Liftgate Emblem/Nameplate Replacement (GMC Yukon Hybrid 2 Mode)

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Liftgate Emblem/Nameplate (GMC Yukon Hybrid 2 Mode)

Courtesy of GENERAL MOTORS CORP.

Callout	Component Name
1	Liftgate Emblem/Nameplate Assembly (Yukon) CAUTION: Refer to Exterior Trim Emblem Removal Caution . Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J-25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the liftgate lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the liftgate is made. Special Tools J-25070 Heat Gun

Callout

Component Name

Liftgate Emblem/Nameplate Assembly (Yukon)

CAUTION:

Refer to Exterior Trim Emblem Removal Caution .

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J-25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the liftgate lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the liftgate is made.

Special Tools
J-25070 Heat Gun

Fig 1: Liftgate Emblem/Nameplate (GMC Yukon Hybrid 2 Mode)

Courtesy of GENERAL MOTORS CORP.

Liftgate Emblem/Nameplate Replacement (GMC Yukon Hybrid 2 Mode)

Callout	Component Name
1	Liftgate Emblem/Nameplate Assembly (Hybrid 2 Mode) CAUTION: Refer to Exterior Trim Emblem Removal Caution . Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J-25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the liftgate lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the liftgate is made. Special Tools J-25070 Heat Gun

Callout

Component Name

Liftgate Emblem/Nameplate Assembly (Hybrid 2 Mode)

CAUTION:

Refer to Exterior Trim Emblem Removal Caution .

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J-25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the liftgate lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the liftgate is made.

Special Tools
J-25070 Heat Gun