LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 143 (Automatic Transmission - 4L80-E/4L85-E - DTC P0218 To DTC P0976) >> DTC P0713 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 GMC Yukon XL and 2007 Chevrolet Suburban. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  A value of 4.9-5.0 volts indicates the TCM and engine side of the wiring are good.
  2. 6:  A short to voltage greater than 5 volts would cause the TFT sensor to open.
  3. 9:  A short to the TFT sensor signal circuit and any other circuits in the transmission harness could cause the TFT sensor to open.
DTC P0713

Step Action Value Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.
    3. IMPORTANT: Before clearing the DTCs, use the scan tool in order to record the ECM and TCM Failure Records for reference. Using the Clear Info function will erase the stored Failure Records from the ECM and TCM.
  3. Record the Failure Records.
  4. Clear the DTCs.
  5. With a scan tool, observe the Trans. Fluid Temp. parameter.
Does the scan tool display a TFT greater than the specified value?		 -40°C (-40°F) Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the AT inline 20-way connector.
  3. Connect the J 44152  jumper harness to the engine side of the 20-way connector.
  4. Using the J 35616  GM-approved terminal test kit, connect a DMM to the TFT sensor circuit of the J 44152  jumper harness. Refer to Automatic Transmission Inline 20-Way Connector End View . See Special Tools .
  5. Turn ON the ignition with the engine OFF.
  6. Observe the voltage on the DMM.
Does the voltage measure within the specified range?		 4.9-5.0 V Go to Step 7  Go to Step 4 
4 Does the voltage in Step 3 measure greater than the specified value? 5.0 V Go to Step 6  Go to Step 5 
5
  1. Test the signal circuit of the TFT sensor for an open between the TCM and the AT inline 20-way connector.
  2. Test the low reference circuit of the TFT sensor for an open between the TCM and the AT inline 20-way connector. Refer to Testing for Continuity and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 14  Go to Step 13 
6  Test the signal circuit of the TFT sensor a short to voltage between the TCM and the AT inline 20-way connector. Refer to Testing for a Short to Voltage and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 11  Go to Step 13 
7
  1. Turn OFF the ignition.
  2. Disconnect the AT inline 20-way connector. Additional DTCs may set.
  3. Install the J 44152  on the transmission side of the 20-way connector.
  4. Using the DMM, measure the resistance of the TFT sensor circuit of the J 44152  Refer to Automatic Transmission Inline 20-Way Connector End View .
Is the resistance less than the specified value?		 100 K Ω Go to Step 9  Go to Step 8 
8
  1. Test the signal circuit of the TFT sensor for an open between the AT inline 20-way connector and the TFT sensor.
  2. Test the low reference circuit of the TFT sensor for an open between the AT inline 20-way connector and the TFT sensor. Refer to Testing for Continuity .
Did you find the condition?		 - Go to Step 10  Go to Step 12 
9  Measure the resistance between the TFT sensor signal and all other terminals, except the TFT sensor low reference, of the J 44152  .
Is the resistance greater than the specified value?		 1,000 Ω Go to Testing for Intermittent Conditions and Poor Connections Go to Step 10 
10 Replace the automatic transmission wiring harness assembly. Refer to Valve Body and Pressure Switch Replacement .
Did you complete the replacement?		 - Go to Step 11  -
11 Was the engine harness repaired, or the transmission harness replaced due to a short to power or other circuit? - Go to Step 12  Go to Step 14 
12 Replace the automatic transmission fluid temperature sensor. Refer to Valve Body and Pressure Switch Replacement .
Did you complete the replacement?		 - Go to Step 14  -
13 Replace the TCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 14  -
14 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    • Turn ON the ignition with the engine OFF.
    • Verify that the Trans. Fluid Temp. is greater than -40°C (-40°F) for 2 seconds.
  4. Select Specific DTC.
  5. Enter DTC P0713.

Has the test run and passed?		 - Go to Step 15  Go to Step 2 
15 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals