LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 138 (Shift Interlock System) >> Diagnostic Information and Procedures >> Shift Lever Can Be Moved without Brake Pedal Depressed

Shift Lever Can Be Moved without Brake Pedal Depressed

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Shift Lever Can Be Moved without Brake Pedal Depressed

Step Action Yes No
Schematic Reference: Shift Lock Control Schematics 
Connector End View Reference: Shift Lock Control Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Shift Lock Solenoid output control ON and OFF.
Does the automatic transmission shift lock control solenoid turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Connect a test lamp between the shift lock control solenoid ground circuit at the connector of the shift lock control solenoid and battery positive voltage.
  4. Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4
  1. Turn OFF the ignition.
  2. Connect a test lamp between the shift lock solenoid control circuit and the shift lock solenoid ground circuit at the connector of the shift lock control solenoid.
  3. With a scan tool, command the Shift Lock Solenoid output control ON and OFF several times.
Does the test lamp turn ON and OFF with each command?		 Go to Step 8  Go to Step 5 
5 Does the test lamp remain illuminated? Go to Step 6  Go to Step 7 
6 Test the control circuit of the automatic transmission shift lock control solenoid for a short to battery voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7 Test the control circuit of the automatic transmission shift lock control solenoid for an open or short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the open in the automatic transmission shift lock control ground circuit. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?		 Go to Step 13  -
11 Replace the automatic transmission shift lock control solenoid. Refer Automatic Transmission Shift Lock Actuator Replacement .
Did you complete the replacement?		 Go to Step 13  -
12 Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals