LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (Lighting) >> Diagnostic Information and Procedures >> DTC B2575 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Hummer H2. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  This step tests for voltage at the voltage supply side of the headlamp low beam relay.
  2. 4:  This step verifies that the BCM is providing ground to the headlamp low beam relay.
  3. 5:  This step tests if ground is constantly being applied to the headlamp low beam relay.
  4. 6:  This step tests if there is opposing voltage present or an open headlamp low beam relay control circuit, including the relay coil side.
  5. 12:  After replacement of the BCM you must calibrate the new module for proper operation.
DTC B2575

Step Action Yes No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics 
Connector End View Reference: Lighting Systems Connector End Views  or Data Communication Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition, with the engine OFF.
  2. Place the headlamp switch in the ON position.
  3. Place the headlamp dimmer switch in the low beam position.
  4. Place the headlamp switch in the OFF position.
Do the low beam headlamps operate as expected?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the headlamp low beam relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the control circuit of the headlamp low beam relay and a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4 
  1. Connect a test lamp between the control circuit of the headlamp low beam relay and the battery positive voltage circuit of the headlamp low beam relay.
  2. While observing the test lamp, place the headlamp switch in the ON position, and then the OFF position.
Does the test lamp turn ON and OFF with each cycle of the switch?		 Go to Step 8  Go to Step 5 
5  Does the test lamp remain illuminated with each cycle of the switch? Go to Step 7  Go to Step 6 
6  Test the control circuit of the headlamp low beam relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7 Test the control circuit of the headlamp low beam relay for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the headlamp low beam relay. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the battery positive voltage circuit of the headlamp low beam relay. Refer to Wiring Repairs .
Did you complete the repair?		 Go to Step 13  -
11 Replace the headlamp low beam relay. Refer to Relay Replacement (Attached to Wire Harness) or Relay Replacement (Within an Electrical Center) .
Did you complete the replacement?		 Go to Step 13  -
12  Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals