Intermittent Wiper Does Not Operate When Rain Sensor is Canceled

With CONSULT-II 

1. Select "IVMS" on CONSULT-II. And select "WIPER" on "SELECT TEST ITEM" screen.
2. Select "DATA MONITOR" on "SELECT DIAG MODE" screen.
3. Make sure that "INT SW" turns ON-OFF according to operation of front wiper switch.

   When front wiper switch is INT: INT SW ON 

   When front wiper switch is OFF: INT SW OFF 

   NOTE: When "DATA MONITOR" is operating, intermittent wiper does not operate.
   Fig 1: CONSULT II DATA MONITOR Screen

   Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II 

Check front wiper switch (INT) in switch monitor mode. Refer to , "SWITCH MONITOR ".

OK or NG 

• OK: GO TO 2.
• NG: Check the following.
  • Front wiper switch: Refer to , "FRONT WIPER SWITCH INSPECTION ".
  • Harness for open or short between BCM and front wiper switch
  • Front wiper switch ground circuit

With CONSULT-II 

Make sure "WIPR AUTO STP" changes from "IGN" to "GND" according to operation of front wiper switch.

Front wiper is stopped.: WIPR AUTO STP IGN 

Front wiper is operating.: WIPR AUTO STP GND 

Fig 2: CONSULT II DATA MONITOR Screen

Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II 

1. Turn ignition switch ON.
2. Turn front wiper switch to LO or HI position.
3. Check voltage between BCM harness connector and ground.
   BCM HARNESS CONNECTOR AND GROUND VOLTAGE
   
   

   Terminal			Condition	Voltage
   (+)		(-)
   Connector	Terminal
   E204	124	Ground	Moving	Approx. 0 V
   			Stopped	Battery voltage

OK or NG 

• OK: GO TO 3.
• NG: Check the following.
  • Front wiper motor
  • Front wiper motor ground circuit
  • Harness for open or short between BCM and front wiper motor
    Fig 3: Checking Voltage Between BCM Harness Connector And Ground

    Courtesy of NISSAN MOTOR CO., U.S.A.

With CONSULT-II 

Make sure that "IGN ON SW" turns ON-OFF according to operation of ignition switch.

When ignition switch is ON: IGN ON SW ON 

When ignition switch is ACC or OFF: IGN ON SW OFF 

Fig 4: CONSULT II DATA MONITOR Screen

Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II 

Check voltage between BCM harness connector M4 terminal 68 and ground.

When ignition switch is ON: Battery voltage 

When ignition switch is ACC or OFF: Approx. 0 V 

Fig 5: Checking Voltage Between BCM Harness Connector M4 Terminal 68 And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG 

• OK: GO TO 4.
• NG: Check the following.
  • 10A fuse [No. 1, located in fuse block (J/B) No. 1]
  • Harness for open or short between fuse and BCM

With CONSULT-II 

1. Select "IVMS" on CONSULT-II. And select "WIPER" on "SELECT TEST ITEM" screen.
2. Select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch "ON" screen.
4. Make sure that front wiper motor operates.

   Front wiper motor should operate. 

   NOTE: If CONSULT-II is not available, skip this procedure and refer to , "FRONT WIPER AND WASHER ACTIVATE INDIVIDUALLY BUT NOT IN COMBINATION ".

OK or NG 

• OK: Replace BCM.
• NG: Refer to , "FRONT WIPER AND WASHER ACTIVATE INDIVIDUALLY BUT INTERMITTENT WIPER AND WASHER COMBINATION DOES NOT OPERATE ".
  Fig 6: CONSULT II ACTIVE TEST Screen

  Courtesy of NISSAN MOTOR CO., U.S.A.