General Information
WARNING: This page is about a different car, the 2021 Hyundai Kona. However, it is still accessible from the selected car via links, so may be relevant.
| BOLT (Nominal diameter) | NUT (Nominal diameter) |
|---|---|
| BOLT/NUT Normal screw | Torque Nm (kg.m, Ib-ft) | |||
|---|---|---|---|---|
| Nominal diameter. (mm) | Pitch [mm (in.)] | 4T | 8T | 10T |
| M5 | 0.8 (0.031) | 2.0 - 3.0 (0.2 - 0.3, 1.4 - 2.2) | 4.9 - 6.9 (0.5 - 0.7, 3.6 - 5.1) | 7.8 - 10.8 (0.8 - 1.1, 5.8 - 8.0) |
| M6 | 1 (0.039) | 2.9 - 4.9 (0.3 - 0.5, 2.2 - 3.6) | 8.8 - 12.7 (0.9 - 1.3, 6.5 - 9.4) | 13.7 - 18.6 (1.4 - 1.9, 10.1 - 13.7) |
| M8 | 1.25 (0.049) | 8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7) | 22.6 - 30.4 (2.3 - 3.1, 16.6 - 22.4) | 33.3 - 44.1 (3.4 - 4.5, 24.6 - 32.5) |
| M10 | 1.5 (0.059) | 16.7 - 22.6 (1.7 - 2.3, 12.3 - 16.6) | 45.1 - 60.8 (4.6 - 6.2, 33.3 - 44.8) | 65.7 - 88.3 (6.7 - 9.0, 48.5 - 65.1) |
| M12 | 1.75 (0.068) | 29.4 - 39.2 (3.0 - 4.0, 21.7 - 28.9) | 78.5 - 105.9 (8.0 - 10.8, 57.9 - 78.1) | 114.7 - 154.9 (11.7 - 15.8, 84.6 - 114.3) |
| M14 | 2 (0.078) | 47.1 - 63.7 (4.8 - 6.5, 34.7 - 47.0) | 125.5 - 169.7 (12.8 - 17.3, 92.6 - 125.1) | 183.4 - 249.1 (18.7 - 25.4, 135.3 - 183.7) |
| M16 | 2 (0.078) | 73.5 - 100.0 (7.5 - 10.2, 54.2 - 73.8) | 197.1 - 266.7 (20.1 - 27.2, 145.4 - 196.7) | 288.3 - 390.3 (29.4 - 39.8, 212.7 - 287.9) |
| M20 | 2.5 (0.098) | 144.2 - 195.2 (14.7 - 19.9, 106.3 - 143.9) | 396.2 - 535.4 (40.4 - 54.6, 292.2 - 394.9) | 565.8 - 764.9 (57.7 - 78.0, 417.3 - 564.2) |
| M24 | 3 (0.118) | 249.1 - 337.3 (25.4 - 34.4, 183.7 - 248.8) | 687.4 - 929.7 (70.1 - 94.8, 507.0 - 685.7) | 975.8 - 1320.0 (99.5 - 134.6, 719.7 - 973.6) |
| M30 | 3.5 (0.137) | 499.2 - 674.7 (50.9 - 68.8, 368.2 - 497.6) | 1372.9 - 1858.4 (140.0 - 189.5, 1012.6 - 1370.7) | 1956.4 - 2647.8 (199.5 - 270.0, 1443.0 - 1952.9) |
| BOLT/NUT Thin screw | Torque Nm (kg.m, Ib-ft) | |||
|---|---|---|---|---|
| Nominal diameter. (mm) | Pitch [mm (in.)] | 4T | 8T | 10T |
| M5 | 0.5 (0.019) | 2.0 - 3.0 (0.2 - 0.3, 1.4 - 2.2) | 5.9 - 8.8 (0.6 - 0.9, 4.3 - 6.5) | 8.8 - 12.7 (0.9 - 1.3, 6.5 - 9.4) |
| M6 | 0.75 (0.029) | 3.9 - 4.9 (0.4 - 0.5, 2.9 - 3.6) | 9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1) | 14.7 - 20.6 (1.5 - 2.1, 10.8 - 15.2) |
| M8 | 1 (0.039) | 8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7) | 24.5 - 32.4 (2.5 - 3.3, 18.1 - 23.9) | 35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4) |
| M10 | 1.25 (0.049) | 17.7 - 23.5 (1.8 - 2.4, 13.0 - 17.4) | 47.1 - 63.7 (4.8 - 6.5, 34.7 - 47.0) | 69.6 - 94.1 (7.1 - 9.6, 51.4 - 69.4) |
| M12 | 1.25 (0.049) | 32.4 - 44.1 (3.3 - 4.5, 23.9 - 32.5) | 86.3 - 117.7 (8.8 - 12.0, 63.7 - 86.8) | 127.5 - 172.6 (13.0 - 17.6, 94.0 - 127.3) |
| M14 | 1.5 (0.059) | 51.0 - 69.6 (5.2 - 7.1, 37.6 - 51.4) | 136.3 - 185.3 (13.9 - 18.9, 100.5 - 136.7) | 201.0 - 271.6 (20.5 - 27.7, 148.3 - 200.4) |
| M16 | 1.5 (0.059) | 79.4 - 107.9 (8.1 - 11.0, 58.6 - 79.6) | 211.8 - 286.4 (21.6 - 29.2, 156.2 - 211.2) | 311.8 - 421.7 (31.8 - 43.0, 230.0 - 311.0) |
| M20 | 1.5 (0.059) | 163.8 - 221.6 (16.7 - 22.6, 120.8 - 163.5) | 448.2 - 607.0 (45.7 - 61.9, 330.5 - 447.7) | 639.4 - 864.9 (65.2 - 88.2, 471.6 - 638.0) |
