Repair Procedures: Installation

1. Using a gasket scraper, remove all the old packing material from the gasket surfaces.
2. The sealant locations on chain cover and on counter parts (cylinder head, cylinder block, and ladder frame) must be free of engine oil and etc.
3. Before assembling the timing chain cover, liquid sealant Loctite 5900H or equivalent should be applied on the gap between camshaft front bearing cap, cylinder head and cylinder block. The part must be assembled within 5 minutes after sealant was applied.

   Bead width:  2.0 - 3.0 mm (0.08 - 0.12 in.)

   Fig 1: Sealant Locations On Chain Cover And Counter Parts

   Courtesy of HYUNDAI MOTOR AMERICA
4. After applying liquid sealant Loctite 5900H or equivalent on the timing chain cover.

   The part must be assembled within 5 minutes after sealant was applied. Continuous bead of sealant should be applied to prevent any path of oil leakage.

   Bead width:  2.0 - 3.0 mm (0.08 - 0.12 in.)

   Fig 2: Timing Chain Cover Liquid Sealant Applying Area

   Courtesy of HYUNDAI MOTOR AMERICA
5. The dowel pins on the cylinder block and holes on the timing chain cover should be used as a mark in order to assemble the timing chain cover to be in exact position.

   Tightening torque 

   M6 X 25 bolt:

   7.8 - 9.8 N.m (0.8 - 1.0 kgfm, 5.8 - 7.2 lbft)

   M8 X 28 bolt:

   18.6 - 22.6 N.m (1.9 - 2.3 kgfm, 13.7 - 16.6 lbft)

   Fig 3: Identifying Timing Chain Cover Bolts

   Courtesy of HYUNDAI MOTOR AMERICA
   NOTE: The engine starting or pressure tests should not be performed within 30 minutes after the timing chain cover was assembled.

(Refer to Timing System - "FRONT OIL SEAL ")

(Refer to Timing System - "DRIVE BELT TENSIONER ")

1. If there is sign of leakage from inside the E-CVVT cover, replace it with a new one.
2. Check for worn connector brush.

   Specification:  Over 5 mm (0.1969 in.)

   Fig 6: Checking Worn Connector Brush

   Courtesy of HYUNDAI MOTOR AMERICA

   If measurement is below specification, replace the E-CVVT cover with a new one.

3. Check for damaged oil seal (A) and replace any damaged E-CVVT cover with a new one.
   Fig 7: Locating Damaged Oil Seal

   Courtesy of HYUNDAI MOTOR AMERICA
4. After inspecting E-CVVT, if no problem is found, replace the o-ring (A) with a new one.
   Fig 8: Locating O-Ring

   Courtesy of HYUNDAI MOTOR AMERICA

1. Apply engine oil on oil seal lip (A).
   Fig 9: Locating Engine Oil Applying Area On Oil Seal Lip

   Courtesy of HYUNDAI MOTOR AMERICA
   NOTE: When applying oil, keep the connector brush (A) clean from foreign materials.
   Fig 10: Locating Connector Brush

   Courtesy of HYUNDAI MOTOR AMERICA
2. Insert SST (09243-C2000) into the E-CVVT motor shaft.
   Fig 11: Inserting SST (09243-C2000) Into E-CVVT Motor Shaft

   Courtesy of HYUNDAI MOTOR AMERICA
   NOTE:

   • Correctly mount SST onto the motor shaft.
3. Slowly push the E-CVVT cover (A) until it is flush with the timing chain cover surface.
   Fig 12: Pushing E-CVVT Cover With Timing Chain Cover Surface

   Courtesy of HYUNDAI MOTOR AMERICA
   NOTE:

   • Installing the E-CVVT cover without SST may cause oil leakage inside the E-CVVT motor due to damaged or separated E-CVVT oil seal.
4. Pre-tighten the bolts in the below sequence, and then remove the SST (09243-C2000).

   Tightening torque: 

   1.0 - 2.0 N.m (0.1 - 0.2 kgfm, 0.7 - 1.4 lbft)

   Fig 13: Identifying SST (09243-C2000)

   Courtesy of HYUNDAI MOTOR AMERICA
5. Tighten the bolts to the specified torque in the sequence below.

   Tightening torque: 

   9.8 - 11.8 N.m (1.0 - 1.2 kgfm, 7.2 - 8.7 lbft)

   Fig 14: E-CVVT Cover Bolts Tightening Sequence

   Courtesy of HYUNDAI MOTOR AMERICA

1. By using SST (09243-C2000), insert the plug (A) into the E-CVVT cover hole.
   Fig 15: Inserting Plug Into E-CVVT Cover Hole

   Courtesy of HYUNDAI MOTOR AMERICA
   NOTE:

   • Do not reuse a E-CVVT motor plug.
2. Mount the stopper of SST so that it sits at the end of E-CVVT motor shaft.
   Fig 16: Mounting Stopper Of SST End Of E-CVVT Motor Shaft

   Courtesy of HYUNDAI MOTOR AMERICA

1. By using a steel ruler, measure the distance from E-CVVT cover center boss to the end of motor shaft (1).
2. By using a steel ruler, measure the distance from E-CVVT cover center boss to the end of E-CVVT plug (2).
   Fig 17: Measuring Distance From E-CVVT Cover Center Boss To End Of E-CVVT Plug

   Courtesy of HYUNDAI MOTOR AMERICA
3. Calculate the pressed depth (3) of motor plug.

   If out of specification, reinstall after replacing the E-CVVT plug with a new one.

   Pressed depth:  (3) = (2)-(1)

   Specification:  1.9 - 2.1 mm (0.0748 - 0.0827 in.)

Fig 18: Locating E-CVVT Cover Plug Protrusion

Courtesy of HYUNDAI MOTOR AMERICA

Fig 19: Locating E-CVVT Cover Groove

Courtesy of HYUNDAI MOTOR AMERICA

Fig 20: Checking E-CVVT Plug

Courtesy of HYUNDAI MOTOR AMERICA

• Be careful that the plug is not inserted inside E-CVVT cover beyond the regulated range.

Tightening torque: 

Bolt B: 4.0 - 4.5 kgfm

Bolt C: 2.0 - 2.5 kgfm

1. Install in order of 1→2→3 temporary.
2. Turn the bracket counterclockwise and install the bolt 1.
3. Install in order of 2→3→4→5→6.

Fig 21: Installing Engine Support Bracket

Courtesy of HYUNDAI MOTOR AMERICA