LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2018 >> Kona Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 365 (Rear Seat Assembly) >> Rear Seat Back Cover >> Repair Procedures >> Removal And Installation

Removal And Installation

WARNING: This page is about a different car, the 2023 Kia Seltos. However, it is still accessible from the selected car via links, so may be relevant.

[LH] 

CAUTION: Put on gloves to prevent hand injuries.

Information 

  1. Remove the rear seat assembly [LH].

    (Refer to Rear Seat - "REAR SEAT ASSEMBLY ")

  2. Push the lock pins, and remove the rear seat headrest (A).
    G13486472Courtesy of KIA MOTORS AMERICA, INC.
  3. Remove the rear seat back webbing guide (A) by using a remover.
    G13486473Courtesy of KIA MOTORS AMERICA, INC.
  4. After lifting up the cap (A) and loosening the mounting screw, remove the rear seat folding bezel (B).
    G13486474Courtesy of KIA MOTORS AMERICA, INC.
    G13486475Courtesy of KIA MOTORS AMERICA, INC.
  5. After lifting up the cap (A) and loosening the mounting screws, remove the rear back latch cover (B).
    G13486476Courtesy of KIA MOTORS AMERICA, INC.
    G13486477Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the cover (A), loosen the mounting bolt and separate the rear back armrest (B).
    G13486478Courtesy of KIA MOTORS AMERICA, INC.
    G13486479Courtesy of KIA MOTORS AMERICA, INC.
  7. After loosening the mounting screws, remove the rear back armrest cover (A).
    G13486480Courtesy of KIA MOTORS AMERICA, INC.
  8. Using a screwdriver or remover, remove the child anchor cover (A).
    G13486481Courtesy of KIA MOTORS AMERICA, INC.
  9. Zip off the rear seat back cover (A), and then pull it up.
    G13486482Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the protector (A) located in the bottom lower of the rear seat back.
    G13486483Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the protector (A) located in the bottom side of the rear seat back.
    G13486484Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the back board (A) after removing the hog-ring clips.
    G13486485Courtesy of KIA MOTORS AMERICA, INC.
  13. Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
    G13486486Courtesy of KIA MOTORS AMERICA, INC.
    G13486487Courtesy of KIA MOTORS AMERICA, INC.
  14. After removing the velcro tape (A) and hog - ring clips (B) inside the rear seat cushion cover, remove the seat cushion covering.
    G13486488Courtesy of KIA MOTORS AMERICA, INC.
  15. Remove the rear seat back cover (A) from the rear seat back pad.
    G13486489Courtesy of KIA MOTORS AMERICA, INC.
  16. To install, reinstall in reverse order of removal procedure.

    Information 

    • Make sure that the connectors are connected completely
    • Replace any damaged clips (or pin-type retainers).
    • To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).
    • Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).
    G13486490Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    CAUTION: Put on gloves to prevent hand injuries.
    NOTE:
    • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
    • When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
    • Take care not to bend or scratch the trim and panels.
  1. Remove the rear seat assembly [RH].

    (Refer to Rear Seat - "REAR SEAT ASSEMBLY ")

  2. Push the lock pins, and remove the rear seat headrest (A).
    G13486491Courtesy of KIA MOTORS AMERICA, INC.
  3. After lifting up the cap (A) and loosening the mounting screw, remove the rear seat folding bezel (B).
    G13486492Courtesy of KIA MOTORS AMERICA, INC.
    G13486493Courtesy of KIA MOTORS AMERICA, INC.
  4. After lifting up the cap (A) and loosening the mounting screws, remove the rear back latch cover (B).
    G13486494Courtesy of KIA MOTORS AMERICA, INC.
    G13486495Courtesy of KIA MOTORS AMERICA, INC.
  5. Using a screwdriver or remover, remove the child anchor cover (A).
    G13486496Courtesy of KIA MOTORS AMERICA, INC.
  6. Zip off the rear seat back cover (A), and then pull it up.
    G13486497Courtesy of KIA MOTORS AMERICA, INC.
  7. Remove the protector (A) located in the bottom lower of the rear seat back.
    G13486498Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the protector (A) located in the bottom side of the rear seat back.
    G13486499Courtesy of KIA MOTORS AMERICA, INC.
  9. Remove the back board (A) after removing the hog-ring clips.
    G13486500Courtesy of KIA MOTORS AMERICA, INC.
  10. Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
    G13486501Courtesy of KIA MOTORS AMERICA, INC.
    G13486502Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the rear seat back cover assembly (A) from the rear seat back frame.
    G13486503Courtesy of KIA MOTORS AMERICA, INC.
  12. After removing the velcro tape (A) and hog - ring clips (B) inside the rear seat cushion cover, remove the seat cushion covering.
    G13486504Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the rear seat back cover (A) from the rear seat back pad.
    G13486505Courtesy of KIA MOTORS AMERICA, INC.
  14. To install, reinstall in reverse order of removal procedure.

    Information 

    • Make sure that the connectors are connected completely.
    • Replace any damaged clips (or pin-type retainers).
    • To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).
    • Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).
    G13486506Courtesy of KIA MOTORS AMERICA, INC.
scientia non olet · About LEMON Manuals