LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 5 (Instrument Panel And Console Trim) >> Repair Instructions >> Instrument Panel Carrier Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2007 Hummer H2. However, it is still accessible from the selected car via links, so may be relevant.
    IMPORTANT: Make sure the ambient light sensor is routed to the top of the I/P.
    Fig 1: Aligning I/P & Routing Electrical Harnesses
    GM815925Courtesy of GENERAL MOTORS CORP.
  1. Align the I/P in the vehicle and route all electrical harnesses through the I/P retainer.
    2. NOTE: Refer to Fastener Notice .
  2. Install the upper and side I/P carrier bolts.

    Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

    3. Fig 2: I/P Carrier Center Support Bracket Nut
    GM832818Courtesy of GENERAL MOTORS CORP.
  3. Install the I/P carrier center support nut.

    Tighten:  Tighten the nut to 9 N.m (80 lb in).

    4. Fig 3: Front Assist Handle
    GM922456Courtesy of GENERAL MOTORS CORP.
  4. Install the windshield garnish moldings. Refer to Windshield Pillar Garnish Molding Replacement .
  5. Install the upper HVAC air temperature sensors from the HVAC ducts. Refer to Air Temperature Sensor Replacement - Upper Right Side and Air Temperature Sensor Replacement - Upper Left Side for the automatic system.
  6. Install the lower HVAC air temperature sensors from the HVAC ducts. Refer to Air Temperature Sensor Replacement - Lower Left Side and Air Temperature Sensor Replacement - Lower Right Side for the automatic system.
    7. Fig 4: Driver Knee Bolster
    GM816351Courtesy of GENERAL MOTORS CORP.
  7. Install the steering column. Refer to Steering Column Replacement .
    8. Fig 5: Knee Bolster Trim Panel
    GM832830Courtesy of GENERAL MOTORS CORP.
  8. Install the drivers knee bolster. Refer to Driver Knee Bolster Panel Replacement .
    9. Fig 6: I/P Air Bag Module
    GM815846Courtesy of GENERAL MOTORS CORP.
  9. Install the I/P air bag module. Refer to Inflatable Restraint Instrument Panel Module Replacement .
    10. Fig 7: I/P Compartment
    GM832822Courtesy of GENERAL MOTORS CORP.
  10. Install the I/P storage compartment. Refer to Instrument Panel Compartment Replacement .
    11. Fig 8: Headlamp Switch
    GM815903Courtesy of GENERAL MOTORS CORP.
  11. Install the headlamp switch. Refer to Headlamp Switch Replacement .
    12. Fig 9: Rear Wiper Switch
    GM815902Courtesy of GENERAL MOTORS CORP.
  12. Install the rear wiper switch. Refer to Rear Window Wiper and Washer Switch Replacement .
    13. Fig 10: Transfer Case Control Switch Module
    GM815899Courtesy of GENERAL MOTORS CORP.
  13. Install the transfer case control switch module. Refer to Transfer Case Shift Control Module Replacement for the BW 4484 transfer case.
    14. Fig 11: Traction Control & Air Ride Switch Module Assembly
    GM815914Courtesy of GENERAL MOTORS CORP.
  14. Install the traction control, air ride module to center stack and make electrical connections.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    15. Fig 12: Identifying Radio
    GM815852Courtesy of GENERAL MOTORS CORP.
  15. Install the radio. Refer to Radio Replacement .
    16. Fig 13: Communication Interface Module & I/P
    GM815865Courtesy of GENERAL MOTORS CORP.
  16. Install the OnStar® module from center stack. Refer to OnStar Button Assembly Replacement .
    17. Fig 14: HVAC Control
    GM815858Courtesy of GENERAL MOTORS CORP.
  17. Install the HVAC control. Refer to HVAC Control Module Replacement for the automatic system.
    18. Fig 15: Right Trim Panel Accessory
    GM832820Courtesy of GENERAL MOTORS CORP.
  18. Install the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement .
    19. Fig 16: I/P Cluster Electrical Connections
    GM816329Courtesy of GENERAL MOTORS CORP.
  19. Install the IPC cluster and trim panel. Refer to Instrument Cluster Replacement .
    20. Fig 17: View Of Data Link Connector Retaining Bolts/Screws
    GM386625Courtesy of GENERAL MOTORS CORP.
  20. Install the diagnostic connector to the I/P.
  21. Tighten the data link connector screws.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  22. Connect brake release lever to I/P.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    23. Fig 18: I/P Accessory Left Trim Panel
    GM816356Courtesy of GENERAL MOTORS CORP.
  23. Install the left accessory trim panel. Refer to Instrument Panel Accessory Trim Plate Replacement - Left Side .
    24. Fig 19: I/P Accessory Right Trim Panel
    GM816334Courtesy of GENERAL MOTORS CORP.
  24. Install the right accessory trim panel. Refer to Instrument Panel Accessory Trim Plate Replacement - Right Side .
    25. Fig 20: I/P Assist Handle
    GM816332Courtesy of GENERAL MOTORS CORP.
  25. Install the assist handle. Refer to Instrument Panel Assist Handle Replacement .
    26. Fig 21: I/P Center Trim Panel
    GM832824Courtesy of GENERAL MOTORS CORP.
  26. Install the I/P center trim panel. Refer to Instrument Panel Center Trim Panel Replacement .
    27. Fig 22: Left & Right I/P Side Trim
    GM816365Courtesy of GENERAL MOTORS CORP.
  27. Align the drivers and passenger side I/P side trim panel and snap into place.
    28. Fig 23: I/P Center Console
    GM816362Courtesy of GENERAL MOTORS CORP.
  28. Install the I/P center console. Refer to Console Replacement .
    29. Fig 24: Locating I/P Insulator Retaining Bolts
    GM787371Courtesy of GENERAL MOTORS CORP.
  29. Install the passengers insulator. Refer to Instrument Panel Insulator Replacement .
scientia non olet · About LEMON Manuals