| M24 | 2 (0.078) | 276.5 - 373.6 (28.2 - 38.1, 204.0 - 275.6) | 759.0 - 1026.8 (77.4 - 104.7, 559.8 - 757.3) | 1080.7 - 1462.2 (110.2 - 149.1, 797.1 - 1078.4) |
| M30 | 2 (0.078) | 562.9 - 762.0 (57.4 - 77.7, 415.2 - 562.0) | 1553.4 - 2102.5 (158.4 - 214.4, 1145.7 - 1550.8) | 2210.4 - 2991.0 (225.4 - 305.0, 1630.3 - 2206.1) |
| Flange BOLT (Nominal diameter) | Flange NUT (Nominal diameter) |
|---|---|
| Flange BOLT/NUT Normal screw | Torque Nm (kg.m, Ib-ft) | |||
|---|---|---|---|---|
| Nominal diameter. (mm) | Pitch [mm (in.)] | 4T | 8T | 10T |
| M5 | 0.8 (0.031) | 2.0 - 2.9 (0.2 - 0.3, 1.4 - 2.2) | 5.9 - 7.8 (0.6 - 0.8, 4.3 - 5.8) | 8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7) |
| M6 | 1 (0.039) | 3.9 - 4.9 (0.4 - 0.5, 2.9 - 3.6) | 9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1) | 14.7 - 19.6 (1.5 - 2.0, 10.8 - 14.5) |
| M8 | 1.25 (0.049) | 8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7) | 24.5 - 32.4 (2.5 - 3.3, 18.1 - 23.9) | 35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4) |
| M10 | 1.5 (0.059) | 17.7 - 24.5 (1.8 - 2.5, 13.0 - 18.1) | 48.1 - 65.7 (4.9 - 6.7, 35.4 - 48.5) | 70.6 - 96.1 (7.2 - 9.8, 52.1 - 70.9) |
| M12 | 1.75 (0.068) | 31.4 - 43.1 (3.2 - 4.4, 23.1 - 31.8) | 84.3 - 113.8 (8.6 - 11.6, 62.2 - 83.9) | 123.6 - 167.7 (12.6 - 17.1, 91.1 - 123.7) |
| M14 | 2 (0.078) | 51.0 - 68.6 (5.2 - 7.0, 37.6 - 50.6) | 135.3 - 182.4 (13.8 - 18.6, 99.8 - 134.5) | 198.1 - 268.7 (20.2 - 27.4, 146.1 - 198.2) |
| M16 | 2 (0.078) | 79.4 - 107.9 (8.1 - 11.0, 58.6 - 79.6) | 212.8 - 288.3 (21.7 - 29.4, 157.0 - 212.7) | 311.8 - 421.7 (31.8 - 43.0, 230.0 - 311.0) |
| Flange BOLT/NUT Thin screw | Torque Nm (kg.m, Ib-ft) | |||
|---|---|---|---|---|
| Nominal diameter. (mm) | Pitch [mm (in.)] | 4T | 8T | 10T |
| M5 | 0.5 (0.019) | 2.9 - 2.9 (0.3 - 0.3, 2.2 - 2.2) | 6.9 - 8.8 (0.7 - 0.9, 5.1 - 6.5) | 9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1) |
| M6 | 0.75 (0.029) | 3.9 - 5.9 (0.4 - 0.6, 2.9 - 4.3) | 10.8 - 14.7 (1.1 - 1.5, 8.0 - 10.8) | 16.7 - 21.6 (1.7 - 2.2, 12.3 - 15.9) |
| M8 | 1 (0.039) | 9.8 - 12.7 (1.0 - 1.3, 7.2 - 9.4) | 26.5 - 35.3 (2.7 - 3.6, 19.5 - 26.0) | 38.2 - 52.0 (3.9 - 5.3, 28.2 - 38.3) |
| M10 | 1.25 (0.049) | 19.6 - 25.5 (2.0 - 2.6, 14.5 - 18.8) | 51.0 - 68.6 (5.2 - 7.0, 37.6 - 50.6) | 75.5 - 102.0 (7.7 - 10.4, 55.7 - 75.2) |
| M12 | 1.25 (0.049) | 35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4) | 94.1 - 126.5 (9.6 - 12.9, 69.4 - 93.3) | 138.3 - 186.3 (14.1 - 19.0, 102.0 - 137.4) |
| M14 | 1.5 (0.059) | 55.9 - 75.5 (5.7 - 7.7, 41.2 - 55.7) | 148.1 - 200.1 (15.1 - 20.4, 109.2 - 147.6) | 216.7 - 293.2 (22.1 - 29.9, 159.8 - 216.3) |
| M16 | 1.5 (0.059) | 86.3 - 116.7 (8.8 - 11.9, 63.7 - 86.1) | 229.5 - 309.9 (23.4 - 31.6, 169.3 - 228.6) | 336.4 - 455.0 (34.3 - 46.4, 248.1 - 335.6) |
NOTE:
- The torques shown in the table are standard values under the following conditions.
- Nuts and bolts are made of galvanized steel bar.
- Galvanized plain steel washers are inserted.
- All nuts, bolts and plain washers are dry.
- The torques shown in the table are not applicable.
- When spring washers, toothed washers and the like are inserted.
- If plastic parts are fastened.
- If self-tapping screws or self-locking nuts are used.
- If threads and surfaces are coated with oil.