LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 344 (Engine Mechanical - 5.3L, 6.0L & 6.2L - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Valve Rocker Arm Cover Replacement - Right Side >> Removal Procedure

Removal Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: CPA Retainer, Engine Harness Electrical Connectors And Harness Clips
    GM1696893Courtesy of GENERAL MOTORS CORP.
  1. Remove the intake manifold cover. Refer to Upper Intake Manifold Sight Shield Replacement .
  2. Remove the connector position assurance (CPA) retainer (2).
  3. Disconnect the engine harness electrical connector (1) from the ignition coil wire harness.
  4. Remove the engine wiring harness (electronic throttle control branch) clip (6) from the ignition coil bracket stud.
  5. Reposition the engine wiring harness (electronic throttle control branch) as necessary.
    6. Fig 2: Generator Battery Jumper Cable
    GM1699546Courtesy of GENERAL MOTORS CORP.
  6. Remove the generator battery cable clip (1) from the ignition coil bracket stud.
  7. Reposition the generator battery cable as necessary.
    8. Fig 3: Heater Inlet Hose, Clamp And Water Pump
    GM1697282Courtesy of GENERAL MOTORS CORP.
  8. Remove the heater inlet hose (2) from the heater hose bracket (3).
    9. Fig 4: Radiator Surge Tank Outlet Hose, Clamp And Water Pump
    GM1697283Courtesy of GENERAL MOTORS CORP.
  9. Remove the surge tank outlet hose (2) from the heater hose bracket (3).
    10. Fig 5: Heater Hose Bracket And Nut
    GM1697280Courtesy of GENERAL MOTORS CORP.
  10. Remove the heater hose bracket nut and bracket
    11. Fig 6: Ignition Coil And Bracket
    GM1402028Courtesy of GENERAL MOTORS CORP.
  11. Remove the spark plug wires (724) from the ignition coils.
    • Twist each plug wire 1/2 turn.
    • Pull only on the boot in order to remove the wire from the ignition coil.
  12. Remove the ignition coil bracket studs (720).
  13. Remove the ignition coil bracket (719).
    14. Fig 7: PCV Hose/Tube
    GM1696757Courtesy of GENERAL MOTORS CORP.
  14. Remove the positive crankcase ventilation (PCV) tube (1) from the valve rocker cover (2).
    15. Fig 8: Valve Rocker Arm Cover (Right)
    GM832211Courtesy of GENERAL MOTORS CORP.
  15. Loosen the valve rocker arm cover bolts.
  16. Remove the valve rocker arm cover.
    17. Fig 9: Rocker Arm Cover Gasket
    GM490696Courtesy of GENERAL MOTORS CORP.
  17. Remove and discard the old gasket (1).
    18. Fig 10: Oil Fill Cap And Oil Fill Tube
    GM1559860Courtesy of GENERAL MOTORS CORP.
  18. Remove the oil fill cap (424) from the oil fill tube (423), if necessary.
  19. Remove and discard the oil fill tube, if necessary.
scientia non olet · About LEMON Manuals