LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 142 (Automatic Transmission - 4L60-E/4L65-E/4L70-E - DTC P0218 To DTC P0961) >> DTC P0713 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  This step tests the TFT sensor signal circuit for being shorted to another circuit within the transmission. If the TFT sensor signal circuit shorts to another circuit that is greater than 5 volts, the TFT sensor would become open.
  2. 6:  This step tests the TFT sensor signal circuit for being shorted to voltage, which would be the cause for the open in the TFT sensor.
DTC P0713

Step Action Values Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTC, use the scan tool in order to record the DTC Failure Records. Using the Clear Info function erases the Failure Records from the TCM.
  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Select Trans. Fluid Temp. on the scan tool.
Does the scan tool display a Trans. Fluid Temp. less than the specified value?		 -39°C (-38°F) Go to Step 3  Go to Testing for Intermittent Conditions and Poor Connections
3
  1. Turn OFF the ignition.
  2. Disconnect the AT inline 20-way connector. Additional DTCs may set.
  3. Install the J 44152  Jumper Harness (20 pins) on the transmission side of the AT inline 20-way connector. See Special Tools .
  4. Using the DMM and the J 35616  GM Terminal Test Kit, measure the resistance between the TFT sensor signal and low reference circuits of the J 44152  . See Special Tools . Refer to Testing for Continuity .
Refer to Automatic Transmission Inline 20-Way Connector End View .Does the resistance measure less than the specified value?		 100 K Ω Go to Step 7  Go to Step 4 
4
  1. Test the signal circuit of the TFT sensor for an open between the AT inline 20-way connector and the TFT sensor.
  2. Test the low reference circuit of the TFT sensor for an open between the AT inline 20-way connector and the TFT sensor.
Refer to Testing for Continuity .Did you find an open condition?		 - Go to Step 8  Go to Step 5 
5  Measure the resistance between the TFT sensor signal circuit and all other terminals of the J 44152  . See Special Tools .
Refer to Testing for Continuity .
Does the resistance measure less than the specified value?		 1000 Ω Go to Step 10  Go to Step 6 
6  Test the signal circuit of the TFT sensor for a short to voltage between the TCM and the AT inline 20-way connector.
Refer to Testing for a Short to Voltage and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 9  Go to Step 9 
7
  1. Test the signal circuit of the TFT sensor for an open between the TCM and the AT inline 20-way connector.
  2. Test the low reference circuit of the TFT sensor for an open between the TCM and the AT inline 20-way connector.
Refer to Testing for Continuity and Wiring Repairs .Did you find and correct an open condition?		 - Go to Step 12  Go to Step 11 
8 Replace the automatic transmission wiring harness.
Refer to Valve Body and Pressure Switch Replacement .
Did you complete the replacement?		 - Go to Step 12  -
9 Replace the TFT sensor.
Refer to Valve Body and Pressure Switch Replacement .
Did you complete the replacement?		 - Go to Step 12  -
10
  1. Replace the automatic transmission wiring harness.
  2. Replace the TFT sensor.
Refer to Valve Body and Pressure Switch Replacement .Did you complete the replacements?		 - Go to Step 12  -
11 Replace the TCM.
Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 12  -
12 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    • Turn ON the ignition, with the engine OFF.
    • The Trans. Fluid Temp. must be greater than -40°C (-40°F) for 400 seconds.
  4. Select Specific DTC.
  5. Enter DTC P0713.

Has the test run and passed?		 - Go to Step 13  Go to Step 2 
13 With the scan tool, observe the stored information, capture info, and DTC Info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals