Fastener Tightening Specifications
WARNING: This page is about a different car, the 2011 GMC Yukon, 2011 Chevrolet Tahoe, and 2011 Cadillac Escalade. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Ref No. * | Quantity | Size | Specification | |
|---|---|---|---|---|---|
| Metric | English | ||||
| A/Trans Auxiliary Fluid Pump Bolt - to Torque Dampener Housing | 5 | 4 | M6 x 1.0 x 65 | 9-13 N.m | 80-115 lb in |
| A/Trans Fluid Pan Bolt - to Case Assembly | 53 | 13 | M8 x 1.25 x 20 | 24-29 N.m | 18-21 lb ft |
| A/Trans Fluid Pump Cover Bolt - Torque Dampener to Case Assembly | 3 | 12 | M8 x 1.25 x 25 | 26.5-31.5 N.m | 19.55-23.23 lb ft |
| A/Trans Fluid Pump Cover Bolt - to Torque Dampener Housing Assembly | 228 | 18 | M6 x 1.0 x 45 | 9-13 N.m | 80-115 lb in |
| A/Trans Manual Shift Shaft Position Switch Bolt | 32 | 1 | M5 x 0.8 x 20 | 7-9 N.m | 62-80 lb in |
| A/Trans Rear Case Bolt - to Case Assembly | 27 | 12 | M8 x 1.25 x 30 | 26.5-31.5 N.m | 19.55-23.23 lb ft |
| A/Trans Rear Case Bolt - 2WD Output Housing Extension Assembly to Rear Case Assembly | 22 | 6 | M10 x 1.5 x 45 | 51-61 N.m | 38-45 lb ft |
| A/Trans Torque Dampener Fluid Passage Plug - to Torque Dampener Housing | 8 | 1 | Inch Series 0.4375-20 | 9-13 N.m | 80-115 lb in |
| A/Trans Torque Dampener Fluid Passage Plug - to Torque Dampener Housing | 9 | 1 | Inch Series 0.4375-20 | 9-13 N.m | 80-115 lb in |
| Control Solenoid Valve Heat Sink (w/Body and TCM) Bolt | 306 | 2 | M5 x 0.8 x 53 | 5-8 N.m | 44-71 lb in |
| Center Support Bolt | 87 | 4 | M6 x 1.0 x 20 | 9-13 N.m | 80-115 lb in |
| Control Valve Channel Plate Bolt | 300 | 20 | M6 x 1.0 x 35 | 9-13 N.m | 80-115 lb in |
| Control Valve Upper Body Bolt | 38 | 4 | M6 x 1.0 x 65 | 9-13 N.m | 80-115 lb in |
| Control Valve Upper Body Bolt | 37 | 2 | M6 x 1.0 x 80 | 9-13 N.m | 80-115 lb in |
| Control Valve Lower Body Bolt | 308 | 9 | M6 x 1.0 x 55 | 9-13 N.m | 80-115 lb in |
| Drain Plug Assembly - to Fluid Pan Assembly | 55 | 1 | Inch Series 0.125-27 NPTF | 30-40 N.m | 22-30 lb ft |
| Drive Motor Generator Power Inverter Module Cable Terminal Bracket Bolt (Captured Bolts, cannot be removed) | - | 6 | M6 x 1.0 x 15 | 9-13 N.m | 80-115 lb in |
| Generator Drive Motor Bolt | 70 | 6 | M6 x 1.0 x 20 | 9-13 N.m | 80-115 lb in |
| Electrical Harness Retaining Nut | - | - | - | 25 N.m | 18 lb ft |
| Electrical Harness Retaining Screw | - | - | - | 50 N.m | 37 lb ft |
| Fluid Cooler Pipe to Transmission Bolt | - | - | - | 22 N.m | 16 lb ft |
| Fluid Filler Tube Nut | - | - | - | 18 N.m | 13 lb ft |
| Fuel Pipe Bracket Nuts - 2WD | - | - | - | 50 N.m | 37 lb ft |
| Fuel Pipe Bracket Nuts - 4WD | - | - | - | 25 N.m | 18 lb ft |
| Fuel Line Bracket Screw | - | - | - | 7 N.m | 62 lb in |
| Hybrid Direct, 2-3-4 Clutch Support Bolt - to Rear Case Assembly | 443 | 9 | M6 x 1.0 x 20 | 9-13 N.m | 80-115 lb in |
| Manual Shift Detent Spring Bolt | 40 | 1 | M6 x 1.0 x 16 | 9-13 N.m | 80-115 lb in |
| Park Pawl Cover Bolt - to Rear Case Assembly | 454 | 5 | M6 x 1.0 x 20 | 9-13 N.m | 80-115 lb in |
| Power Inverter Module Cable Cover Bolt - to Case Assembly | 16 | 4 | M6 x 1.0 | 9-13 N.m | 80-115 lb in |
| Power Inverter Module Cable Retaining Bolt - to Case Assembly | 14 | 4 | M6 x 1.0 x 15 | 9-13 N.m | 80-115 lb in |
| Range Selector Lever Heat Shield Bolts | - | - | - | 17 N.m | 13 lb ft |
| Range Selector Lever Nuts | - | - | - | 25 N.m | 18 lb ft |
| Torque Dampener to Flex Plate Bolts | - | - | - | 65 N.m | 48 lb ft |
| Transmission to Engine Bolts | - | - | - | 50 N.m | 37 lb ft |
| Transmission Mount to Crossmember Nuts | - | - | - | 55 N.m | 40 lb ft |
| Transmission Mount to Transmission Bolts | - | - | - | 67 N.m | 50 lb ft |
| Transmission to Transfer Case Nuts | - | - | - | 50 N.m | 37 lb ft |
| Transmission Range Selector Lever Nut | - | - | - | 25 N.m | 18 lb ft |
| Transmission Range Selector Lever Cable Heat Shield Bolts | - | - | - | 17 N.m | 13 lb ft |
| Vehicle Speed Sensor Bolt - Output Speed Sensor to Rear Case Assembly | 446 | 1 | M6 x 1.0 x 20 | 9-13 N.m | 80-115 lb in |
| *Reference number refers to the component callout number in Disassembled Views | |||||