Monitored Item
WARNING: This page is about a different car, the 2005 Infiniti QX56. However, it is still accessible from the selected car via links, so may be relevant.
DATA MONITOR ITEMS
| Monitored Item [unit] | MAIN SIGNALS | ECU INPUT SIGNALS | SELECTION FROM MENU | Description |
|---|---|---|---|---|
| VHCL SPEED SE [km/h] or [mph] | X | X | X | Indicates vehicle speed calculated from wheel speed sensor signal. |
| SET VHCL SPD [km/h] or [mph] | X | X | Indicates set vehicle speed stored in ICC unit. | |
| THRTL OPENING[%] | X | X | X | Indicates throttle angle calculated from signal voltage of throttle position sensor. |
| ENGINE RPM [rpm] | X | X | Indicates engine speed read by ICC unit via CAN communication (ECM transmits engine speed via CAN communication). | |
| DISTANCE ADJ [SHOR/MID/LONG] | X | X | X | Indicates set distance stored in ICC unit. |
| WIPER SW [OFF/LOW/HIGH] | X | X | Indicates wiper [OFF/LOW/HIGH] status. | |
| MAIN SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from control switch signal. |
| SET/COAST SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from control switch signal. |
| CANCEL SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from control switch signal. |
| RESUME/ACC SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from control switch signal. |
| CRUISE OPE [ON/OFF] | X | X | Indicates whether vehicle speed is being controlled or not (ON means "controlling"). | |
| BRAKE SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from ICC brake switch signal. |
| STOP LAMP SW [ON/OFF] | X | X | X | Indicates [ON/OFF] status as judged from stop lamp switch signal. |
| RELEASE SW NO [ON/OFF] | X | X | Indicates [ON/OFF] status as judged from release switch signal. | |
| RELEASE SW NO [ON/OFF] | X | X | Indicates [ON/OFF] status as judged from release switch signal. ON when brake is depressed. OFF when brake is not depressed. | |
| RELEASE SW NC [ON/OFF] | X | X | Indicates [ON/OFF] status as judged from release switch signal. OFF when brake is depressed. ON when brake is not depressed. | |
| IDLE SW [ON/OFF] | X | X | Indicates [ON/OFF] status of idle switch read by ICC unit via CAN communication (ECM transmits ON/OFF status via CAN communication). | |
| GEAR [1, 2,3,4, 5] | X | X | Indicates A/T gear position read by ICC unit via CAN communication (TCM transmits gear position via CAN communication). | |
| BUZZER O/P [ON/OFF] | X | Indicates [ON/OFF] status of ICC warning output. | ||
| ICC WARNING | X |
NOTE:
This item is displayed but cannot be monitored.
|
||
| VHCL SPD AT [km/h] or [mph] | X | Indicates vehicle speed calculated from A/T vehicle speed sensor by ICC unit via CAN communication (TCM transmits A/T vehicle speed sensor signal via CAN communication). | ||
| PRESS SENS [bar] | X | X | X | Indicates brake fluid pressure value calculated from signal voltage of pressure sensor. |
| PRESS SENS 2 [bar] | X | X |
NOTE:
This item is displayed but cannot be monitored.
|
|
| D RANGE SW [ON/OFF] | X | X | Indicates [ON/OFF] status of "D" position read by ICC unit via CAN communication (TCM transmits ON/OFF condition of "D" position via CAN communication). | |
| AT OD OFF [ON/OFF] | X | Indicates [ON/OFF] status of OD cancel output under control. | ||
| NO RANGE SW [ON/OFF] | X | X | Indicates PNP switch signal read by ICC unit via CAN communication. (TCM transmits PNP switch signal via CAN communication) | |
| DISTANCE | X |
NOTE:
This item is displayed but cannot be monitored.
|
||
| RELATIVE SPD | X |
NOTE:
This item is displayed but cannot be monitored.
|
||
| STP LMP DRIVE [ON/OFF] | X | X | Indicates [ON/OFF] status of brake hold relay drive output. |