LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 482 (Rear Drive Axle) >> Repair Instructions >> Locking Differential Adjustment (10.5 Inch Axle) >> Thrust Block Clearance Adjustment

Thrust Block Clearance Adjustment

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2012 GMC Yukon XL, 2012 GMC Yukon, 2012 Chevrolet Tahoe, 2012 Chevrolet Suburban, and 2012 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

The left and right side gear backlash measurements must be done before the thrust block measurement can be completed.

    Fig 1: View Of Left Side Gear Thrust Washer
    GM882831Courtesy of GENERAL MOTORS COMPANY
  1. Install the differential side gear shim.
    2. Fig 2: Left Side Clutch Plates & Guide Clips
    GM882829Courtesy of GENERAL MOTORS COMPANY
  2. Install the clutch pack assembly.
    3. Fig 3: Locking Differential Side Gear
    GM882828Courtesy of GENERAL MOTORS COMPANY
  3. Install the differential side gear.
  4. Assemble a set of washers, a nut, and a bolt long enough in order to hold the side gear in place.
    5. Fig 4: Installing Bolt & Washer Assembly Through Differential Case Half
    GM882839Courtesy of GENERAL MOTORS COMPANY
  5. Install the bolt and washer assembly through the differential case half.
  6. Install a second set of washers and the nut onto the bolt extending through the differential case half.
  7. Install the differential case half into a vise.
  8. Clamp on the nut on the bottom of the differential case.
  9. Tighten the bolt until the clutch plates are compressed.
    10. Fig 5: J 34672 & J 34673
    GM882843Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    To perform the following measurement procedure, 2 of the J 34673  bar will be needed.

  10. Install the J 34673  bar (2) and the J 34672  micrometer (1) onto the differential case as shown in illustration.
  11. Install the J 34673  bar onto the face of the differential case, not the ridge of the differential case, or an inaccurate measurement will result.
  12. Using the J 34672  micrometer and the J 34673  bar, measure and record the depth from the face of the to the face of the differential side gear.
  13. Measure the thickness of the J 34673  bar subtract from the measurement obtained in step 10 and record the measurement. This measurement is equal to one-half of the thrust block thickness.
  14. Remove the differential case half from the vise.
    15. Fig 6: Right Side Locking Differential Clutch Disc Thrust Washer
    GM882850Courtesy of GENERAL MOTORS COMPANY
  15. Install the locking differential clutch disc thrust washer.
    16. Fig 7: Right Side Cam Unit & Clutch Plate Assembly
    GM882834Courtesy of GENERAL MOTORS COMPANY
  16. Install the differential side gear cam unit.
  17. Assemble a set of washers, a nut, and a bolt long enough in order to hold the side gear in place.
    18. Fig 8: Bolt & Washer Assembly Through Differential Case Half
    GM882845Courtesy of GENERAL MOTORS COMPANY
    NOTE:
    • The bolt must be long enough to hold the differential side gear in place and to allow the use of washers and nut.
    • The washers must be the proper size in order to fit over the differential side gear, but without causing interference with the with the differential pinion gear and differential spider assembly.
    • Tighten the nut and bolt just enough compress the clutch disc but will allow locking differential side gear to rotate.
  18. Install the long bolt, washers and nut
  19. Install the differential case half into a vise.
  20. Clamp on the nut on the bottom of the differential case.
    21. Fig 9: Flat Gauge Bat And Micrometer Tools
    GM882847Courtesy of GENERAL MOTORS COMPANY
  21. Install the J 34673  bar (2) and the J 34672  micrometer (1) onto the differential case.
  22. Using the J 34673  bar and the J 34672  micrometer, measure and record the depth from the face of the to the face of the differential side gear.
    23. NOTE:

    This measurement is equal to one-half of the thrust block thickness.

  23. Measure the thickness of the J 34673  bar subtract from the measurement obtained in step 23.
  24. Add the measurements in step 12 and step 25 together. This is the thickness for the thrust block.
    25. NOTE:
    • If the measurement is equal to one of the thrust block sizes available, the select that thrust block.
    • If the measurement is less than one of the thrust block sizes available, then select the next smaller thrust block.
  25. Compare the measurement obtain in step 25 to the thrust block sizes available.
    26. NOTE:

    The backlash must be rechecked and adjusted to specification anytime the left and/or the right thrust washers are replaced.

  26. If the measurement obtained in step 25 is less then 40.488 mm (1.594 in), then reduce the left differential side gear shim or the right locking differential clutch disc thrust washer thickness in order to increase the thrust block opening.
  27. If the measurement obtained in step 25 is greater then 41.120 mm (1.622 in), then increase the left differential side gear shim or the right locking differential clutch disc thrust washer thickness in order to decrease the thrust block opening.
  28. Recheck the left and/or right side gear backlash and adjust as necessary.
  29. Recheck the thrust block clearance and adjust as necessary.
scientia non olet · About LEMON Manuals