LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2015 >> Veloster Turbo, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Interior Trim And Glass >> Interior Trim >> Repair Procedures >> Replacement >> Center Pillar Trim Replacement

Center Pillar Trim Replacement

CAUTION:
  • Put on gloves to protect your hands.
  • Use a plastic panel removal tool to remove interior trim pieces to without marring the surface.
  • Take care not to bend or scratch the trim and panels.
  1. Remove the following parts first:
    1. Front Door Scuff Trim

      (Refer to: BD procedure - "INTERIOR TRIM ").

    2. Rear Door Scuff Trim [RH]

      (Refer to: BD procedure - "INTERIOR TRIM ").

  2. Disconnect the Battery Negative Cable and wait for at least three minutes before beginning work.
  3. The Seat Belt Anchor Pretensioner (A) can be removed after pushing the Lock Pin (B) as arrow directed.

    [LH] 

    Fig 1: Pushing Lock Pin (LH) (1 Of 2)
    G10605470Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 2: Pushing Lock Pin (RH) (2 Of 2)
    G10605471Courtesy of HYUNDAI MOTOR AMERICA
  4. Using a screwdriver or remover, remove the Center Pillar Lower Trim (A).

    [LH] 

    Fig 3: Center Pillar Lower Trim (LH) (1 Of 2)
    G10605472Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 4: Center Pillar Lower Trim (RH) (2 Of 2)
    G10605473Courtesy of HYUNDAI MOTOR AMERICA
  5. Using a screwdriver or remover, remove the Front Seat Belt Upper Anchor Cover (A).

    [LH] 

    Fig 5: Front Seat Belt Upper Anchor Cover (LH) (1 Of 2)
    G10605474Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 6: Front Seat Belt Upper Anchor Cover (RH) (2 Of 2)
    G10605475Courtesy of HYUNDAI MOTOR AMERICA
  6. After loosening the Mounting Bolt, remove the Front Seat Belt Upper Anchor (A).

    [LH] 

    Tightening Torque: 

    39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

    Fig 7: Front Seat Belt Upper Anchor Mounting Bolt (LH) (1 Of 2)
    G10605476Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Tightening Torque: 

    39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

    Fig 8: Front Seat Belt Upper Anchor Mounting Bolt (RH) (2 Of 2)
    G10605477Courtesy of HYUNDAI MOTOR AMERICA
  7. After loosening the Mounting Bolt, remove the Center Pillar Upper Trim (A).

    [LH] 

    Fig 9: Loosening Center Pillar Upper Trim Mounting Bolt (LH) (1 Of 2)
    G10605478Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 10: Loosening Center Pillar Upper Trim Mounting Bolt (RH) (2 Of 2)
    G10605479Courtesy of HYUNDAI MOTOR AMERICA
  8. Installation is the reverse of removal.
    NOTE:
    • Replace any damaged clips.