LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 344 (Engine Mechanical - 5.3L, 6.0L & 6.2L - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Engine Front Cover Replacement >> Installation Procedure

Installation Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • Do not reuse the crankshaft oil seal or front cover gasket.
  • Do not apply any type of sealant to the front cover gasket, unless specified.
  • The special tool in this procedure is used to properly center the front crankshaft front oil seal.
    • All gasket surfaces should be free of oil or other foreign material during assembly.
    • The crankshaft front oil seal MUST be centered in relation to the crankshaft.
    • An improperly aligned front cover may cause premature front oil seal wear and/or engine oil leaks.
    Fig 1: CMP Actuator Magnet, Bolts, Gasket And Oil Seal
    GM1658168Courtesy of GENERAL MOTORS CORP.
  1. If replacing the front cover perform the following steps, otherwise proceed to step 10.
  2. Install a NEW CMP actuator magnet gasket (753) onto the magnet.
    3. CAUTION:

    Refer to Fastener Caution .

  3. Install the CMP actuator magnet (752) and bolts (751).

    Tighten 

    Tighten the bolts to 12 N.m (106 lb in).

    4. Fig 2: CMP Sensor And O-Ring
    GM1658166Courtesy of GENERAL MOTORS CORP.
  4. Inspect the CMP sensor O-ring seal for cuts or damage. If the seal is not cut or damaged, it may be reused.
  5. Lubricate the O-ring seal (704) with clean engine oil.
  6. Install the CMP sensor (703).
    7. Fig 3: CMP Sensor Wire Harness And Bolts
    GM1658163Courtesy of GENERAL MOTORS CORP.
  7. Position the CMP sensor wire harness (737) to the front cover
  8. Connect the CMP sensor wire harness to the CMP sensor.
  9. Install the CMP sensor wire harness bolts (738).

    Tighten 

    Tighten the bolts to 12 N.m (106 lb in).

    10. Fig 4: Front Cover, Bolts And Gasket
    GM1658162Courtesy of GENERAL MOTORS CORP.
  10. Apply a 5 mm (0.20 in) bead of sealant, 20 mm (0.80 in) long to the oil pan to engine block junction. Refer to Adhesives, Fluids, Lubricants, and Sealers .
  11. Position the NEW engine front cover gasket (503) and front cover (502) to the engine.
  12. Install the front cover bolts (501) until snug. Do not overtighten.
    13. Fig 5: Oil Pan-To-Front Cover Bolts
    GM832976Courtesy of GENERAL MOTORS CORP.
  13. Install the oil pan-to-front cover bolts (1) until snug. Do not over tighten.
    14. Fig 6: Front And Rear Cover Alignment Tool
    GM451712Courtesy of GENERAL MOTORS CORP.
  14. Install J 41476 to the front cover.
  15. Align the tapered legs of the J 41476 with the machined alignment surfaces on the front cover.
  16. Install the crankshaft balancer bolt until snug. Do not overtighten.

    Tighten 

    1. Tighten the oil pan to front cover bolts to 25 N.m (18 lb ft).
    2. Tighten the engine front cover bolts to 25 N.m (18 lb ft).
  17. Remove the J 41476 .
    18. Fig 7: Electrical Connector, Cable Channel Bolt And Pin
    GM1697734Courtesy of GENERAL MOTORS CORP.
  18. Connect the engine harness electrical connector (1) to the CMP sensor wire harness electrical connector.
  19. Install a NEW crankshaft front oil seal. Refer to Crankshaft Front Oil Seal Replacement (With LY6) .
  20. Install the water pump. Refer to Water Pump Replacement .
scientia non olet · About LEMON Manuals