Finisher
      G05212842Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Remove center console fixing screws with power tool.
    • Pull up center console.
    • Disconnect harness connector.
  7. Remove glove box.
    • Remove damper pin to left side.
    • Pull up glove box.
      • Fig 5: Removing Center Console With Power Tool
      G05212843Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Remove instrument passenger lower cover.
    • Pull downward, disengaged pawls.
    • Pull back instrument passenger lower cover.
    • Disconnect harness connector.
  9. Remove instrument side finisher (RH).
    • Insert a remover into lower space.
    • Pull the instrument side finisher (RH) crosswise.
  10. Remove glove box cover with power tool.
  11. Remove instrument finisher B.
    • Remove instrument finisher B fixing screws.
    • Insert a remover into right space.
      • Fig 6: Removing Glove Box Cover With Power Tool
      G05212844Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Remove front pillar garnish (LH/RH). Refer to BODY SIDE TRIM
  13. Remove instrument side finisher (LH).
    • Insert a remover into lower space.
    • Pull the instrument side finisher (LH) crosswise.
      • Fig 7: Locating Instrument Side Finisher (LH)
      G05212845Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Remove instrument side finisher (LH).
  15. Remove instrument finisher A.
    • Insert a remover into upper space.
    • Pull back instrument finisher A.
      • Fig 9: Locating Instrument Finisher A
      G05212847Courtesy of NISSAN MOTOR CO., U.S.A.
  16. Remove instrument finisher C.
    • Insert a remover into upper space
    • Pull back instrument finisher C.
      • Fig 10: Removing Instrument Finisher C
      G05212848Courtesy of NISSAN MOTOR CO., U.S.A.
  17. Remove cluster lid A
    • Pull back.
      Fig 11: Identifying Cluster Lid A
      G05212849Courtesy of NISSAN MOTOR CO., U.S.A.
  18. Remove combination meter. Refer to "REMOVAL AND INSTALLATION OF COMBINATION METER ".
  19. Remove steering column cover with power tool.
  20. Remove upper ventilator grille. Refer to "DUCTS AND GRILLES ".
  21. Remove center ventilator grille.
    • Remove center ventilator grille fixing screws.
    • Insert a remover into rear lower space.
    • Pull up.
      Fig 12: Identifying Center Ventilator Grille
      G05212850Courtesy of NISSAN MOTOR CO., U.S.A.
  22. Remove multifunction switch. Refer to "MULTIFUNCTION SWITCH ".
  23. Remove front display unit. Refer to "FRONT DISPLAY UNIT ".
  24. Remove AV control unit. Refer to "AV CONTROL UNIT ".
  25. Remove front passenger air bag module mounting bolt and disconnect harness connector. Refer to "FRONT PASSENGER AIR BAG MODULE ".
  26. Remove side ventilator grille (RH/LH).
    • Insert a remover into lower space.
    • Pull back.
      Fig 13: Identifying Side Ventilator Grille (RH/LH)
      G05212851Courtesy of NISSAN MOTOR CO., U.S.A.
  27. Remove front defroster grille.
    • Insert a remover into back space.
    • Pull up front defroster grille.
    • Disconnect harness connector.
      Fig 14: Locating Front Defroster Grille
      G05212852Courtesy of NISSAN MOTOR CO., U.S.A.
  28. Remove instrument panel assembly fixing screws, and then remove instrument panel assembly.
    CAUTION: When removing instrument panel, 2 workers are required so as to prevent it from dropping.
scientia non olet · About LEMON Manuals