LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (HVAC - Automatic) >> Diagnostic Information and Procedures >> DTC B0183 or B0188 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Hummer H2. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step verifies that the value displayed is within the specified range.
  2. 3:  This step tests for the proper operation of the circuit in the high voltage range.
  3. 4:  This step tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
DTC B0183 or B0188

Step Action Value(s) Yes No
Schematic Reference: HVAC Schematics 
Connector End View Reference: HVAC Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the appropriate Solar Sensor parameter in the body control module (BCM) data list. Refer to one of the following parameters:
    • Left Solar Sensor
    • Right Solar Sensor
Does the scan tool indicate that the appropriate Solar Sensor parameter is within the specified range?		 5-250 Counts Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the sunload sensor assembly.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the appropriate Solar Sensor data parameter.
Does the scan tool indicate that the appropriate Solar Sensor parameter is greater than the specified value?		 250 Counts Go to Step 4  Go to Step 5 
4 
  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the signal circuit of the sunload sensor assembly and the low reference circuit of the sunload sensor assembly.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the appropriate Solar Sensor parameter.
Does the scan tool indicate that the appropriate Solar Sensor parameter is less than the specified value?		 5 Counts Go to Step 8  Go to Step 6 
5 Test the solar signal circuit of the sunload sensor assembly for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
6 Test the signal circuit of the sunload sensor assembly for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 7 
7 Test the low reference circuit of the sunload sensor assembly for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
8 Inspect for poor connections at the harness connector of the sunload sensor assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 10 
9 Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 11 
10 Replace the sunload sensor assembly. Refer to Sun Load Sensor Replacement .
Did you complete the replacement?		 - Go to Step 12  -
11 Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About LEMON Manuals