LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 161 (Engine Mechanical - 4.8L, 5.3L, 6.0L And 6.2L (4 Of 5)) >> Off-Vehicle Repair Instructions (2 Of 3) >> Cylinder Head Assemble >> Tools Required

Tools Required

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

J 8062  Valve Spring Compressor - Head Off. See Special Tools .

    Fig 1: View Of Valve Components
    GM1559870Courtesy of GENERAL MOTORS CORP.
  1. Clean the cylinder head valve spring shim area.
    2. IMPORTANT: When using the valves and related components again, install the parts to their original location.
  2. Install the valves (228) into the proper port. Refer to Separating Parts .
  3. Install the valve stem oil seal (222).
  4. Install the valve spring (223).
  5. Install the valve spring cap (224).
    6. Fig 2: Compressing Valve Spring Using J 8062
    GM260151Courtesy of GENERAL MOTORS CORP.
  6. Using the J 8062  , compress the valve spring. See Special Tools .
  7. Install the valve stem keys.
    1. Use grease in order to hold the keys in place and remove the J 8062  . See Special Tools .
    2. Ensure the keys seat properly in the groove of the valve stem.
    3. Tap the end of the valve stem with a plastic face hammer to seat the keys, if necessary.
    8. Fig 3: Measuring Valve Spring Installed Height
    GM64315Courtesy of GENERAL MOTORS CORP.
  8. Using a ruler, measure the valve spring installed height.

    Measure from the base of the valve spring to the top of the valve spring.

    Specification: 

    • If the installed height exceeds 46.25 mm (1.82 in), install a valve spring shim of approximately 0.5 mm (0.02 in) thick.
    • Do not shim the valve spring to obtain less than the specified height.

      Do not assemble the components without a spring shim on the cylinder head.

  9. Install the remaining valves, springs, and other components.
    10. Fig 4: Locating Coolant Temperature Sensor
    GM1559875Courtesy of GENERAL MOTORS CORP.
  10. Install sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the coolant temperature sensor (725).
    11. NOTE: Refer to Fastener Notice .
  11. Install the coolant temperature sensor into the left cylinder head.

    Tighten:  Tighten the coolant temperature sensor to 20 N.m (15 lb ft).

    12. Fig 5: Locating Coolant Plug
    GM1559878Courtesy of GENERAL MOTORS CORP.
  12. Install sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the cylinder head plug (229).
  13. Install the cylinder head plug to the right cylinder head.

    Tighten:  Tighten the cylinder head plug to 20 N.m (15 lb ft).

    14. Fig 6: Locating Cylinder Head Core Hole Plug
    GM1559873Courtesy of GENERAL MOTORS CORP.
  14. Apply threadlock GM P/N 12345382 (Canadian P/N 10953489), or equivalent, to the sides of the cylinder head plugs (216).
  15. Install the cylinder head plugs into the cylinder head.

    A properly installed plug should be installed 2.5 mm (0.1 in) below the end face of the head.

scientia non olet · About LEMON Manuals